Bergen 150 Foil/mirror
Assembly Instructions- Please keep for future reference 228/2840
DR8250560
Dimensions
Tip : To prevent damage,
Width - 150cm
Depth - 59.5cm
Height - 199.8cm
we recommend that you
build your unit on the
carton(s) it was packed in.
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928
For any other queries please contact the Customer Helpline on: 0345 640 2020
Issue 3 - 05/11/15
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
•To reduce the
likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Dispose of all packaging
carefully and responsibly.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
Instruction video
• This manual is provided with an additional instruction
video. If the icon on the right is displayed at a particular
step in the manual, Follow the link: http://nlink.nu/vid02
Or scan the QR code on the left with your phone.
• Regularly check and ensure
tightend properly.
See page 2 for link
to instruction video!
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
2
Components - Panels
For damaged or missing parts, please visit:
www.argos-support.co.uk or email: Help@ClickSpares.co.uk
Please check you have all the panels listed below
Left side
1
(199.8 x 52.9cm)
P2883
Top
5
(146.9 x 51cm)
P1889
Plinth x2
7
(146.9 x 6cm)
P7242
Right side
2
(199.8 x 55.8cm)
P2882
Upright
3
(190.3 x 49cm)
P2886
Bottom
6
(146.9 x 51.1cm)
P1891
8
Shelf x2
(72.7 x 48.8cm)
P1893
Foldy back x2
4
(193 x 74cm)
BO3430
Segment x2
9
(76.5 x 65cm)
P3299
Segment middle
13
(76.5 x 65.1cm)
P3268
Mirror door
14
(195.2 x 76.5cm)
PS3333
3
Components - Fittings
For damaged or missing parts, please visit:
www.argos-support.co.uk or email: Help@ClickSpares.co.uk
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
1/2
A
FK1005
Confirmat screw x 4 (5x40mm)
D
FK1309
Screw x 12 (4x12.5mm)
G
FK1052
Double locking screw x 3 (5x66.5mm)
J
FK1248
Corner connector, white x 2
M
FK1235
L-Bracket x 1
P
PM1824
B
Locking screw x 24
(5x24mm)
E
Plug, Nylon x 24 (5x9mm)
H
Wood dowel x 4 (8x30mm)
K
Hanger rail support, gray x 4
N
Nail holder x 1
Q
FK1011
C
Screw x 50 (4x15mm)
FK1082
F
Nail x 60
FK1411
I
Large locking nut x 18 (15x12mm)
FK1217
L
Peg, brown x 1
FK1419
O
Connecting plate x 4
PM1612
R
FK1400
FK1515
FK1012
15mm
FK1234
FK1236
PK1612
Hanger rail x 2
(719mm)
S
Door handle x 3 (1952mm)
V
OR
Allen key x 1 (3mm)
PM1652B
FK1013
Guide rail x 1, metal (1468mm)
T
Brush x 3 (1952mm)
W
PM1652C
ZF99936
Wall plug (6mm) and parkerscrew x 1
Guide rail x 1, plastic(1468mm)
U
Door trim x 1 (1952mm)
PM1652D
4
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
2/2
AA
Screw x 2 (3.5x35mm)
AD
Screw x 2 (4x14mm)
AG
End stop x 2
AJ
Back guide part x 2
ZF9997I
ZF9997J
ZF9997G
ZF9998D
AB
Screw x 7 (3.5x25mm)
AE
Spacer x 1
AH
Stop guide rail x 2
AK
Sliding door connecting plate x 2
ZF9997K
ZF9997F
ZF9997H
ZF9997B
AC
Screw x 33
AF
(4x15mm)
ZF9997L
ZF9997E
Tapping block for guide rail x 2
AI
ZF9997C
Front guide part x 2
AL
ZF9997A
Sliding door connecting bracket x 2
Tools required
Phillips screwdriver
(medium & large)
Stairs
Drill
Flatblade screwdriver
(medium)
Piercer
(small)
Spirit level
5mm Suitable drill bit
5mm Suitable drill bit
Setsquare
Ruler - Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Eye protection
(when using a
hammer or drill)
Small
hammer
Ruler/tape
measure
Scissors
5
Assembly Instructions
Step 1
a:
Cabinet assembly
a: Screw 9 locking screws
B
into the holes on back
of the left side 1.
AB
D
D
Mount hanger rail support
K, fasten with 1 screw D.
Screw D into the board
between two predrilled
holes.
Mount tapping block for
guide rail f with two
screws b.
b: Screw 9 locking screws
B into the holes on back
of the right side 2 .
Mount hanger rail
support K, fasten with 1
screw D. Screw D into
the board between two
predrilled holes.
Mount tapping block for
guide rail f with two
screws b.
AF
b:
AB
AB
AF
AF
AB
K
Finished
front edge
D
K
AF
AB
1
AB
Finished
front edge
2
C: Mount hanger rail
support K on the
upright 3, fasten with
screw D 1x. Screw D
into the board between two
predrilled holes
Turn over.
Mount hanger rail
support K on the
upright 3, fasten with
screw D 1x. Screw D into
the board between two
predrilled holes.
6
c:
D
K
3
Finished
front edge