Hygena 305-0693, 305-0686, 181-8985 Instruction manual

MADE IN

BRITAIN

Dimensions

Width - 80cm

Depth - 39cm

Height - 101.5cm

Camden - 5 Drawer Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 3 - 12/12/13

Important - Please read these instructions fully before starting assembly

305/0686

305/0693

181/8985

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 34kgs. Please lift with care.

• Check you have all the components and tools listed on pages 1, 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Tools required

Rule Scissors Hammer Eye protection

(when using a hammer or drill)

Cross-head screwdriver

Electric drill (only use when drilling into walls)

Components - Panels

Please check you have all the panels listed below

1 2

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

7 8

Drawer Base (T546)

(683 x 317mm) x 5

Drawer Back (W546)

(672 x 105mm) x 5

Back (X943)

(932 x 740mm)

Left Drawer Side (W418LH)

(320 x 105mm) x 5

Right Drawer Side (W418RH)

(320 x 105mm) x 5

Plinth (D1994A)

(722 x 96mm) x 2

Left Side (D1992A)

(979 x 389mm)

Top (D1991A)

(796 x 391mm)

Drawer Front (D1995A)

(716 x 173mm) x 5

Right Side (D1993A)

(979 x 389mm)

Please check you have all the fittings listed below

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Wooden dowel (F22) x 4

Metal dowel (F901) x 14

Large locking nut (F900) x 4

Small locking nut (F3) x 10

Small metal dowel (F893) x 4

19mm Screw (F461) x 10

Nail (F51) x 23

J K

Hollow core locking nut (F892) x 4

Bracket (F327) x 1

Wedgefix (F639) x 20

Knock-in Peg (F171) x 20

13mm Screw (F63) x 30

13mm Screw (F52) x 30

13mm Screw (F79) x 1

R Runner (F160) x 5

L Runner (F161) x 5

L Runner (F159) x 5

R Runner (F162) x 5

Handle (F227) x 5

624mm

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Prepare the 5 drawer fronts

Screw 2 metal dowels into the holes shown on the back of each drawer front .

Note: Tighten metal dowels up fully against the panels.

Prepare drawer sides and drawer backs

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 2

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

x 5

x 5 x 5

x 5

Step 3

Attach the drawer sides to the drawer front

Push the left drawer side . and right drawer side . onto the back of the drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

7 8

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

Groove

+ 11 hidden pages