Page 1
MADE IN
BRITAIN
Dimensions
Width - 100cm
Depth - 49.5cm
Height - 43.5cm
Aurora - Coffee Table
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 4 - 26/05/15
Important - Please read these instructions fully before starting assembly
147/1360
166/6553
417/9009
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 26kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Page 3
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Left Side (D2638A)
(420 x 459mm)
Back (D2641A)
(985 x 192mm)
Rail (D2643A)
(959 x 95mm) x 3
32
Right Side (D2639A)
(420 x 459mm)
Horizontal (D2640A)
(959 x 456mm)
Drawer Front (D2642A)
(985 x 192mm)
Top (D2644A)
(999 x 495mm)
Drawer Back (W908-115)
(908 x 115mm)
54
6
8
7
9 10 11
Drawer Base (T919-347)
(919 x 347mm)
Left Drawer Side
(W350-115LLH)
(350 x 115mm)
Right Drawer Side
(W350-115LRH)
(350 x 115mm)
Page 4
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 16
C
D
Large locking
nut (F900) x 14
E F
G H I
Small locking
nut (F3) x 2
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K
Door Plate (F259) x 1
25mm Screw (F50) x 2 13mm Screw (F52) x 8
13mm Screw (F63) x 6
L
N
Door Push (F258) x 1
Feet (F854) x 2
Knock-in Peg (F171) x 4
M
R Runner (F160) x 1
b
L Runner (F161) x 1
M
c
L Runner (F159) x 1
M
a
R Runner (F162) x 1
M
d
350mm long
Wedgefix (F639) x 6
Mini block (F25) x 4
Page 5
5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
B
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the holes shown on
the back of the drawer
front .
Note: Tighten the metal
dowels up fully against
the panels.
B
5
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Step 3
D
9
10
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
10
9
10
5
D
9
10
Groove
D
D
B
5
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the groove is on the inside, as shown.
D
10
9
B
B
B
D
9
Page 6
C
C
5
5
Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
8
9 10
5
11
9 10
8
11
11
C
9 10
8
8
9
10
11
9
10
8
C
C
N
N
N
N
N
N
N
Step 6
Fit the 6 wedgefixes
Turn the drawer
assembly over.
Slide the wedgefixes
into the small grooves on
the drawer assembly, as
shown.
Once in place, tighten up
the screws.
N
Page 7
A
M d
R
R
Assembly Instructions
6
Step 7
Fit the runners to the
drawer
Turn the drawer
assembly over.
Fit runner , marked
with ‘R’, to the bottom
edge of the right drawer
side , as shown,
making sure that it is
pushed up against the
back of the drawer front
. . Use a bradawl to
mark the fixing positions,
then secure with 2
screws .
Fit runner , marked
‘L’, to the bottom edge
of the left drawer side
using the same method.
9
M d
10
5
J
M c
Runners must be
pushed up against
the drawer front
J
J
L
M c
L
J
J
9
10
5
Prepare the horizontal
Tap 2 wooden dowels
into the horizontal .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 4 large locking
nuts into the
horizontal .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
A
3
3
E
Step 8
E
E
E
E
A
Finished
front edge
plain chipboard surface
3
E
10mm
A
Page 8
Finished
front edge
Finished
front edge
A
Assembly Instructions
7
Step 9
a:
b:
c:
B
B
B
H
M a
H
H
M a
Finished front edge
J
J
M a
H
Finished front edge
H
1st
screw
2nd
screw
H
3rd
screw
Prepare the left side
a: Tap a wooden dowel
. into the left side .
Screw 5 metal dowels
into the left side .
b: Insert 2 large locking
nuts into the left side
. .
Fit the runner to the
left side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
c: Fit a screw into
the 2nd hole in at the top
of the runner .
Gently tap 2 mini blocks
. into the left side ,
orientated as shown.
H
H
A
1
B
1
J
M a
1
Finished
front edge
1
1
1
M a
E
E
B
E
1
B
I
I
I
I
1
Page 9
Assembly Instructions
8
Step 10
a:
b:
c:
Prepare the right side
a: Tap a wooden dowel
. into the right side .
Screw 5 metal dowels
into the right side .
b: Insert 2 large locking
nuts into the right
side .
Fit the runner to the
right side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
c: Fit a screw into
the 2nd hole in at the top
of the runner .
Gently tap 2 mini blocks
. into the right side ,
orientated as shown.
H
H
A
2
2
E
2
J
M b
2
A
B
B
B
M b
H
Finished front edge
H
1st
screw
2nd
screw
H
3rd
screw
H
H
M b
H
Finished
front edge
Finished
front edge
M b
Finished front edge
J
J
Finished
front edge
2
2
2
M b
E
E
B
B
B
I
I
I
I
2
Page 10
A
Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 11
Join the right side and
horizontal
Push the horizontal
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
B
E
3
2
E
E
3
3
2
plain chipboard surface
Step 12
E
E
A
Prepare 1 of the rails
Tap 2 wooden dowels
into a rail .
Insert 2 large locking
nuts into a rail .
A
6
E
6
6
x 1
x 2
Step 13
A
E
E
A
6
G
F
Prepare the other 2
rails
Tap 2 wooden dowels
into each rail .
Insert 2 large locking
nuts into each rail .
Screw a foot onto
each rail between the
2 pre-drilled holes using
screws .
A
6
6
E
6
G
F
G
F
Page 11
Assembly Instructions
10
Step 14
Step 15
6
Turn over 1 of the
rails with a foot and
fit the door push
Fit a door plate to one
of the rails using
screws .
Press the door push
into the door plate .
Press down the back of
the door push to click
into place.
L
K
L
K
6
H
2
Fit the 3 rails
Push the rails onto
the right side .
Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the rails .
6
2
E
6
6
6
6
Note: Support these
2 rails until the left
side has been fitted.
Door push
Foot
Foot
This rail
does not
have a foot
x 1
Foot
underneath
L
K
K
H
L
H
K L
+
Finished
front edge
Page 12
Assembly Instructions
Step 16
11
Step 17
Fit the back
Push the holes in the
back down onto the
4 mini blocks fitted to
the sides.
Tighten up the screws in
the 4 mini blocks into
the holes in the back .
Carefully stand the
unit up for the next
step.
4
Finished
top edge
4
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the horizontal and
the rails .
6
6
1
3
1
E
3
6
6
I
I
I
4
Page 13
Assembly Instructions
12
Step 18
Step 19
B
B
B
B
Prepare the top
Screw 4 metal dowels
into the top .
Use the measurements
of the holes to determine
which is the front edge.
B
7
7
95mm
80mm
Front
edge
Front
edge
Fit the top
Push the top down
onto the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left side and right
side .
E
1
2
7
1
2
7
Page 14
Assembly Instructions
13
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 20
Fit the drawer
Slide the wheels of the
runners fitted to the
drawer, over the wheels
of the runners fitted to
the side panels and push
the drawer into position.
Assembly is complete
Side
panel
Drawer
Adjust the drawer if
required
You can adjust the door
push for the drawer in or
out, by turning it
clockwise or anticlockwise to suit your
requirements.
Adjustment
L
Step 21
Note: Now the assembly has finished you can
remove any protective film from the panels.
Page 15
Page 16
ALR2939
Loading...