Hygena 1707034, 151-4203, 152-9614 ASSEMBLY INSTRUCTIONS
Hamlin- 3 Doors Robe
Assembly Instructions - Please keep for future reference
h y g e n a
152/4877
151/4203
152/9614
Dimensions
Width - 120cm
Depth - 55,8cm
Height - 192cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Issue 1 - 28/10/13
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not
recommend the
use of power
drill/driversfor
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
Care and maintenance
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
Use a dry cloth to clean the
product, furniture polish is
not recommended.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
Note:If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Components - Panels
Please check you have all the panels listed below
Right side panel
1
top
Left side panel
2
Middle wall panel
3
(190 x 54cm)
(190 x 54cm)
(178.8 x 54cm)
top
top
Top panel
9
Base panel (117 x 54cm)
10
underside
(120 x 55.8cm)
underside
Door x 3
4
Door knocker x 3
5
Left back panel x 2 (180.8 x 39.1cm)
6
Right back panel (180.8 x 40cm)
7
(179 x 35cm)
(178 x 8cm)
Left shelf
11
underside
Right shelf
12
Bottom frame
13
Unfinished bottom frame(117 x 9.6cm)
14
Left hanging rail
15
(77 x 52.7cm)
(38.5 x 52.7cm)
(117 x 9.6cm)
(76.2 x 3cm)
8
H profile
(179 x 1.8cm)
Right hanging rail
16
(37.7 x 3cm)
2
If you have damaged or missing components,
Components - Fittings
call the Customer Helpline: 08456 400 800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A B
Ø 6X30 Wooden dowel x 24
Ø 6X50 Wooden dowel x 2
D E F
16mm Screw x 114mm Screw x 36
Locking
Metal dowel x 20
J
nut x 20
K
Plastic
Nail x 6
feet x 6
M
Hanging rail
support x 4
P
Bracket x 18
Washer x 2
Q
Wall strap x 1
C
14mm Screw x 32
25mm Screw x 21
IG H
Nail x 94
L
L shaped
bracket x 6
ON
Plastic
x 20
cap
R
Door
hinge x 9
Tools required
Phillips screwdriver
(small & medium)
Small
hammer
Ruler - Use this ruler to help correctly identify the screws
5
0
10 15 20 25 30 35 40
3
55
45
50
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
m
2
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
Assembly Instructions
Step1
Insert dowels into the
A
indicated parts.
Fix hanging rail support
M
in the pre marked
holes on right side panel
1
and left side panel
2
using screws , as
C
shown.
C
M
1
and
A
2
3
10
A
A
A
Step2
Insert dowels and
into right shelf as
shown.
A
12
A
A
Finished edge.
A
B
11
13
14
A
A
A
Finished edge.
12
B
A
B
4
Assembly Instructions
Step3
a:
Fitting hinges.
Loosen screw in door
a:
hinge and separate
the ‘back plate’.
R
R
R
R
b:
2
D
R
b:Attach ‘back plates’
in the pre marked holes
on right and left side
panels and using
screws .
1
D
Attach ‘back plates’ in
the pre marked holes on
middle wall panel
using screws .
2
R
3
D
R
R
R
1
R
R
R
3
R
R
5
Loading...