Emmett - Pair of Upholstered Chairs
Assembly Instructions - Please keep for future reference
149/2772
149/2789
Dimensions
Width - 48cm
Depth - 62cm
Height - 87.3cm
Important - Please read these instructions fully before starting assembly.
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 29/06/12IW-17-7521-112/ 132-0
Safety and Care Advice
Important - Please read these instructions fully before starting assembly.
• Check you have all the
components and tools listed on
page 2.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft flat / firm
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• We do not
recommend the
use of power
drill/ drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly .
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Seat pad x 2
2
(46 x 48cm)
2
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A B C
30mm Round head screw x 4 60mm Hex head bolt x 8 50mm Hex head bolt x 4
D E F
50mm Threaded bolt x 4 Flat washer x 4 Lock washer x 4
G H J
Hex nut x 4
Tool required
Spanner x 1 Allen key x 1
Phillips screwdriver
(medium & large)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150105 155 160 165 170
3
Assembly Instructions
Step 1
Attaching back legs
and back rest
Fix back legs and
to back rest using 2
screws as shown.
A
3
1
4
Use a screwdriver to turn
fitting clockwise to fix.
A
L
3
A
A
3
A
4
R
4
1
Step 2
Attaching seat pad
a: Lift under cloth up and
lay back as shown.
b: Insert lock washer
and flat washer onto
each bolt as shown.
Insert bolts with lock
washers and flat
washers through the
pre-drilled holes of seat
pad and back rest
into back legs and .
Tighten bolts into the
fittings inside back legs
and .
3 4
Use allen key to turn
fitting clockwise to fix.
B
B
F
E
3 4
B
J
B
F
E
12
b:
B
F
E
B
F
E
J
2
1
a:
3
Continued on next page.
4
4