Hygena 147-1360, 166-6553, 417-9009 Instruction manual

MADE IN
BRITAIN
Dimensions
Width - 100cm
Depth - 49.5cm
Height - 43.5cm
Aurora - Coffee Table
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 4 - 26/05/15
Important - Please read these instructions fully before starting assembly
147/1360
166/6553
417/9009
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 26kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Left Side (D2638A)
(420 x 459mm)
Back (D2641A)
(985 x 192mm)
Rail (D2643A)
(959 x 95mm) x 3
32
Right Side (D2639A)
(420 x 459mm)
Horizontal (D2640A)
(959 x 456mm)
Drawer Front (D2642A)
(985 x 192mm)
Top (D2644A)
(999 x 495mm)
Drawer Back (W908-115)
(908 x 115mm)
54
6
8
7
9 10 11
Drawer Base (T919-347)
(919 x 347mm)
Left Drawer Side
(W350-115LLH)
(350 x 115mm)
Right Drawer Side
(W350-115LRH)
(350 x 115mm)
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 16
C
D
Large locking nut (F900) x 14
E F
G H I
Small locking nut (F3) x 2
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K
Door Plate (F259) x 1
25mm Screw (F50) x 2 13mm Screw (F52) x 8
13mm Screw (F63) x 6
L
N
Door Push (F258) x 1
Feet (F854) x 2
Knock-in Peg (F171) x 4
M
R Runner (F160) x 1
b
L Runner (F161) x 1
M
c
L Runner (F159) x 1
M
a
R Runner (F162) x 1
M
d
350mm long
Wedgefix (F639) x 6
Mini block (F25) x 4
5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
B
Step 2
Prepare the drawer front
Screw 2 metal dowels into the holes shown on the back of the drawer front .
Note: Tighten the metal dowels up fully against the panels.
B
5
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and right drawer side .
Note: Arrow on locking nut must point towards hole in edge of panel.
Step 3
D
9
10
Attach the drawer sides to the drawer front
Push the left drawer side . and right drawer side . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
10
9
10
5
D
9
10
Groove
D
D
B
5
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the groove is on the inside, as shown.
D
10
9
B
B
B
D
9
Loading...
+ 11 hidden pages