Hygena 1949768, 145-8390, 145-5726 ASSEMBLY INSTRUCTIONS

Hamlin - 2 Drawers Dresser

Assembly Instructions - Please keep for future reference

h y g e n a

145/8390

152/5340

145/5726

Dimensions

Width - 90cm

Depth - 44,8cm

Height - 74cm

Important – Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800

Issue 1 - 28/10/13

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

Check you have all the
components and tools listed on
pages 2 and 3.

Remove all fittings from the
plastic bags and separate them
into their groups.

Keep children and animals
away from the work area, small
parts could choke if swallowed.

Make sure you have enough
space to layout the parts before
starting.

Do not stand or put weight on
the product, this could cause
damage.

Assemble the item as close
to its final position (in the same
room) as possible.

Assemble on a soft level
surface to avoid damaging the
unit or your floor.

We do not
recommend the
use of power
drill/drivers for

inserting screws,

as this could damage the unit.
Only use hand screwdrivers.

Parts of the assembly will be

easier with 2 people.

Dispose of all packaging

carefully and responsibly.

Care and maintenance

Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.

Use a dry cloth to clean the
product, furniture polish is
not recommended.

From time to time check
that there are no loose
screws on this unit.

This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

1

Components - Panels

Please check you have all the panels listed below

Top panel (90 x 44.8cm)

1

Middle wall panel

6

(17.5 x 43cm)

Drawer front x 2

7

(43.6 x 15cm)

Right side panel (72 x 43cm)

2

Top

Left side panel (72 x 43cm)

3

Top

Drawer back x 2

8

(37.2 x 8cm)

Drawer right side x 2

9

(40 x 8cm)

Drawer left side x 2

10

(40 x 8cm)

Top front frame x 2

11

(42.6 x 6cm)

Base panel (86.8 x 43cm)

4

Back panel (88.8 x 19.5cm)

5

Drawer bottom x 2

12

(39.8 x 38.5cm)

2

If you have damaged or missing components,

Components - Fittings

call the

Customer Helpline: 08456 400 800

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.

A B

Ø 6X30 Wooden dowel x 24

Ø 6X50 Wooden dowel x 2

D E F

20mm Screw x 4

40mm Screw x 4

Locking
nut x 16

J

Plastic

feet x 4

M

Right runner
x 2 pair

K

Plastic

bracket x 4

N

Left runner
x 2 pair

C

14mm Screw x 16

Metal dowel x 16

IG H

Nail x 4Nail x 30

L

Plastic

x 14

cap

Tools required

Phillips screwdriver
(small & medium)

Small
hammer

Ruler - Use this ruler to help correctly identify the screws

5

0

10 15 20 25 30 35 40

3

55

45

50

60 65 70

75

80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170

m

2

Ruler/tape
measure

Eye protection
(when using a
hammer or glue)

Assembly Instructions

Step 1

Insert dowels into the

A

indicated parts.

2

A

3

A

4

A

Step 2

A

6

A

11

1x

8

2x

A

A

A

9

2x

A

10

2x

A

Insert dowels and

A

into the top front frame

11

, as shown.

B

11

1x

B

A

4

Assembly Instructions

Step 3

Fitting Metal dowels.

Screw metal dowels
into top panel , base
panel , right side panel

4

2

, left side panel

and drawer fronts .

F

1

3

7

Insert metalNote:
dowels as far as
shown.

Do not over tighten.

F

F

F

F

F

4

1

F

7

2x

F

2x

2 3

Step 4

Fixing middle wall panel.

With help, fit middle wall
panel to base panel

Insert 2 locking nuts
into middle wall panel
where shown.

Use a screwdriver to turn
locking nuts clockwise
to lock.

Do not over tighten.

wall painel and base
panel are facing down.

6

4

.

G

Make sure finished
edges of middle

G

4

Painted edge to
face down.

G

G

G

6

G

5

Assembly Instructions

Step 5

Fixing runners.

a: Attach right runner

to the pre drilled holes
on the right side panel

using screws .

b: Attach left runner

to the pre drilled holes on
the left side panel
using screws .

B

M

B2

N

3

a:

M

b:

B

2

M

B

3

N

c: Attach right runner

to the pre drilled holes
on the left side of middle
wall panel using
screws .

Attach left runner to
the pre drilled holes on
the right side of middle
wall panel using
screws .

6

B

6

B

M

N

c:

M

N

N

6

N

B

M

B

6

Assembly Instructions

Step 6

Fitting top front frames.

Fit top front frames to

11

middle wall.

Attention!

Top front frame

with longer wooden

dowel

should be fitted first.

Step 7

Fixing side panels.

Painted side to
face down.

11

Attention!

11

B

With help, fit right side
panel and left side
panel to base panel

3

2

and top front frames.

Insert 4 locking nuts

G

into base panel where
shown.

Use a screwdriver to turn
locking nuts clockwise

G

to lock.

Do not over tighten.

After screwing locking
nuts, insert plastic caps

L

.

Important:

After inserting
plastic caps, with help,
carefully stand the
product upright.

2

G

3

G

G

G

L

7

Assembly Instructions

Step 8

Fixing top panel.

With help, fit top panel

1

to the cabinet.

Insert 4 locking nuts

G

into side panels and 2
locking nuts into middle

G

wall panel where shown.

Use a screwdriver to turn
locking nuts clockwise

G

to lock.

Do not over tighten.

After screwing locking
nuts, insert plastic caps

L

.

Finished edge

1

G

G

G

G

G

L

8

Assembly Instructions

Step 9

Fixing back panels.

Important:

Cabinet beMUST
‘square’ when back panel
is attached.

Attach back panel
using nails .

H

5

After attach back panel,
with help, carefully lay
down the product.

H

H

H

Step 10

Attach plastic feet.

Attach p in

lastic feet

the bottom edge of the
right and left side panels
using nails .

I

Make sure nails

are fully nailed.

After attach plastic feet,
with help, carefully stand
the product upright.

J

J

I

J

J

J

9

Assembly Instructions

Step 11

Drawer assembly.

a: Fix drawer sides

10

and to the drawer
back using screws .

8

9

E

b: Slide drawer bottom

12

into slots on drawer

sides.

c: With help, fit drawer

front to the drawer
sides.

Insert 2 locking nuts
into drawer sides where
shown.

Use a screwdriver to turn
locking nuts clockwise
to lock.

7

G

G

a:

E

8

E

10

9

b:

12

c:

7

G

Do not over tighten.

After screwing locking
nuts, insert plastic caps

L

.

Repeat step 11 for the
other drawer.

Step 12

Attach plastic bracket.

Attach p

drawers using screws .

lastic bracket

of thein the bottom

K

D

G

K

K

G

K

L

D

10

Assembly Instructions

Step 13

Fixing runners.

Attach right runners
and left runners in the
bottom edge of the
drawers using screws ,
as shown.

Make sure

runners are
correctly positioned
according to the diagram
prior to fixing.

M

N

C

Correct position of the screws.

C

C

BB

C

C

M

IN FLUSH

N

IN FLUSH

Step 14

Hook the wheels of the
runner on the back of the
drawers over the wheels
of the runners on the left
and right sides, then hold
the drawers level and
slide backwards into
position.

Assembly is complete.

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800

11