Page 1
Hamlin - Bedside
Assembly Instructions - Please keep for future reference
h y g e n a
143/4235
152/5230
145/6103
Dimensions
Width - 45,2cm
Depth - 44,8cm
Height - 50,5cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Issue 1 - 28/10/13
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
Care and maintenance
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
Use a dry cloth to clean the
product, furniture polish is
not recommended.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Page 3
Components - Panels
Please check you have all the panels listed below
Large drawer front
5
(43 x 19cm)
Top panel
1
(45.2 x 44.8cm)
Large drawer back
7
(36.6 x 12cm)
Top
Large drawer right
9
side (40 x 12cm)
Small drawer front
6
(43 x 15cm)
Small drawer back
8
(36.6 x 8cm)
Large drawer left
10
(40 x 12cm)
side
Right side panel
2
(48.5 x 43cm)
Top
Left side panel
3
(48.5 x 43cm)
Small drawer right
11
(40 x 8cm)
side
Bottom frame
13
(42 x 7cm)
Top front frame x 2
15
(42 x 6cm)
Small drawer left
12
(40 x 8cm)
side
Unfinished bottom
14
frame (42 x 7cm)
Back panel
4
(44 x 44cm)
Drawer bottom x 2
16
(39.8 x 37.9cm)
2
Page 4
If you have damaged or missing components,
Components - Fittings
call the
Customer Helpline: 08456 400 800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A B
Wooden dowel x 32
D
40mm Screw x 4
Nail x 23
J
Plastic
bracket x 4
Right runner
x 4 pair
14mm Screw x 32
E F
Metal dowel x 8
Nail x 4
K
L shaped
bracket x 4
NM
Left runner
x 4 pair
C
20mm Screw x 4
Locking
nut x 8
IG H
Plastic
feet x 4
L
Plastic
x 8
cap
Tools required
Phillips screwdriver
(small & medium)
Small
hammer
Ruler - Use this ruler to help correctly identify the screws
5
0
10 15 20 25 30 35 40
3
55
45
50
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
m
2
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
Page 5
Assembly Instructions
Step 1
Insert dowels into the
A
indicated parts.
2
A
3
A
A
7
A
8
A
A
11
A
12
A
A
15
2x
13
A
A
10
A
14
9
A
A
A
A
4
Page 6
Assembly Instructions
Step 2
Fixing runners.
Attach right runners
M
to the pre drilled holes
on the right side panel
using screws .
Attach left runners
B2
N
to the pre drilled holes on
the left side panel
using screws .
3
B
M
B
N
M
2
B
N
Step 3
Fitting Metal dowels.
Screw metal dowels
into top panel , large
drawer front and small
drawer front .
5
6
Insert metalNote:
dowels as far as
shown.
Do not over tighten.
E
1
3
E
E
E
6
E
E
5
E
E
1
5
Page 7
Assembly Instructions
Step 4
Fixing L shaped brackets.
Unfinished side
B
Fix L shaped brackets
in the bottom frame
K
13
and unfinished bottom
B
, a
14
s shown.
Attention:
space from the1mm
13
Leave
frame using screws
edge of the bars as shown.
L shaped brackets must be
fixed to the unfinished side
in bottom frame .
Step 5
Assembling frames.
Fit bottom frame and
14
and top front frames
15
into holes on right
side panel , as shown.
Then, fix bottom frames
13 14
and in the right
side panel through L
shaped brackets using
screws .
B
13
2
K
K
K
Finished sides to face
outside and finished
edges to face up.
15
15
13
13
K
14
14
K
K
Attention:
K
13 14
1mm
B
K
Finished sides to
face outside and
finished edges to face up.
Step 6
Fixing left side panel.
Place left side panel
properly ensuring dowels
and front frames are all
fitted into their holes at
the same time.
Fix bottom frames and
14
in the left side panel
3
brackets using screws
B
, as shown.
L shapedthrough
K
3
13
2
3
K
K
13
14
B
6
Page 8
Assembly Instructions
Step 7
Fixing top panel.
With help, carefully
stand the product upright.
With help, fit top panel
1
to the cabinet.
Insert 4 locking nuts
F
into side panels where
shown.
Use a screwdriver to turn
locking nuts clockwise
F
to lock.
Do not over tighten.
After screwing locking
nuts, insert plastic caps
L
.
Finished edge
F
F
1
F
F
L
Step 8
Fixing back panel.
Important:
Cabinet beMUST
‘square’ when back panel
is attached.
Attach back panel
using nails .
G
4
G
4
G
G
7
Page 9
Assembly Instructions
Step 9
Attach plastic feets.
With help, carefully lay
down the product.
Attach p inlastic feets
the bottom edge of the
right and left side panels
using nails .
H
I
I
H
Make sure nails
are fully nailed.
After attach plastic feets,
with help, carefully stand
the product upright.
Step 10
Large drawer
assembly.
a: Fix large drawer
sides and to the
large drawer back
using screws .
9
b: Slide drawer bottom
16
into slots on drawer
sides.
10
7
D
I
I
I
D
a:
7
D
10
9
b:
c: With help, fit large
drawer front to the
drawer sides.
Insert 2 locking nuts
into drawer sides where
shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
Do not over tighten.
After screwing locking
nuts, insert plastic caps
L
.
5
F
F
c:
16
5
F
F
F
L
8
Page 10
Assembly Instructions
Step 11
Small drawer
assembly.
a: Fix small drawer
sides and to the
small drawer back
using screws .
11 12
8
D
b: Slide drawer bottom
16
into slots on drawer
sides.
a:
D
12
D
8
11
b:
c: With help, fit small
drawer front to the
drawer sides.
Insert 2 locking nuts
into drawer sides where
shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
Do not over tighten.
After screwing locking
nuts, insert plastic caps
L
.
6
F
F
Step 12
Attach plastic bracket.
Attach plastic bracket
in the bottom of the large
and small drawers using
screws .
C
J
c:
15
16
6
F
F
F
C
J
L
J
9
Page 11
Assembly Instructions
Step 13
Fixing runners.
Attach right runners
and left runners in the
bottom edge of the large
and small drawers using
screws , as shown.
B
Make sure
runners are
correctly positioned
according to the diagram
prior to fixing.
M
N
Correct position of the screws.
B
B
BB
B
B
M
IN FLUSH
N
IN FLUSH
Step 14
Hook the wheels of the
runner on the back of the
drawers over the wheels
of the runners on the left
and right sides, then hold
the drawers level and
slide backwards into
position.
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
10
Loading...