HydroTherm HV, HW User's Information Manual
UMHV3-1
INSTALLER, THIS MANUAL TO BE AFFIXED ADJACENT TO THE BOILER.
CONSUMER, RETAIN THIS MANUAL FOR FUTURE REFERENCE PURPOSES.
HV & HW GAS BOILERS
USER’S INFORMATION MANUAL
DESIGNED AND TESTED ACCORDING TO A.S.M.E. BOILER AND PRESSURE
VESSEL CODE, SECTION IV FOR A MAXIMUM ALLOWABLE WORKING
PRESSURE OF 50 PSI, 345 kPa WATER.
WARNING: If the information in this manual is not followed exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch. Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or the
gas supplier.
WARNING: Never store combustible materials, gasoline or any product containing
flammable vapors or liquids in the vicinity of the boiler/water heater. Failure to comply
with this warning can result in an explosion or fire causing extensive property
damage, severe personal injury or death!
WARNING: Failure to properly vent this unit can cause excessive amounts of carbon
monoxide resulting in severe personal injury or death!
HV & HW USER’S INFORMATION MANUAL
Page 2
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause
property damage, personal injury (exposure to
hazardous materials)* or loss of life. Installation
and service must be performed by a qualified
installer, service agency or the gas supplier (who
must read and follow the supplied instructions
before installing, servicing or removing this boiler.
This boiler contains crystalline silica materials that
have been identified as carcinogenic or possibly
carcinogenic to humans when inhaled)*.
AVERTISSEMENT: Une installation, un réglage, une
modi-fication, une réparation ou un entretien non
comforme aux normes peut entraîner des
dommages matériels, des blessures (exposition à
des matières dangereuses) ou la mort. L’installation
et l’entretien doivent être effectués par un
installateur ou un service d’entretien qualifié ou le
fournisseur de gaz (qui doivent avoir lu les
instructions fournies avant de faire l’installation,
l’entretien ou l’enlèvement de la chaudière et les
respecter, Cette chaudière contient des matériaux
qui ont été identifiés comme étant cancérogènes
ou pouvant l’ être).
All aspects of the boiler installation must conform to the
requirements of the authority having jurisdiction, or, in
the absence of such requirements, to the latest edition
of the National Fuel Gas Code, ANSI Z223.1/NFPA 54.
Where required by the authority having jurisdiction, the
installation must conform to the Standard for Controls
and Safety Devices for Automatically Fired Boilers,
ANSI/ASME CSD-1.
In Canada, the installation must be in accordance with
the requirements of CSA B149.1 or .2, Installation Code
for Gas Burning Appliances and Equipment.
AVERTISSMENT. Assurez-vous de bien suivre les instructions données dans cette
notice pour réduire au minimum le risque d’incendie ou d’explosion ou pour éviter
tout dommoge matériel, toute blessure ou la mort
Ne pas entreposer ni utiliser d’essence ou ni d’autres vapeurs ou liquides
inflammables à proximité de cet appareil ou de tout autre appareil.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
• Ne pas tenter d’allumer d’appareil.
• Ne touchez à aucun interrupteur; ne pas vous servir des téléphones se trouvant
dans le bâtiment.
• Appelez immédiatement votre fournisseur de gas depuis un voisin. Suivez les
intructions du fournisseur.
• Si vous ne purvez rejoindre le fournisseur, appelez le service des incendies.r
L’installation et l’entretien doivent être assurés par un installateur ou un service
d’entretien qualifié ou par le fournisseur de gaz.
The owner should maintain a record of all service work
performed with the date and a description of the work
done. Include the name of the service organization for
future reference.
Direct all questions to your HydroTherm distributor or
contact the HydroTherm Customer Service Department
at: 260 North Elm Street, Westfield, MA 01085. Always
include the model and serial numbers from the rating
plate of the boiler/water heater in question.
CAUTION: Servicing, inspection and adjustment must
be done by a trained technician in accordance with all
applicable local and national codes. Improper servicing
or adjustment can damage the boiler!
The boiler should be cleaned and inspected once a year,
before each heating season. Make sure that the burner,
ignition components and vent system are free from dust,
soot, dirt, corrosion or other deposits that would impair
the boiler performance and safe operation.
Should overheating occur or the gas supply fail to shut
off, do not turn off or disconnect the electrical supply to
the pump. Instead, shut off the gas supply at a location
external to the appliance.
En cas de surchauffe ou si l’alimentation de gaz ne peut
être coupée, ne pas couper ni débrancher l’alimentation
électrique de la ponpe. Fermer plutôt le robinet d’admission de gaz à l’extérieur de l’appareil.
Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system and any gas control that has been
under water.
N’utilisez pas cet appareil s’il a été plongé dans l’eau,
même partiellement. Faites inspecter l’appareil par un
tecnicien qualifié et remplacez toute partie du système
de contrôle et toute commande qui ont été plongés dans
l’eau.
1. STOP! Read the safety information above.
2. Set the thermostat to lowest setting.
3. Remove control access panel.
4. Push in gas control knob slightly and turn clockwise
to “OFF.”
5. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the floor.
If you then smell gas, STOP! Follow “B” in the
safety information above. If you don’t smell gas,
go to the next step.
6. Open the pilot sight door above the main burners.
7. Find pilot – follow metal tube from the gas control.
The pilot is between the two burner tubes behind
the pilot sight door.
HV & HW USER’S INFORMATION MANUAL
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
A. The HW (constant pilot) appliance is equipped with
a continuous pilot it must be lit by hand. Follow the
lighting instructions exactly.
B. BEFORE LIGHTING smell all around the appliance
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use
any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
LIGHTING INSTRUCTIONS
• If you cannot reach your gas supplier, call the
fire department.
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, don’t try to repair it, call a
qualified service technician. Force or attempted
repair may result in a fire or explosion.
D. Do not use this appliance if any part has been
under water. Immediately call a qualified service
technician to inspect the appliance and to replace
any part of the control system and any gas control
which has been under water.
TO TURN OFF GAS TO APPLIANCE
1. Set the thermostat to lowest setting.
2. Remove control access panel.
3. Push in gas control knob slightly and turn
clockwise to “OFF.” Do not force.
4. Replace control access panel.
Page 3
8. Turn knob on gas control
counterclockwise
to “PILOT.”
9. Push in control knob all the way
and hold in. Immediately
light the pilot with a match.
Continue to hold the control
knob in for about one (1)
minute after the pilot is lit.
Release knob and it will pop back up. Pilot should
remain lit. If it goes out, repeat steps 4 through 9.
• If knob does not pop up when released. Stop
and immediately call your service technician
or gas supplier.
• If the pilot will not stay lit after several tries.
Turn the gas control knob to “OFF” and call
your service technician or gas supplier.
10. Close pilot sight door.
11. Turn gas control knob counterclockwise
to “ON.”
12. Replace control access panel.
13. Set thermostat to desired setting.
Loading...