Hydrotech 785UF Quick Setup Manual

Page 1

785UF Valve Softener Quick Set Up Manual

Step 1 – Inspection

Check to make sure you got everything supplied by factory and there is no visible or concealed damage. In case of missing items, please contact customer service immediately and have the Product Serial # handy. (Product Serial # can be found at the back of the control valve, see below)

The items you will expect are:

1. Tank with Softener Media loaded

2. Control Valve

3. Parts Kit

4. Brine Tank (Round or Square ) and Components

3. Parts Kit

3/4” Elbow Fitting X 2

Product Serial #

Bypass Tool

Set of Injectors

1. Tank with Softener

Media loaded

Spill Cap

D-Tube

4. Brine Tank (Round or Square ) and Components

Brine Tank (Round or Square)

2. Control Valve

Brine Elbow

Bypass Test Port Clip X 2

Drain Hose Fitting

Drain Clip

Bypass

Bypass Cllips X 2

Brine Tank Tubing

1” Straight Fitting X 2

Upper Basket/ Strainer

Brine line Plug ((used for Filters))

Grease port Orings using brush (not included) or your finger (Make sure to wear protective gloves)

Set of Washers

Step 2 – Installing Valve to the Tank

Select a Installation location and make sure there is access to 110V power outlet and drain line. Lube the bottom Valve Orings with the grease supplied, Attach the Upper Basket. Unscrew the spill cap. Carefully Slide the D-Tube inside the Valve and Screw the Valve inside the Tank such that the power cord doesnt get caught between the valve and the tank. Make sure the D-Tube slides inside the valve.

Transformer

Grease Packet

Grid Legs (3 for Round and 4 for Square)

Grid (Round or Square)

Unscrew Spill Cap

D-Tube

Brine Well/ Safety Float

Brine Tank Lid

Attach Upper Basket

CAUTION: Make sure the power cord of the valve doesnt get caught between the threads

Page 2

Step 3 – Assembling Brine Tank

'

a. Attach the three brine grid legs to grid plate. The legs will snap on to the tabs of the salt plate making a “click” sound. For square brine tank there are four legs.

b. Insert the brine well assembly inside the grid plate as well below.

c. Drop the brine grid with brine well inside the brine tank such that the nut fitting

faces the hole on the brine tank. Then press the grid evenly inside the brine tank until the brine grid legs touches the bottom of the brine tank.

d. Take the brine tube and insert the nut and plastic sleeve as shown below.

Insert Sleeve

e. Insert the tube in the float assembly elbow and hand tighten the nut. In many cases the brine line already come installed from the factory. Leave the other end of the brine line tube inside the brine tank

f. For installation of brine tank at the installation site, pull the other end of the brine tube from the hole on the brine tank. The completed assembly is shown below.

IMPORTANT: IN ROUND BRINE TANK, IT IS IMPORTANT TO ALIGN THE HANDLE TO THE BRINE WELL AS SHOWN

The hole in the brine tank should line up with the brine line as shown for round and square brine tank.

Step 5 – Power and Program Valve

Key Pad Conguration

SETTINGS This function is to enter the basic set up information required at the time of installation.

MANUAL This function is to initiate an immediate or delayed manual REGEN regeneration.

DOWN / Increase or decrease the value of the settings while in the UP programming mode.

6(77,1*60$18$/

5(*(1

2:1

Hole

Settings Press SETTINGS key (3 SECONDS / BEEP)

TIME OF DAY

12:01 PM

Press SETTINGS key

MONTH

AUGUST

Press SETTINGS key

YEAR

2016

DAY

Step 4 – Attaching Brine Tubing to the Valve

Put insert inside the brine tubing

SALT SETTING

Press SETTINGS key

SET HARDNESS

20 GRAINS

Press SETTINGS key

SET PEOPLE

Press SETTINGS key

SALT SETTING

HIGH EFFICIENCY

STANDARD

IRON & MN

Press SETTINGS key

WATER TYPE

MUNICIPAL

WELL / OTHER

Press SETTINGS key

REGEN TIME

2:00 AM

Press SETTINGS key

PROGRAMMING

COMPLETE

Choose HIGH EFFICIENCY to minimize salt usage. Your system will regenerate a little more often but your salt usage can be reduced by 20% compared to the STANDARD setting. Choose STANDARD when you need to maximize your capacity but still operate the system with good efficiency. Choose IRON & MN if you have problem water containing these minerals. The high salt setting will be needed since these minerals are more difficult to clean out of the resin bed. Note: A resin cleaner will also need to periodically added to the brine tank to insure proper operation.

WATER TYPE

This setting will determine if the BACKWASH OVERIDE function will be on or off. Select MUNICIPAL if the water source is clean (<1NTU turbidity) and the system will skip the back wash cycle based on the setting in BACKWASH OVERIDE. Select WELL / OTHER if any Iron or Manganese is present or if the water source is not clean (< 1NTU turbidity). The system will back wash every time. his setting determines the time of day to perform a scheduled regeneration.

TOLL-FREE: 1-877-288-9888

Regina, SK • Cambridge, ON • Carmel, IN • Fridley, MN • Phoenix, AZ

www.hydrotechwater.com

Follow the Instruction Manual to Complete the Installation of the Product

55227 05/16