Hydra-Kool KPM-CG Operator’s Manual
DOE
Compliant
KPM SERIES - INSTALLATION AND OPERATION MANUAL - V0
MVP GROUP CORPORATION
5659 Royalmount Ave.
Montreal, QC, Canada
Telephone: (514) 737-9701
Toll Free Telephone: (888) 275-4538
Toll Free Fax: (877) 453-8832
Email: sales@mvpgroupcorp.com
Website: www.mvpgroupcorp.com
H4P 2P9
Fax: (514) 342-3854
2
1 General information 5
1.1 Case description 5
2 Getting started with your KFM series 15
2.1 Location 15
2.2 Uncrating 16
2.2.1 Front and sides assemblies 17
2.3 Check for damage 19
2.4 Control panel and main features 20
2.5 Check serial, model numbers and requested options 22
2.6 Warning/Caution labels 24
2.7 Check your electrical installation 28
2.8 Electrical, drain and refrigeration connections (remotes only) 28
2.9 Joining 29
2.10 Plugging and start 37
3 Refrigeration 39
3.1 Self contained refrigeration equipment and defrost 39
3.2 Refrigeration loads (remotes only) 41
INDEX
4 Electrical 41
4.1. Electrical specifications data 41
4.2. Electrical service receptacles (optional) 43
4.3. Electrical diagrams 44
4.4. Electronic controller 50
5 Maintenance 53
5.1 Exterior cleaning 53
5.2 Interior cleaning 54
5.3 Shelf removing 54
5.4 Back Sliding doors removal 55
5.5 Light substitution 56
5.6 Panels and protection grille removal 57
5.7 Condenser cleaning 57
5.8 Evaporator cleaning 58
5.9 Evap Pan cleaning 58
5.10 Drain inspection 59
5.11 Glass type conversion model 59
6 Troubleshooting/Service 60
6.1 Troubleshooting 60
6.2 Service 61
7 Warranty 63
8 Notes 64
3
This page has been left blank intentionally.
4
1 General information
1.1 Case description
KPM series model (number) system.
KPM CG 40 S
AAA BB CC D
AAA
Basic model
BB
Model variation
|
CG-Curved glass tilt forward
|
FG-Flat glass tilt forward
|
OF-Open front
|
|
|
|
|
CC
Length
60''
80''
100''
D
Type of Unit.
|
S-Self Contained
|
R-Remote
|
D-Dry
|
5
KPM SERIES
KPM-CG-S(R)(D)
KPM-CG-S(R)(D)
6
KPM-FG-S(R)(D)
KPM-FG-S(R)(D)
7
KPM-OF-S(R)(D)
KPM-OF-S(R)(D)
8
Implantation
Drain outlet
Electrical board
Refrigeration piping
KPM-CG-xx-S
Front
9
10
Front
KPM-CG-xx-R
Drain outlet
Electrical board
Refrigeration piping
Front
KPM-FG-xx-S
11
Front
KPM-FG-xx-R
12
Drain outlet
Electrical board
Refrigeration piping
Electrical wiring
Front
KPM-OF-xx-S
13
Front
KPM-OF-xx-R
14
KPM series intended for deli, meat and fish are type 1 equipment - 75°F/55%RH.
Temperature of the deli and meat cases is set for 32°F.
The decks have a 31 lb/ft loading limit.
Glass shelves are for non refrigerated products only and have a 5,5 lb/ft loading limit.
Model
KPM-CG-60-S(R)(D)
KPM-CG-80-S(R)(D)
KPM-CG-100-S(R)(D)
KPM-FG-60-S(R)(D)
KPM-FG-80-S(R)(D)
KPM-FG-100-S(R)(D)
KPM-OF-60-S(R)(D)
KPM-OF-80-S(R)(D)
KPM-OF-100-S(R)(D)
2 Getting started with your KPM series
2.1 Location
To your new equipment perform well please respect the following warnings:
This is type 1 equipment, intended to work with 75°F / 55%RH.
This equipment is intended for maintaining temperature only.
Be sure products are not ambient temperature (must be cold)
This equipment must be located in an indoor environment.
Check for airdrafts and avoid them.
Air movement from ac units shouldn’t be directed to the equipment.
Dimensions
(LxDxH in inches)
601'' x 49'' x 61''
|
77'' x 49'' x 61''
|
101'' x 49'' x 61''
|
60'' x 441'' x 61''
|
77'' x 441'' x 61''
|
101'' x 441'' x 61''
|
60'' x 3411'' x 61''
|
77'' x 3411'' x 61''
|
101'' x 3411'' x 61''
|
Service
dimensions
(LxDxH in inches)
601'' x 49'' x 75''
|
77'' x 49'' x 75''
|
101'' x 49'' x 75''
|
601'' x 441'' x 82''
|
77'' x 441'' x 82''
|
101'' x 441'' x 82''
|
601'' x 3411'' x 6211''
|
77'' x 3411'' x 6211''
|
101'' x 3411'' x 6211''
|
Volume (ft³)
9,3/5,33
|
12,1/8,76
|
16,0/13,41
|
9,3/5,33
|
12,1/8,76
|
16,0/13,41
|
9,3/5,33
|
12,1/8,76
|
16,0/13,41
|
The equipment must not be directly or indirectly exposed to the sun.
Check for rejected heat from another refrigeration units and avoid that.
Place the equipment in a levelled floor.
Do not obstruct the air way in front of the condenser.
Make sure there is a drain preparation (remotes and fish display cases only).
15
Models to be positioned against a wall keep a safe distance of 2''.
After servicing always close the doors.
Make sure you have a suitable electrical installation.
This equipment should be handled by a qualified technician.
2.2 Uncrating
All operations must be done carefully.
All plastic protective films must be removed before using the equipment for
the first time.
1
3
2
4
16
2.2.1 Front and sides assemblies
2x - VID24M01095
1x - BRA09M02000
1x - PRN00101002
DIN 916
6 x - CMS00101000
2x - VID07003000 1x - PRT01201190
2x - PAR00802002
DIN912 M5x12
1x - APO01101000 1x - PAR00902001
10 x - PAR11101001 1x - GAM13M01200
2x - ANL00101006
DIN 127
DIN7380 M5x12
2x- ANL00501006
DIN 9021
1x - PAR00902004
DIN7380 M4x10
4x - POR19M01100
2x - SUP17M01020
1x - PAR01002013 1x - PRT01301190
17
1
2
3
5
4
6
18
7 8
2.3 Check for damage
At the end of production HYDRA KOOL products are carefully inspected. No damaged
units are sent out.
HYDRA KOOL doesn’t take responsibility for damage between factory and client.
Possible damage on the unit must be checked to file a claim near the transportation
company.
The unit must be checked in the following points:
Exterior panels
Doors
Shelves
Glasses
Paint job
Door handles
Base structure
19
2.4 Control panel and main features
The pictures below, shows the main features and all necessary controls.
Electronic controller
Light switch
Power signal
Condensing unit switch
Hot key connector
Electrical board
Self contained control panel (KPM-CG/FG/OF)
Electronic controller
Light switch
Power signal
Condensing unit switch
20
Electrical board
Remote control panel (KPM-CG/FG/OF)
Light switch
Power signal
Power switch
Electrical board
Dry control panel (KPM-CG/FG/OF)
21
Loading...