THIS SPECIFICATION IS THE PROPERTY OF HYDIS AND SHALL NOT BE
REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF
HYDIS AND MUST BE RETURNED TO HYDIS UPON ITS REQUEST
TITLE : HV121WX4-110
Product Specification
www.panelook.com
PROPRIETARY NOTE
Rev. A
HYDIS Technologies
SPEC. NUMBER
S864-1342
B2005-C001-D(1/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PRODUCT GROUP
TFT-LCD PRODUCTS
REV.
A
ISSUE DATE
2009. 02. 10
A4(210 X 297)
www.panelook.com
PAGE
PAGE
1 OF 30
Page 2
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT-LCD PRODUCT
REV
h
ISSUE DATE
2009.02.10
REVISION HISTORY
REV.ECN NO.DESCRIPTION OF CHANGES DATE PREPARED
OInitial Release07.10.30Joseph Ha
AE0902-F003CI Logo Change (HYDIS)09.02.10S.T. KO
SPEC. NUMBER
S864-1342
B2005-C001-D(2/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
SPEC. TITLE
HV121WX4-110 Product Specification
www.panelook.com
PAGE
3 OF 30
Page 4
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT-LCD PRODUCT
yl}
h
1.0 GENERAL DESCRIPTION
1.1 Introduction
HV121WX4-110 is a color active matrix TFT LCD module using amorphous silicon TFT's
(Thin Film Transistors) as an active switching devices. This module has a 12.1 inch
diagonally measured active area with WXGA resolutions (1280 horizontal by 800 vertical
pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in
vertical stripe and this module can display 262,144 colors. The TFT-LCD panel used for
this module is a low reflection and higher color type.
LVDS
Input
Signal
Connector (CN
LVDS Rx
+
T/CON
Gate Driver
Source Driver
TFT LCD Panel
pzz|lGkh{l
2009.02.10
VDD
1
) .
DC/DC
Gamma
Vcom
BACK LIGHT (Fluorescent Lamp)
1.2 Features
z Thin and light weight
z 3.3 V power supply
z Low driving voltage and low power consumption
z 1 Channel LVDS Interface
z Single CCFL (Bottom side/Horizontal Direction)
z 262,144 colors
z Data enable signal mode
z Side Mounting Frame
z On Board EDID chip
z RoHS Product
z VESA V2 Compatible except for thickness
z Anti-Reflection polarizer product for sunlight readability
1280 Ý800
CN2
SPEC. NUMBER
S864-1342
SPEC. TITLE
HV121WX4-110 Product Specification
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
PAGE
4 OF 30
Page 5
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT-LCD PRODUCT
yl}
h
pzz|lGkh{l
1.3 Application
z Tablet PC
1.4 General Specifications
<Table 1. General Specifications>
ParameterSpecificationUnitRemarks
Active area 261.12 (H) ശ163.20 (V)mm
Number of pixels 1280 (H) ശ800 (V)pixels
Pixel pitch 0.204 (H) ശ0.204 (V)mm
Pixel arrangementRGB Vertical stripe
Display colors262,144colors
2009.02.10
Display modeNormally Black
Dimensional
outline
Luminance of
White
Weight290 (Typ.) / 300 (Max.) g
EBL3.0 (Typ.)WAt 60nit
Back-lightCCFL, Horizontal-lamp typeNote 1
275.8r0.5(W) ശ178.0r0.5(V) ശ 6.4 Typ D (6.7 Max)
200 (Typ.)Cd/m²at 5points
mm
Note 1: CCFL (Cold Cathode Fluorescent Lamp)
SPEC. NUMBER
S864-1342
SPEC. TITLE
HV121WX4-110 Product Specification
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
PAGE
5 OF 30
Page 6
Global LCD Panel Exchange Center
W
YW[W]W_WTYW
YW
[W
]W
_W
XW W
v Gy
z Gy
yGoGOLyoP
{ GOȋjP
www.panelook.com
PRODUCT GROUP
TFT-LCD PRODUCT
yl}
h
2.0 ABSOLUTE MAXIMUM RATINGS
The followings are maximum values which, if exceed, may cause faulty operation or
damage to the unit.
< Table 2. Absolute Maximum Ratings>
ParameterSymbolMin.Max.UnitRemarks
Logic Power SupplyV
Logic Input VoltageV
DD
IN
Back-light Lamp CurrentIBL2.07.0mA
Back-light FrequencyFBL4580KHz
Operating TemperatureT
Storage TemperatureT
OP
SP
VSS-0.34.0VTa = 25 ധ2 ଇ
VSS-0.3VDD+0.3V
0+50
-20+60
ଇ
ଇ
pzz|lGkh{l
2009.02.10
Note 1
Note 1. Temperature and relative humidity range are shown in the figure below.
* 90 [%] RH Max. (40ଇೈTa)
* Maximum wet-bulb temperature at 39 ଇ or less. (Ta40ଇ) No condensation
`W
\
(40,90)
(50,50)
(60,27)
SPEC. NUMBER
S864-1342
SPEC. TITLE
HV121WX4-110 Product Specification
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
PAGE
6 OF 30
Page 7
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT-LCD PRODUCT
yl}
h
3.0 ELECTRICAL SPECIFICATIONS
3.1 Electrical Specifications
< Table 3. Electrical specifications >
ParameterMin.Typ.Max.UnitRemarks
Power Supply VoltageV
Power Supply CurrentI
DD
DD
CCFL Ignition Timet1sec
High Level Differential Input Signal
Voltage
Low Level Differential Input Signal
Voltage
Back-light Lamp VoltageV
Back-light Lamp CurrentI
Back-light Lamp operating
Frequency
V
IH
V
IL
BL
BL
F
L
Lamp Start Voltage
Lamp Life10,00015,000Hrs
P
D
Extended Battery Life
Power Consumption
Notes : 1. The supply voltage is measured and specified at the interface connector of LCM.
The current draw and power consumption specified is for 3.3V at 25.
a) Typ: Windows XP desktop Pattern b) Max: V2 Skip Pattern
2. Reference value, which is measured with Samsung Electric SIC-180 Inverter.
(VBL Min is value at IBL Min and VBL Max is value at IBL Max)
3. The lamp frequency should be selected as different as possible from the horizontal synchronous
frequency and its harmonics to avoid interference which may cause line flow on the display.
4. For starting the backlight unit, the output voltage of DC/AC's transformer should be larger than
the minimum lamp starting voltage.(1,120 Vrms at 25 & 1,350 Vrms at 0 )
If an inverter has shutdown function it should keep its output for more than 1 second even if
the lamp connector open. Otherwise the lamps may not to be turned on.
5. End of Life shall be determined by the time when any of the following is satisfied under continuous
lighting at 25 and IBL = 7.0[mA].
ଝy Intensity drops to 50% of the Initial Value.
6. Calculated value for reference (VBL Ý IBL)
P
BL
P
total
P
D
P
BL
P
total
3.03.33.6V
330mA
-+100mV
-100-mV
760580540V
2.06.07.0mA
4580KHz
1,120V
1,350V
1.0W
2.0W
3.0W
1.1W
3.53.85W
4.6W
rms
rms
rms
pzz|lGkh{l
2009.02.10
[Ta = 25ρ2ఁ]
Note1
Note1
Note2
One Lamp, Note3
At Ta=25ଇ, Note4
At Ta=0ଇ, Note4
IBL= 7mA, Note5
At Mosaic pattern
At 60nit
Note1
IBL=6mA, Note6
SPEC. NUMBER
S864-1342
SPEC. TITLE
HV121WX4-110 Product Specification
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
PAGE
7 OF 30
Page 8
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT-LCD PRODUCT
yl}
h
pzz|lGkh{l
2009.02.10
4.0 OPTICAL SPECIFICATION
4.1 Overview
The test of Optical specifications shall be measured in a dark room (ambient luminance d 1 lux and
temperature = 25r2ଇ) with the equipment of Luminance meter system (Goniometer system and TOPCONE
BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing
angle of ഘ and equal to 0q. We refer to ഘ
) as the 12 o’clock direction (“upward”), ഘ
ഘ
12
ഘ
spot on the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to
measurement... VDD shall be 3.3+/- 0.3V at 25qC. Optimum viewing angle direction is 6 o’clock.
(= ഘ6) as the 6 o’clock direction (“bottom”). While scanning ഘand/or Ø, the center of the measuring
Ø=270
4.2 Optical Specifications
<Table 4. Optical Specifications>
ParameterSymbolConditionMin.Typ.Max.UnitRemark
ԭ
ԭ
ԭ
ԭ
3
9
12
6
Viewing
Horizontal
Angle
range
Vertical
Luminance Contrast ratioCR
(=ഘ3) as the 3 o’clock direction (the “right”), ഘ
Ø=0
(= ഘ9) as the 9 o’clock direction (“left”) and
Ø=180
8990Deg.
8990Deg.Note 1
CR > 10
8990Deg.
8990Deg.
ԭ = 0q
400500Note 2
Ø=90
(=
Luminance
of White
White
5 PointsY
5 PointsY58085
Luminance
uniformity
13 PointsY136575
White Chromaticity
Redx
Reproduction
Greenx
Of color
Bluex
ResponseRise T
TimeDecayT
Cross TalkCT
w
170200cd/m
2
ԭ = 0q
IBL = 6mA
%Note 3
x
w
y
w
R
y
R
G
y
G
B
y
B
r
ԭ = 0q
ԭ = 0q
Ta= 25q C
ԭ = 0q
d
ԭ = 0q
0.2830.3130.343Note 4
0.2990.3290.359
0.5540.5840.614
0.3100.3400.370
0.2720.3020.332
0.5230.5530.583
0.1160.1460.176
0.1110.1410.171
28msNote 5
2.0%Note 6
SPEC. NUMBER
S864-1342
SPEC. TITLE
HV121WX4-110 Product Specification
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
PAGE
8 OF 30
Page 9
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT-LCD PRODUCT
yl}
h
Note :
1.Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are
determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock
direction with respect to the optical axis which is normal to the LCD surface (see FIGURE
1 shown in Appendix).
2.Contrast measurements shall be made at viewing angle of ԭ= 0q and at the center of
the LCD surface. Luminance shall be measured with all pixels in the view field set first to
white, then to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance
Contrast Ratio (CR) is defined mathematically.
Luminance when displaying a white raster
CR =
Luminance when displaying a black raster
3.The White luminance uniformity on LCD surface is then expressed. (See FIGURE 2 shown
in Appendix).
pzz|lGkh{l
2009.02.10
Uniformity
ԩY=
4.The color chromaticity coordinates specified in Table 4 shall be calculated from the
spectral data measured with all pixels first in red, green, blue and white. Measurements
shall be made at the center of the panel.
5.The electro-optical response time measurements shall be made as FIGURE 3 shown in
Appendix by switching the “data” input signal OFF and ON. The times needed for the
luminance to change from 10% to 90% is Tr, and 90% to 10% is Td.
6.Cross-Talk of one area of the LCD surface by another shall be measured by comparing
the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level,
to the luminance (YB) of that same area when any adjacent area is driven dark. (See
FIGURE 4 shown in Appendix).
Minimum Luminance of 5(or 13) points
X 100 (%)
Maximum Luminance of 5(or 13) points
SPEC. NUMBER
S864-1342
SPEC. TITLE
HV121WX4-110 Product Specification
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
PAGE
9 OF 30
Page 10
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT-LCD PRODUCT
5.0INTERFACE CONNECTION.
5.1 Electrical Interface Connection
<Table 5. Pin Assignments for the Interface Connector>
CN1Interface connectorHirose/DF19KR-20P-1H or equivalent
User side connectorHirose/DF19G-20S-1C or equivalent
wGuzmy
1VSSGround
2VDD1Power Supply: +3.3V
3VDD2Power Supply: +3.3V
4Vdd_EDIDEDID +3.3V
yl}
h
pzz|lGkh{l
2009.02.10
5NCReserved
6Clk_EDIDEDID Clk
7Clk_DataEDID Data
8RIN0-LVDS Negative data signal (-)Tx pin # 48
9RIN0+LVDS Positive data signal (+)Tx pin # 47
10VSSGround
11RIN1-LVDS Negative data signal (-)Tx pin # 46
12RIN1+LVDS Positive data signal (+)Tx pin # 45
13VSSGround
14RIN2-LVDS Negative data signal (-)Tx pin # 42
15RIN2+LVDS Positive data signal (+)Tx pin # 41
16VSSGround
17RCLKIN-LVDS Negative clock signal (-)Tx pin # 40
18RCLKIN+LVDS Positive clock signal (+)Tx pin # 39
19VSSGround
20VSSGround
SPEC. NUMBER
S864-1342
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
SPEC. TITLE
HV121WX4-110 Product Specification
10 OF 30
www.panelook.com
PAGE
Page 11
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT-LCD PRODUCT
5.2. Back-light Interface
CN2Interface Connector•: BHSR-02VS-1 (JST) or equivalent
Each color is displayed in sixty-four gray scales from a 6 bit data signal input. A total of 262,144
colors are derived from the resultant 18 bit data.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
PAGE
Page 16
Global LCD Panel Exchange Center
www.panelook.com
9.0 POWER SEQUENCE
To prevent a latch-up or DC operation of the LCD module, the power on/off
sequence shall be as shown in below
0.9VDD
Power Supply
Interface Signal
0.1VDD
0V
0V
PRODUCT GROUP
TFT-LCD PRODUCT
T1
T2
Valid
0.9VDD
T5
yl}
h
0.1VDD
T7
T6
pzz|lGkh{l
2009.02.10
T3T4
Back- light
0V
z 0 < T1 d 10 ms
z 0 < T2 d 50 ms
z 200 ms d T3
z 200 ms d T4
z 0 d T5 d 50ms
z 0 d T6 d 10ms
z 500ms d T7
Notes:
1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep
high impedance.
2. Do not keep the interface signal high impedance when power is on.
3. Back Light must be turn on after power for logic and interface signal are valid.
SPEC. NUMBER
S864-1342
SPEC. TITLE
HV121WX4-110 Product Specification
16 OF 30
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
PAGE
Page 17
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT-LCD PRODUCT
10.0 MECHANICAL CHARACTERISTICS
10.1 Dimensional Requirements
FIGURE 5, 6 shown in appendix shows mechanical outlines for the model.
ParameterSpecificationUnit
Active area 261.12 (H) ശ163.20 (V)
Number of pixels 1280(H) ശ800(V)
(1 pixel = R + G + B dots)
Pixel pitch 0.204(H) ശ0.204(V)
Pixel arrangementRGB Vertical stripe
Display colors262,144
Display modeNormally Black
yl}
h
pzz|lGkh{l
2009.02.10
mm
pixels
mm
colors
Dimensional outline
Weight290 (Typ.) / 300 (Max.)
Back-lightCCFL, Horizontal-lamp type
275.8r0.5(W) ശ178.0r0.5(V) ശ 6.4 Typ D (6.7 Max)
10.2 Mounting
See FIGURE 5. (shown in Appendix)
10.3 Anti-Reflection Polarizer.
The surface of the LCD has an anti-reflection coating to minimize reflection
for sunlight readability.
10.4 Light Leakage
There shall not be visible light from the back-lighting system around the edges of the
screen as seen from a distance 50 cm from the screen with an overhead light level of
150lux. The manufacture shall furnish limit samples of the panel showing the light
leakage acceptable.
mm
g
SPEC. NUMBER
S864-1342
SPEC. TITLE
HV121WX4-110 Product Specification
17 OF 30
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
PAGE
Page 18
Global LCD Panel Exchange Center
www.panelook.com
11.0 RELIABLITY TEST
NoTest ItemsConditions
1High temperature storage test
2Low temperature storage test
High temperature & high
3
humidity operation test
4High temperature operation test
5Low temperature operation test
6Thermal shock
PRODUCT GROUP
TFT-LCD PRODUCT
Ta = 60 qC, 240 hrs
Ta = -20 qC, 240 hrs
Ta = 50 ଇ, 80%RH, 240hrs
Ta = 50 qC, 240 hrs
Ta = 0 qC, 240 hrs
Ta = -20 qC l 60 qC (30 min), 100 cycle
yl}
h
pzz|lGkh{l
2009.02.10
Vibration test
7
(non-operating)
Shock test
8
(non-operating)
Electro-Static Discharge Test
9
(non-operating)
Frequency : 10~500Hz
Gravity/AMP : 1.5G
Period : X,Y,Z 30min
Gravity : 220G
Pulse width : 2ms, half sine wave
ρX, ρY, ρZ Once for each direction
Air : 150pF, 330ohm, 15KV
Contact : 150pF, 330ohm, 8KV
SPEC. NUMBER
S864-1342
SPEC. TITLE
HV121WX4-110 Product Specification
18 OF 30
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
PAGE
Page 19
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT-LCD PRODUCT
yl}
h
pzz|lGkh{l
2009.02.10
12.0 HANDLING & CAUTIONS
12.1 Cautions when taking out the module
y Pick the pouch only, when taking out module from a shipping package.
12.2 Cautions for handling the module
y As the electrostatic discharges may break the LCD module, handle the LCD module
with care. Peel a protection sheet off from the LCD panel surface as slowly as possible.
y As the LCD panel and backlight element are made from fragile glass material, impulse
and pressure to the LCD module should be avoided.
y As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth
without chemicals for cleaning.
y Do not pull the interface connector in or out while the LCD module is operating.
y Put the module display side down on a flat horizontal plane.
y Handle connectors and cables with care.
12.3 Cautions for the operation
y When the module is operating, do not lose MCLK, DE signals. If any one of these
signals were lost, the LCD panel would be damaged.
y Obey the supply voltage sequence. If wrong sequence were applied, the module would
be damaged.
12.4 Cautions for the atmosphere
y Dewdrop atmosphere should be avoided.
y Do not store and/or operate the LCD module in a high temperature and/or humidity
atmosphere. Storage in an electro-conductive polymer-packing pouch and under
relatively low temperature atmosphere is recommended.
12.5 Cautions for the module characteristics
y Do not apply fixed pattern data signal to the LCD module at product aging.
y Applying fixed pattern for a long time may cause image sticking.
12.6 Other cautions
y Do not disassemble and/or re-assemble LCD module.
y Do not re-adjust variable resistor or switch etc.
y When returning the module for repair or etc, please pack the module not to be broken.
We recommend using the original shipping packages.
SPEC. NUMBER
S864-1342
SPEC. TITLE
HV121WX4-110 Product Specification
PAGE
19 OF 30
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 20
Global LCD Panel Exchange Center
www.panelook.com
13.0 PACKING
13.1 Packing Order
Put Pad into the box.
PRODUCT GROUP
TFT-LCD PRODUCT
Put silica gels in the
box.
yl}
h
pzz|lGkh{l
2009.02.10
After sealing the box,
attach Packing Label
on the attach position
sign area of the box.
Place a cover on the
top of the box.
Notes
y Box Dimension: 261mm(W) X 349mm(D) X 311mm(H)
y Package Quantity in one Box: 10pcs
As shown in the figure,
place the Modules
bundled by shielding bag
in the box.
SPEC. NUMBER
S864-1342
SPEC. TITLE
HV121WX4-110 Product Specification
20 OF 30
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
PAGE
Page 21
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
14.0 Environment & Safety
14.1 Packing Label
Label Size: 108 mm (L) u 56 mm (W)
Contents
Model: HV121WX4-110
Q`ty: Module Q`ty in one box
Serial No.: Box Serial No. See next figure for detail
description.
Date: Packing Date
FG Code: FG Code of Product
TFT-LCD PRODUCT
yl}
h
pzz|lGkh{l
2009.02.10
MODEL : HV121WX4-110
SERIAL NO. : 0000000000000
0000000000000
Type Grade Year Month ITEM-CODE Serial_no
Q’TY : 10
DATE : XXXX. XX. XX
14.2 Mercury disposal & High voltage caution
FG CODE
RoHS Mark
SPEC. NUMBER
S864-1342
SPEC. TITLE
HV121WX4-110 Product Specification
21 OF 26
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
PAGE
Page 22
Global LCD Panel Exchange Center
o}XYX~[TXXW
www.panelook.com
14.3 Product Label
4
3
HYDIS Barcode
12
PRODUCT GROUP
TFT-LCD PRODUCT
3
4
5
yl}
h
6
pzz|lGkh{l
2009.02.10
7
No 1. Control Number
No 2. Rank / Grade
No 3. Line Classification
(HYDIS : H)
No 4. Year (5 : 2005, 6 : 2006, …)
XXXXXXXXXXXXXXXXX
No 5. Month (1, 2, 3,…, 9, X, Y, Z)
No 6. FG Code
No 7. Serial Number
SPEC. NUMBER
S864-1342
SPEC. TITLE
HV121WX4-110 Product Specification
22 OF 30
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
PAGE
Page 23
Global LCD Panel Exchange Center
Y
YWW
[WW
]WW
ZYW
X
\
[
][W`]W
aGG{Gw
s
w
[`
^\X
[`
XYZX
]^_
Z
`XW
XXXYXZ
www.panelook.com
15.0 APPENDIX
Figure 1. Measurement Set Up
PRODUCT GROUP
TFT-LCD PRODUCT
yl}
h
OsGdG\W PG
pzz|lGkh{l
2009.02.10
Figure 2. Average Luminance Measurement Locations & Uniformity Measurement Locations
SPEC. NUMBER
S864-1342
SPEC. TITLE
HV121WX4-110 Product Specification
23 OF 30
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
PAGE
Page 24
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT-LCD PRODUCT
Figure 3. Response Time Testing
Tr
100%
90%
10%
0%
Figure 4. Cross Modulation Test Description
yl}
h
TFT Off (Black)TFT On (White)TFT Off (Black)
Td
pzz|lGkh{l
2009.02.10
Time
VIEW AREA
YA (1120, 400)
Cross-Talk =
320, 200
320, 600
YB - YA
YA
VIEW AREA
960,200
960,600
YB (1120,400)
ϧ 100
Where:
YA= Initial luminance of measured area (cd/m2)
YB= Subsequent luminance of measured area (cd/m2)
The location measured will be exactly the same in both patterns.
SPEC. NUMBER
S864-1342
SPEC. TITLE
HV121WX4-110 Product Specification
24 OF 30
B2005-C001-D(3/3)A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!