C20 Smart Charger
User Manual
C20 Smart Charger User Manual
Shanghai HYCO Genyong Technology Co., Ltd.
Disclaimer
Please read all the contents of the manual carefully before using the
products described in this manual to ensure the safe and effective use of
the product. Please keep this manual in a safe place for future use.
Do not disassemble the terminal by yourself or tear up the seal on the
terminal. Otherwise, Shanghai HYCO Genyong Technology Co., Ltd. will
not be responsible for the warranty or replacement of the terminal.
The pictures in this manual are for reference only. If there are individual
pictures that do not match the actual products, please refer to the actual
products. For the improvement and update of this product, Shanghai
HYCO Genyong Technology Co., Ltd. reserves the right to modify the
documentation at any time without prior notice.
All information contained in this manual is protected by copyright.
Shanghai HYCO Genyong Technology Co., Ltd. reserves all rights.
Without any written permission, no unit or individual may extract any
form or part of this document in any form or copy or bundle and use
with other products.
The products described in this manual may include Shanghai HYCO
Genyong Technology Co., Ltd. or third party copyrighted software. Unless
authorized by the relevant right holder, no unit or individual may copy or
distribute the above software in any form, e.g. modification, excerpt,
decompilation, disassembly, decryption, reverse engineering, leasing,
transfer, sublicense, and other infringement of software copyright.
Shanghai HYCO Genyong Technology Co., Ltd. has the final right to
interpret this statement.
Website：http://www.hycoglobal.com
C20 Smart Charger User Manual
Appearance
Indicator light
Ring scanner charging groove
C20 charger
Micro USB charging port
Barcode for disconnect bluetooth
C20 Smart Charger User Manual
User manual
Ring scanner
C20 charger
USB cable
Indicator light
Push the ring strap
to the bottom of
the slot
Ring scanner
Ring strap
Charging
Contact
Barcode for disconnect bluetooth
C20 Smart Charger User Manual
How to charge:
1. Connect the adapter with C20 charger, and connect the adapter to power.
2. When it is not in charging, the indicator light on the charger keeps green.
3. Put the ring scanner into the bottom of each charging slot with the scan
window upward. Please note the power contacts between the ring and cradle
must be touched, and the ring strap must be pushed to the end of slot.
4. When the indicator light turns red, it indicates the ring scanner is in charging.
When the indicator light turns green, it means charging finished.
5. If you need to disconnect the ring scanner with the device connected before,
please scan the barcode on the middle of the C20 charger.
Components
Item
Quantity
Usage
Charger
One
Support 10 sets of
ring scanners in one
charging cycle
USB Cable
One
Connection between
power and charger
5V2A Adapter
One
To connect the power
Certificate
One
Factory certificate
User manual
One
User manual
C20 Smart Charger User Manual
Specifications
L*W*H（MM）
266.5*151.4*36.7
Weight（KG）
1.02
Working temperature
-10°C~50°C
Charging grooves
quantity
10 Pcs
Bluetooth
BT4.2, BLE
Charging port
Micro USB
Machine electrical
parameters
Rated input voltage：5V
Rated input current：2A
Charging indicator
light
In charging: static red
Charging finished: static green
Notice
1. Check the ground connection safety before using.
2. Do not spray any liquid onto the charger.
3. If the charger will not be used, please pull out the power adapter.
C20 Smart Charger User Manual
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Any changes or modifications not expressly approved by the party responsible for
compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be
installed and operated with minimum distance between 20cm the radiator your body: Use
only the supplied antenna.
C20 Smart Charger User Manual
Manufacturer's Name: Shanghai Hyco Genyong Technology Co., Ltd.
Sample Description: Smart Charger
Trade Mark: HYCO
Model number: C20
Operating Temperature: ‐10° C to 35° C
This product is a fixed location. To comply with RF exposure requirements, a minimum
separation distance of 20cm must be maintained between the user’s
body and the device, including the antenna. Use only the supplied or an approved antenna.
This device in compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EU. All essential radio test suites have been carried out.
1. CAUTION : RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF
USED BATTERIES ACCORDING TO THE INSTRUCTIONS
2. The device complies with RF specifications when the device used at 20cm from your body
CE NB RF specification:
Function
Operation Frequency
Max RF
Outputpower
(dBm)
Limit
(dBm)
BLE
2402-2480MHz
6.11
20
This product can be used across EU member states
Loading...