W26
Ring Scanner
User Manual
Ring Scanner User Manual
1
Disclaimer
Disclaimer @ 2018 Shanghai Hyco Genyong Technology Co., Ltd. All rights reserved.
Please read through the manual carefully before using the product and operate it
according to the manual. It is advised that you should keep this manual for future
reference.
Do not disassemble the device or remove the seal label from the device. Otherwise,
Shanghai Hyco Genyong Technology Co., Ltd. does not assume responsibility for the
warranty or replacement.
All pictures in this manual are for reference only and actual product may differ.
Regarding to the product modification and update, Shanghai Hyco Genyong
Technology Co., Ltd. reserves the right to make changes to any software or product
to improve reliability, function, or design at any time without notice. Besides, the
information contained herein is subject to change without prior notice.
The products depicted in this manual may include software copyrighted by Shanghai
Hyco Genyong Technology Co., Ltd. or a third party. The user, corporation or
individual, shall not duplicate, in whole or in part, distribute, modify, decompile,
disassemble, decode, reverse engineer, rent, transfer or sublicense such software
without prior written consent from the copyright holders.
This manual is copyrighted. No part of this publication may be reproduced or used in
any form without written permission from Hyco.
Shanghai Hyco Genyong Technology Co., Ltd. reserves the right to make final
interpretation of the statement above.
Shanghai Hyco Genyong Technology Co., Ltd.
Ring Scanner User Manual
2
Design
Ring Scanner
Wearing: wear on index finger on left or right hand
Scanning: touch either side of ring body with thumb finger
to trigger the scanning
Ring Cradle（Bluetooth Receiver）
Ring Scanner User Manual
3
Charging
1. Charging ring scanner
Charging Illustration 1
Charging Illustration 2
Connect the ring cradle to power, click the ring scanner into
the bottom of cradle with the scan window upward. Please
Ring Scanner User Manual
4
note the power contacts of the ring and cradle must be
touched.
The red light indicates it is in charging, when the green light
turns on, it’s finished charging.
Warning: don't look straightly into the scan window when
scanning in case of laser harm to eyes.
2. Take the ring scanner out of the cradle
Hold the middle of the ring scanner gently and pull out upward
from the cradle.
Bluetooth connection
Connect with PC:
Firstly, connect the charging cradle with computer via USB
cable, the green light on the cradle turns on. Secondly, after
15 seconds, ring scanner scans the "Bluetooth connection"
barcode on the front of cradle, the blue light on the cradle
indicates the Bluetooth communication between ring
scanner and cradle is successfully set up.
Ring Scanner User Manual
5
Connect with Tablet PC or phone:
Enter the “ Setting ” in the Tablet PC or phone, click
"Bluetooth search", find the Bluetooth serial number of the
ring scanner, choose the corresponding Bluetooth serial
number in the searching list. When the ring light turns on
green, it indicates successful Bluetooth connection between
ring and Tablet PC or phone.
Remark: ring scanner is the slave, and terminal device is the
master
Use of applications (APP):
Prerequisites before connecting ring with different devices:
Ring Scanner User Manual
6
Change connection with different masters among computer,
Tablet PC and phone.
When ring pairs with different terminal devices, user needs to
scan different barcode before Bluetooth connection.
To connect ring scanner with computer, please scan the
barcode “COMMON”, but it is set by default.
To connect ring scanner with Smart Phone or Tablet PC based
on IOS system, please scan the barcode "IOS".
To connect ring scanner with Smart Phone or Tablet PC based
on Android system, please scan the barcode "ANDROID".
Ring Scanner User Manual
7
To connect ring scanner with Smart Phone or Tablet PC based
on Windows system, please scan the barcode "WINDOWS".
Components
Ring Scanner User Manual
8
Specifications
Ring Scanner User Manual
9
Functions
1. Scanning
Wear on left or right index finger, touch left or right side of ring
and aim at the barcode, the ring light turns green, it starts to
scan.
2. Ring Straps
Firstly, straightly pull out ring strap from the slot, then choose
another ring strap and push it to the top of slot.
3. Ring Indicator
The green light indicates successful scanning.
Ring Scanner User Manual
10
The red light flashing indicates low battery.
The green light keeping on for 1 second indicates successful
Bluetooth connection.
The blue light keeping on for 1 second indicates Bluetooth
disconnection.
The red, green and blue light flashing indicates restarting.
4.Bluetooth can’t connect
Normally, if the Bluetooth light doesn ’ t turn on, user can
scan the barcode "Reset Bluetooth Name", wait for 10 seconds,
and reconnect.
Scan the barcode “ Restore factory settings ” , the ring will
disconnect Bluetooth connection with terminal devices, and all
Ring Scanner User Manual
11
the settings will change to factory default.
5. Charging cradle light indicator
6.Wake up ring in charging
The ring doesn ’ t work when in charging, while it could be
waked up by touching either side of ring three times.
7. Laser calibration
If laser length changes longer or shorter, please stop scanning,
touch ring for 4 seconds once and repeat several times to get it
right. If it’s still abnormal, please scan the barcode“Automatic
calibration”.
After scan the barcode “Automatic laser calibration”, the ring
Ring Scanner User Manual
12
turns on purple, put it on the table, wait for 15 seconds until
the purple light turns off. The ring laser is calibrated right and
functions normally.
SERVICE
1.Warranty: one year for ring scanner, half year for battery and
accessories.
2.Contact: junqi.zheng@hyco.cc
Notice
» The ring window must be kept clean. Improper usage will
breach the limited warranty clause.
» Avoid rough objects scratching the window.
» Remove stains from window by soft cloth.
» Do not spray any liquid onto the window.
» Use cleaning water to clean.
Ring Scanner User Manual
13
Function barcodes setup
Change function of scanning after scanning the following
barcodes:
"Device information" barcode includes device information (e.g.
serial number, version number, Bluetooth version information).
Scan function code “Vibration Open ” to activate vibration
function, Scan function code “ Vibration close ” to close
vibration function.
Ring Scanner User Manual
14
In HID mode, scan the barcode "Speed up data transmission
through ring cradle", it can accelerate the data transmission
speed between the cradle and computer; scan the barcode
"Slow down data transmission through ring cradle", it can slow
down the data transmission between the cradle and computer.
Scan the barcode “Triggered continuous scanning”, ring could
keep scanning when user keeps touching the ring.
If user wants to change to common scanning, scan the
Ring Scanner User Manual
15
“Manual Trigger Mode” bar code.
"Manual Trigger Mode" is set by default, user needs to touch
ring once to scan once.
After scan "Automatic interval scanning" bar code, ring could
automatically scan every 0.5 ~ 3 seconds without touching (2
seconds by default)
After scan "Automatic interval scanning-reduce" barcode, it can
expedite the scanning speed once by 0.5 second, the fastest
Ring Scanner User Manual
16
scanning speed is scanning once every 0.5 second.
After scan "Automatic interval scanning-increase" barcode, it
can slow down the scanning speed once by 0.5 second, the
slowest scanning speed is scanning once every 3 seconds.
Scan angle adjustment
According to different barcode length, user needs to change
laser length to achieve better scanning effect.
1、Scan “Laser calibration” barcode to activate the function,
the ring light turns white and begins to automatically and
intermittently scan.
Ring Scanner User Manual
17
2、After scan “Widen” barcode, the laser length becomes
long; after scan “short ” barcode, the scan angle becomes
short .
Note: do not extend or shorten more than 10 times one time.
3、Scan “Confirm” barcode, the ring light turns yellow and
white, the laser length is confirmed.
4、Scan “ Data generation ” barcode, the ring light turns
yellow and red, and then turns purple for a while. The laser
Ring Scanner User Manual
18
length is set successfully after the purple light turns off.
Common functional barcodes
To meet different needs for customers, there are some
functional barcodes used to meet the requirements for
different customers.
After scan “Add Enter” barcode, it can automatically move to
next line in the text field after each scanning. If user wants to
close the function, scan “Delete Enter” barcode.
Ring Scanner User Manual
19
After scan "Add the tab" barcode, it can automatically move to
next line in excel after each scanning. If user wants to close the
function, scan "Delete the tab" barcode.
Loading...