Page 1
Product Instruction Manual
Handyflow Undersink
HF05MVC
5L vented point of use water heater
Version 3.2 Jan 2015
V15.6/5
Page 2
2
Thank you for purchasing the Hyco Handyflow undersink water heater.
The unit comes pre-wired and complete with a vented mixer tap and
flexible hoses. The Handyflow is ideal for occasional use, light dishwashing
at a single kitchen sink in the workplace, for example portable buildings,
offices, shops, workshops, garages and other small commercial premises.
Please read and understand these instructions before commencing
installation, and leave them with the user when installation is complete.
1. Important safety points
•
The Electrical installation must be carried out by a qualified electrician in
accordance with the current edition of the I.E.E. Wiring Regulations.
•
This appliance must be earthed.
•
Means for electrical disconnection must be incorporated in the fixed wiring in
accordance with the wiring rules.
•
Only connect the appliance to a single phase supply with a mains voltage as
specified on the rating plate.
•
It is essential that only open outlet fittings are used so the unit is not pressurised
(vented mixer tap and hoses supplied).
•
Always fit the heater the correct way up (pipes should be at the top)
•
Use the lowest acceptable temperature setting to save energy and reduce lime scale.
•
Do not connect to power unless the unit is full of water – open hot outlet and
allow water to flow freely to clear air locks.
•
Do not switch power on if water or pipes could be frozen.
•
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall not be made
by children without supervision.
Page 3
3
2. Installation
Wall Mounting
The Handyflow is normally fitted immediately below the outlet to be supplied, but it
can be mounted above or to the side of the outlet provided it is vertical with the pipe
outlets at the top. The unit can either be placed directly on the floor or fixed to the
wall using the fixings provided.
Ensure the mounting surface is strong enough to support the Handyflow
including the weight of the water.
Plumbing connections
The hot and cold fittings are at the top of the unit. These connections are colour coded
(blue=cold, red=hot).
They are NOT interchangeable.
The diagram above shows a typical installation with the Hyco Vented mixer tap HFTAPQ.
•
All fittings are provided so connection can be made via 15mm compression fittings.
•
Please follow manufacturer’s instructions provided with the vented tap.
Tighten all connections
to prevent from leaking.
Page 4
Electrical
•
The Electrical installation must be carried out by a qualified electrician in
accordance with the current edition of the I.E.E. Wiring Regulations.
•
Only connect the appliance to a single phase supply with a mains voltage
as specified on the rating plate.
•
Means for electrical disconnection must be incorporated in the fixed wiring
in accordance with the wiring rules.
•
This unit is supplied pre-wired. If the cable needs replacing, it must be replaced
with a correctly rated cable and any work should be carried out by a competent
person.
•
In order to avoid a hazard due to inadvertent resetting of the thermal cut-out,
this appliance must not be supplied through an external switching device
such as a timer or connected to a circuit that is regularly switched on and
off by the utility.
The unit is fitted with an auto-reset thermal cut-out which will operate for
safety reasons in the event of the unit overheating. To reset the thermal
cut-out switch off the power to the unit and allow it to cool down. Ensure
the unit is full and then switch the unit back on. The thermal cut-out should
reset itself.
4
Page 5
3. Operation
Switch on power to the unit and select the desired temperature setting 1.
The indicator is lit when the element is on.
5
OFF
Frost protection. Element will switch on when water
t
emperature falls below 7°C
Heats water to approx 25°C
Economy position. Heats water to approx 55°C
Max temperature approx 80°C
Tighten all connections
to prevent from leaking.
400mm
Page 6
4. Specifications
Voltage 230v~50Hz
Power 2.0kW
Capacity 5L
IP Rating IP24
Weight 3.5kg
6
180mm
270mm
400mm
Page 7
5. Guarantee and service policy
This product is guaranteed against faulty materials and manufacture for a period of one
year from the date of purchase. Hyco will in its sole discretion replace, repair or refund
any faulty unit. Incorrect installation and failure to follow correct operating instructions
are excluded. Consequential costs such as labour charges or damage to surroundings
are expressly excluded.
7
Page 8
hyco.co.uk
Hyco Manufacturing Ltd
Normandy Court
Express Way
Castleford, WF10 5NR
T 01924 225 200
F 01924 225 210
E sales@hyco.co.uk
INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH THE
EUROPEAN DIRECTIVE 2002/96/E.
At the end of its working life this equipment must not be disposed of as household
waste. It must be taken to a local authority waste collection centre or to a dealer
providing this service. Disposing of electrical and electronic equipment separately
enables its components to be recovered and recycled to obtain significant savings in
energy and resources. In order to underline the duty to dispose of this equipment
separately, the product is marked with a crossed out dustbin.
Loading...