HY-CLOR Robo Works Installation and Operation Manual
INSTALLATION AND OPERATION MANUAL
HyClor Roboworks Manual.indd 1 25/06/13 10:41 AM
Quick start guide
1. Remove cleaner from packaging and place on a hard flat surface.
2. Unwind the attached electrical cable.
3. Place cleaner into shallow end of the pool.
4. Place controller within reach of the cleaner cable and a 240 volt power point.
5. Plug cleaner cable into the 2 pin plug port on control module.
6. Plug the control module into the power supply socket.
7. Press the start button on control module to begin operation.
8. Cleaner will begin operation.
The Cleaner comes ready to run, simply follow the directions below to
begin operation
2
12 cm
(4.7 inch)
4m/12ft
1
2
43
5 6
8
Guide de démarrage rapide
Kurzanleitung
Manuale di avvio rapido
Guía de inicio rápido
Guia de início rápido
Snelstart handleiding
7
START
Quick start guide
Congratulations on purchasing your HY-CLOR Robotic Pool Cleaner
HY-CLOR Robotic Pool Cleaners are manufactured to the highest standards using state of the art technologies
that will provide you with many years of reliable service.
The HY-CLOR Robotic Pool Cleaner is easily installed into new and existing swimming pools in a few
minutes. The silent operation, large debris collection capacity and its ability to clean without affecting your
swimming pools filtration system ensures your pool will look great day in day out.
Before purchasing and installing this product please consult with your swimming pool manufacturer to
determine if this product is suitable for your swimming pool type.
Alternately contact us on our 7 DAY HELP LINE for advice on this product. Our friendly expert pool
professionals will answer all your installation and technical questions.
The HY-CLOR TEAM
7 day help desk
HY-CLOR provides a 7 day technical
information service to Customers
and Bunnings Team Members.
POOL PROBLEMS
ACCESSORY ADVICE
PUMP & FILTER GUIDANCE
POOL CLEANER SELECTION
FRee Call
1800 625 123
HY-CLOR offers a comprehensive product range including chemicals, accessories, pool
cleaners, spare parts, pumps and filters. You’ll find everything you need to make owning a
swimming pool and spa fun and easy.
You are never alone as our Help Line is available 7 days a week to answer your questions.
Whether it’s how to fix a green pool, advice on how to install a pump, which pool cleaner to
choose, or simply how to make your pool water shine. Our friendly highly trained staff will
provide you with the most suitable solutions for all of your pool and spa needs.
CONTENTS
SECTION 1. CHLORINE SANITISERS 2 – 4
SECTION 2. ADJUSTERS 5 – 6
SECTION 3. ALGAECIDES 7 – 8
SECTION 4. CLARIFIERS 9 – 10
SECTION 5. SPECIALITY 11 – 14
SECTION 6. SPA RANGE 15 – 18
SECTION 7. ACCESSORIES 19 – 29
SECTION 8. AUTOMATIC POOL CLEANERS 30 – 32
SECTION 9. PUMPS AND FILTERS 33 – 36
SECTION 10. SALT WATER CHLORINATOR 33 – 37
SECTION 11. FAQ’S & TROUBLE SHOOTING GUIDES 40 – 47
SAFETY DIRECTIONS
The HY-CLOR help line operates Monday to Friday from 8.00am until 8.00pm and on weekends from 8.00am until 4.00pm AEST.
HyClor Roboworks Manual.indd 2-3 25/06/13 10:41 AM
Cleaning the debris bags
1. Turn the cleaner off at the control module and unplug the unit at the 240 volt power supply.
2. Press the two tabs on each side of the cleaner body down and to the side.
3. Lift the cleaner body off the chassis.
4. The debris bags are located inside the body and are attached to the ports with an elastic banded cloth
woven into the debris bag.
5. Remove the debris bags from the cleaner and pull apart the bag tops where they are snapped together.
6. Turn bag inside out to empty collected debris.
7. Hose any excess dirt and grit out of the bags and re assemble.
8. Place bags back into cleaner and attach to the bag ports. Replace the cleaner body back onto the
cleaner chassis.
3
Programming the Robotic Cleaner
The Cleaner comes with two timer modes for simple operation.
1. Mode 1 is for operation in small pools – operates for one hour.
2. Mode 2 is for operation in larger pools – operates for two hours.
4
To set cleaning mode:
1. Small pools press select button and toggle until it selects 1 hour.
2. Large pools press select button and toggle until it selects 2 hours.
Intake Valve Adjustment
Adjusting the intakes allows for larger leaves and debris to be collected by the cleaner.
The factory setting is usually sufficient for standard pool operation.
1. Turn the cleaner upside down.
2. Using a screw driver adjust the tension on the intake valve doors to the desired setting.
3. Adjust water suction intake port.
4. Ensure that you do not tighten the intake door too far as water and debris may not pass into the cleaner
debris bags.
12 cm
(4.7 inch)
4m/12ft
1
2
43
5 6
8
Guide de démarrage rapide
Kurzanleitung
Manuale di avvio rapido
Guía de inicio rápido
Guia de início rápido
Snelstart handleiding
7
STOP
Nettoyage du filtre
Reinigung des Filters
Pulizia del filtro
Limpieza del filtro
Limpeza do filtro
De filter reinigen
START
1 2 3
4
5
6
7
8
9
Quick start guide
Cleaning the filter
Programmes de Nettoyage
Reinigung Programme
Programmi per la pulizia
Programas de limpieza
Programas de limpeza
Reinigingsprogramma
Cleaning programs
Small Pool
Petite Piscine
Kleinen Pool
Piccola Piscina
Pequeña Piscina
Pequena Piscina
Klein Zwembad
1h
Large Pool
Grande Piscine
Großen Pool
Grande Piscina
Gran Piscina
Grande Piscina
Groot Zwembad
2h
Ajutement soupapes d’admission
Einlassventile Einstellung
Adattamento valvole in ingresso
Ajuste válvulas de admisión
Ajuste válvulas de admissão
Inlaatklep aanpassingen
Intake valves
adjustment
1
2
3 4
Programmes de Nettoyage
Reinigung Programme
Programmi per la pulizia
Programas de limpieza
Programas de limpeza
Reinigingsprogramma
Cleaning programs
Small Pool
Petite Piscine
Kleinen Pool
Piccola Piscina
Pequeña Piscina
Pequena Piscina
Klein Zwembad
1h
Large Pool
Grande Piscine
Großen Pool
Grande Piscina
Gran Piscina
Grande Piscina
Groot Zwembad
2h
HyClor Roboworks Manual.indd 4-5 25/06/13 10:41 AM
Loading...