H.Wilson WPS4E, WPS4BRE, WPS4BR5E User Manual

H. Wilson Company

2245 Delany Road
Waukegan, IL 60087
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Visit: www.hwilson.com

REVISED 12/09

NOTE: The 'BR' and 5 in the model number is a color designation.
WPS4E Is the same unit as WPS4BRE and WPS4BR5E. WPS4CE is the
same as WPS4BRCE.

Parts List

(1) Top Shelf (18”W x 16”L)
(1) Adjustable Shelf (18”W x 18”L)
(1) Middle Shelf (15”W x 15”L)
(1) Bottom Shelf (15”W x 30 1/2”L)
(1) Modesty Panel (18"L x 16 1/2"W)
(1) Left Side Frame
(1) Right Side Frame
(4) Plastic Plugs
(4) Stickers
(1) Wrench
(4) Flat Washers
(4) Spring Washers

A. (2) Locking 3” Casters
B. (2) Non-locking 3” Casters
C. (24) 3/4” Panhead Screws
D. (4) 2" Flathead Screws
E. (4) 2” Panhead Screws
F. (2) Support Brackets for Second Shelf
G. (4) Small Brackets for Top Shelf
H. (4) Locking Nuts
Allen Wrench Included

1

WPS4E, WPS4BRE, &

WPS4BR5E

Important Assembly Tip:
When assembling
a WPS4E OR a
WPS4CE, do not
tighten the screws all
the way down. Leave
them approximately 1/2
turn out. When unit is
fully assembled, tighten
screws all the way. This
will allow the unit to line
up correctly.

If you have purchased a unit with a
cabinet please refer to WPS4CE, Cabinet

Instructions on Page 2.

Instructions for Open Shelf (No
Cabinet):

1. Take one of the side frames and lay flat. Attach bot­tom shelf to side frame using (2) 2" flathead screws &
locknuts. Take frame assembly and position it so that
the side panel is resting on the back edge and the shelf
is in a vertical position. Attach the second side frame
panel to the bottom shelf. (Figure 1)

2

3

2. To attach the casters, insert first the spring washer,
then the flat washer over the stem in the caster. Screw
in threaded caster. Do the same for all (4) casters,
making sure that the locking casters are on the same
side. Tighten casters with wrench that is provided. (See

Image #1)

3. Take Modesty Panel (18" x16 1/2") and attach using
(8) 3/4” screws (C). (See Image #4). Attach to side of
panels where the bottom shelf extends further out.

4. Attach middle shelf (15” x 15”) (one flat side/one
rounded side) using (4) 2" screws (E). Put screws
through the guide holes that are on the side panels
making sure that flat side of shelf is flush with the side
where the bottom shelf extends further out. (See Image

#2)

5. Take top shelf (18” x 16”) and attach the (4) small
“L” shaped brackets (G) to the underside of the shelf.
(See Image #3) The brackets have two different style
holes on them (perfectly round and oval). Attach the
round side to the bottom of the shelf using (4) 3/4” (C)
screws, making sure that the other side of the bracket
is facing towards the outside of the shelf. When attach­ing shelf to top of side panels make sure the “L” brack­ets line up with the pre-drilled holes on the side panels.
Attach using (4) 3/4” screws (C).

Page 1 of 3

6. Take adjustable shelf (18” x 18”) and attach the (2) large “L” support
brackets (F) using (4) 3/4” screws (C) making sure that the smooth side of
the bracket is facing the outside of the shelf. Then take adjustable shelf and
attach to the panels at the desired height using (4) 3/4" screws. (If you would
like the adjustable shelf lower, you may take out the top (2) screws of the
Modesty Panel and line up the bottom hole of the brackets with the top hole
of the Modesty Panel and attach using the 3/4” screws). (Image #5)

7. Insert the (4) grommets into the holes on the bottom shelf. Place sticker
over the smaller hole. (Image #6)

Electrical Option: If you received the unit with an electrical assembly you
may attach the electrical assembly vertically on the outside or inside of the
side panels. Attaching with the screws and wing nuts provided with the elec­trical packet.

WPS4CE, WPS4BRCE, & WPS4BR5CE
Presentation Station

5

with Cabinet

Parts List

(1) Top Shelf (18”W x 16”L)
(1) Adjustable Shelf (18”W x 18”L)
(1) Middle Shelf (15”W x 15”L)
(Cabinet Top)
(1) Bottom Shelf (15”W x 30 1/2”L)
(1) Cabinet Left Side Panel
(18 1/4"L x 13 3/4W")
(1) Cabinet Right Side Panel
(18 1/4L" x 13 3/4W")
(1) Door Panel (25"L x 13 1/4"W)
(1) Left Side Frame
(1) Right Side Frame
(1) Modesty Panel
(4) Spring Washers
(4) Flat Washers
(1) Wrench

A. (2) Locking 3” Casters
B. (2) Non-locking 3” Casters
C. (24) 3/4” Panhead Screws
D. (4) 2" Flathead Screws
E. (4) 2” Panhead Screws
F. (2) Support Brackets for Second Shelf
G. (4) Small Brackets for Top Shelf
H. (2) Spindles
I. (1) Magnetic Catch and Strip
J. (6) Chipboard Screws
K. (1) Cam Lock
L. (2) 5/32" Screws for Handle
M. (1) Handle

Instructions:

1. Take one of the side frames and lay flat.
Attach bottom shelf to side frame using (2)
2" flathead screws & locknuts. Take frame
assembly and position it so that the side panel
is resting on the back edge and the shelf is
in a vertical position. Attach the second side
frame panel to the bottom shelf. (Figure 1)

2. To attach the casters, insert first the spring
washer, then the flat washer over the stem in
the caster. Screw in threaded caster. Do the
same for all (4) casters, making sure that the
locking casters are on the same side. Tighten
casters with wrench that is provided. (See

Image #1)

3. Take Middle Shelf (Cabinet Top Shelf 15" x
15") and using (2) chipboard screws (J) insert
the magnetic catch (I) into the pre-drilled holes

in the shelf. (See Image #2 on next page)

Revised 06/08

Page 2 of 3