HWASUNG SYSTEM HP 500 User Manual

Technical Manual

(Model : HP-500)

CAUTION

• Please do not disassemble / reorganize the product.

• Please do not the remove the paper jam during power on.

• Pleased do not exceed the standard power voltage.

• Please do not wash off the product.

• Please do not press / shock the product.

• Please do not put the product at the moist (humid) condition.

• Please contact us if there is any problem.

• Please power off once remove the paper jam.

• Please clear the air / open the disclosed place.

• Please set the product without damage enviornment.

• Please set the product at the stable place.

• Pleaes keep the requires as necessary as general electrics.

Title Rev. Page

HP-500 Ver 1 Ver1.0 P.1

목 차

1. Printer features & External dimension 3
1-1) Name of each parts 3

1-2) Operation Part 4

2. Operation 5

2-1) Replacing the roll of paper 5
2-2) Self test 6
2-3) Communicatino Sett ing up 7

2-4) HEX Dump 8

2-5) Update 9
2-6) Memory switch 10

2-7) Way of connecting WiFi or Bluetoorh 13

(RF Interface)

3. Genearl Specification 13
3-1) Specification 13
3-2) Font 13
3-3) Inner Buffer 13
3-4) Electronical Spec 13
3-5) Operation condition 13
3-6) MCBF 13

4. Interface Specification 14
4-1)RS-232C 14
4-2)USB 14
4-3)WiFi 14
4-4)BlueTooth 14

5. Command 15

6.Windows Driver 40

6-1) Set up the function 40
6-2) Set up the paper 41
6-3) Set up the new paper 42

7. USB User Interface 44

7-1)

functions 44

7-2) Caution for using USB Interface 46

Title Rev. Page

HP-500 Ver 1 Ver1.0 P.2

1. Printer features & External Dimension

1. Button and LED

6. USB/RS232C Interface

1 2 3 4 5 6

1-1) Name of each parts

2. Open Lever

3. Maual Cutter

4. Battery

5. DC Connect

Title Rev. Page

HP-500 Ver 1 Ver1.0 P.3

1-2) Operation Parts

Battery

Power

* Battary State

3 light is “ Full “ charged.
2 light is “ Middle “ Charged
1 light is “ Low “ it needed to be charged.
If the light in Error LED is “ Very Low “ in a battary

* Power

Power on : Please press the button for 1 sec more.
Power off : Please press the button for 1 sec more.

* FEED

Paper feeding .

* Error

If there is something worng, it will be light as Red when there is no paper or out of bettary

* WiFi and Bluetooth

When operating WiFi or BlueTooth, the LED indicator will be lighting.

* Setting the Lable.

You can use the label paper after setting label option.

① Power on the printer
② Open the paper cover and Press the FEED button for 2 seconds.
③ When Melody is alaming, Put the paper of label in the printer and close the paper cover.

When it comes back to Receipt Option, Please follow this step again.

WiFi

BlueTooth

FEED

Error

Title Rev. Page

HP-500 Ver 1 Ver1.0 P.4

2. Operation

Lever

②

Open the cover in Mobile Printer by Lever

③

2-1) Replacing the roll of paper.

The paper setting up is as below.

①

Please insert the paper, till the paper comes out from

the cover.

Close the cover and cut the extra paper.

Title Rev. Page

HP-500 Ver 1 Ver1.0 P.5

2-2 ) Selftest

Please turn off and on the power, while you press down the feed button.

And you can see the Error Led light kept then the following informations are being feeded.

******************************

HP-500 Control Board

Firmware :: Ver0 .45

Create : 20XX/XX/XX

******************************

 Model.
 Firmware version / creare date.
 Printer information.
 Serial I/F information
 WiFi information

Printer Information

Battery Volt : 7.7(V)

Hex Dump Mode : OFF

Print Density : Normal

Melody Sound : ON

Paper Type : Receipt

Wireless Type : WiFi / BlueTooth

Power off time : 10 Minute

Tear Bar : 5 Pitch

Serial I/F Information

Baud Rate : 9600

Date Bit : 8 bit

Partiy : None

Stop Bit : 1 or 2

Flow Control : RTS-CTS(DTR-DSR)

WiFi Information

WiFi Mode : AP Mode

IP Address : 192.168.012.101

Gateway : 192.168.012.001

SSID : HWASUNG_4E:8E:EE

SECURITY KEY : 12345678

Title Rev. Page

HP-500 Ver 1 Ver1.0 P.6

2-3 ) Communication setting

Set the printer function and communication condition between host by memory switch utility

program.

※ Note : Setting ereases all contents in memory switch, so code page and print optionshall be set

again.

1 ) Manual setting

Turn on the printer at initial setting mode.

※ Method to go initial setting mode

[ Press and hold FEED button and then turn on power pressing 2 or more seconds, then PE LED and

ERROR LED blinks by turns and it is switched to initial setting mode (9600 BPS, PARITY NONE,
HARDWARE HANDSHAKE).]
In manual setting, considering of communication condition is not required.

2 ) After switched to initial setting mode, followings will be printed.

.

[Menu]

1.Print Density

2.Melody Sound

3.Paper Type

4.Hex Dump Mode

5.Wireless Type

6.WiFi Mode

7.IP Mode
Select and then Enter...

Enter : Press the feed button once for
more than 1second.
Select: Press the feed button many times
less than 1second as menu number.
Exit : Turn power off then on.

Pressing FEED button for more than 1second, it is fixed(press enter), and less than 1 second, item

is selected.

For example, if you want to change the Wifi Mode of #6 menu, press #6 less than 1 second, and

press more than 1 second. To exit, turn off the power and turn on again.

3) Successively, select from printed items and confirm.

Ex) [Wireless Type]

1.WiFi

-> 2.Bluetooth

-> : Indicate current set status

Select and then Enter...

Ex) In here, arrow((->) indicates current settings. To change, select item and enter. TO move to

Title Rev. Page

HP-500 Ver 1 Ver1.0 P.7

next menu with no change, just enter without selecting item.

4) Successively, you will know the change result from the printed items.
“ It was changed successfully!”
This message means change was successful.

“ The value is invalid, try again!”

This message is shown when selected item is invalid or when you move to other menu without item
change.

5) Setting result can be confirmed by printing test page or by the location of arrow(->) after selecting
menu item in initial setting mode.

2-4) HEX Dump

Setting up “Hex Dump Mode in Setting Mode. Then it prints all data in hex character

(16 antilogarithm).

You can see the status of receipt. . It will be useful for the appilcation you do.

 It prints the data, once it receives the data 12 digit.
 You can print the data less than 12 digit, when you press down the button of feed
 The control code ( 1F
 The 80

16 above prints “^”.

16 below) prints “.”.

[Printing sample]

16 antilogarithm ASCII

[HEX DUMP MODE]
41 42 43 44 45 46 47 47 49 A B C D E F G H I
30 31 32 33 34 35 36 37 38 0 1 2 3 4 5 6 7 8
FF 1B 69 ^ . i

Title Rev. Page

HP-500 Ver 1 Ver1.0 P.8

2-5) Onboard update

Please conduct the updates, after refering the following steps.

1) Please switch off and on

2) Please check the connection between the printer and the data cable.

* Please make sure about if it is the right cable.

* If use USB cable, save the time to update the firmware

3) Please conduct the provided program , then set up the model and Interface port

If the error LED is turned off and is lighted on slightly after 4 seconds,
then the updated is being started.

* Please do not switch off the printer power, till the update is complete.

4) The update will be complete, once the update indicates complete.

* If the error LED keeps the light goes in and out, it’s error.
Please stop the update program and make sure the cable and other connections.
Please return the process “1.” and follow the step again.

5) At fer update, automatically the printer will be reset for using and use the printer.

Title Rev. Page

HP-500 Ver 1 Ver1.0 P.9

2-6) Memory switch

Memory SW

Setting Value

Descreption

SW1

Reservation

SW2

0~1200 or 0~136

SW3

248-4000

SW4

Base Code Page

Setting one

SW5

Base Font

Setting one of

SW6

Reservation

SW7

Reservation

SW8

Reservation

Code Page Manu

Font Manu

After setting, Press the button

Setting
paper

Please set the function of internal memory.

※ Please use the provided program - ‘memory swtich setting utility program’.
※ The value is not deleted until the next value is changed, even though power off.

default value for each country

1) 2byte codes : korean(24 x 24), korean(16 x 16),
Japenes(24x24), Chinese(24x24).

2).1byte codes : ASCII(12x24),
ASCII(8x16,9x16)

Title Rev. Page

HP-500 Ver 1 Ver1.0 P.10

[Memory Switch information]

(Ex) Sample of printing by selftest

================================
Code Page = PC437(U.S)
2Byte Font = Korean(24x24)
1Byte Font = ASCII(12x24)
Mem1:FFh
Mem2:FFh,FFh
Mem3:FFh,FFh
Mem4:00h
Mem5:00h
Mem6:FFh
Mem7:FFh
Mem8:FFh
Mem9:FFh
Mem10:FFh
Mem11:40h
Mem12:F9h

Title Rev. Page

HP-500 Ver 1 Ver1.0 P.11

2-7) The way to connect the RF interface.

1) BlueTooth

BlueTooth inteferface can be set up by simple control

① Please refer to 2-3P and set up from Wireless moder to Bluetooth

② When the Error LED is not lighting, Pressing power button and FEED button togather for

1second then take off.

③ And searching for Bluetooth device in Mobile Phon e or PC

④ When finding “HWASUNG_XX:XX:XX” on PC or Smart Phone and choosing it and it will be

pairing automatically.

⑤ the pairing is complete ordinarily, the light in LED bluetooth will be stopped.

2) WiFi

There are two of modes

Station Mode : Printer will be connected with Wireless directely.(SSID and others Setting

necessary)

AP Mode : Printer will be connected with other de vices (Not setting necessary)

① Please refer to 2-3 and Set up “ Wireless Mode “
② Please refer to 2-3 and Set up “ Station Mode “ or “ AP Mode “ according to where you use.

When choose the mode is “AP Mode “

③ Turn on the printer and atfer 3 sec ond aut omat ically IP Address and SSID an d Passwor d will be

printed.

④ And please connect wit h PC or Smart Phone then put in the SSID and Password.
⑤ When the connection is complete, using IP address printed.

Title Rev. Page

HP-500 Ver 1 Ver1.0 P.12

3. General Specification

Insert Voltage

7.4V Li-ion Battery

Operation voltage

5V

Motor,Thermal print head

Logic voltage

5V±5%

Logic circuit

3-1) Specification

1) Printing : Direct thermal printer

2) Resolution and Dot : 203dpi, 1dot=0.125mm, 8dot/mm, Total 384 dot

3) Printing speed (Max) : 90mm/sec(Max)

4) Printing Width : 48mm

5) Paper Width : 58mm

6) Paper Diameter : 40 Diameter (Max)

7) Character (MAX) a line : 32fonts (ASCII 12 x 24),16fonts (Korean 24 x 24)

3-2) Font

1) English / Number FONT A(8 x 24) 95, FONT B(8 x 16) 95

2) Graphic FONT A(8 x 24) 128, FONT B(8 x 20) 95

3) International 14types 37fonts
(Korean,English,France,Germany,England,Denmark1,Swden,Italy,
Spain1,Japan,Norway,Denmark2,Spain2,Latin America)

4) Korean FONT A Gothic (24 x 24), FONT B Gothic (16 x 16,option)

3-3) Internal Buffer

Receiver buffer : 4KByte

3-4) Electrical Spec

1) Operating Voltage

2) Consumption current
Average : 1.5A(Printing percentage 12.5%))
Peak : 3.7A

3-5) Operation condition (temperature / Humid)

1) Temperature : 0∼40℃

2) Humidity : 40∼90%RH(in not dew condensation)

Notice : The printing is subjet to the operation condition.

3-6) MCBF

1) Mechanism : 15,000,000 Lines.

2) Thermal Print Head 50Km, 1 pulse.

Title Rev. Page

HP-500 Ver 1 Ver1.0 P.13