Huvitz CCP-3100 User manual

-------------------------------------------------------------------- CCP-3100 Opreator’s Manual 1

Operator’s Manual

Chart Projector

2

CCP-3100 Operator’s Manual -----------------------------------------------------------------------

IMPORTANT NOTICE

This product may malfunction due to electromagnetic waves caused by portable

personal telephones, transceivers, radio-controlled toys, etc. Be sure to avoid having

objects such as, which affect this product, brought near the product.

The information in this publication has been carefully checked and is believed to be

entirely accurate at the time of publication. HUVITZ assumes no responsibility,

however, for possible errors or omissions, or for any consequences resulting from

the use of the information contained herein.

HUVITZ reserves the right to make changes in its products or product specifications

at any time and without prior notice, and is not required to update this documentation

to reflect such changes.

©2002 - 2004 HUVITZ Co., Ltd.

689-3, Geumjeong-dong, Gunpo-si, Gyeonggi-do,

435-862, Republic of Korea

-------------------------------------------------------------------- CCP-3100 Opreator’s Manual 3

All rights are reserved.

Under copyright laws, this manual may not be copied, in whole or in part, without

the prior written consent of HUVITZ Co., Ltd.

Document Number: 9000OMCP001-A, published in 2006/07/20

CONTENTS

1. Introduction .............................................................................................................5

1.1. Outline of product ..............................................................................................5

1.2. Classifications ...................................................................................................5

1.3 Certification …………………………………………………………………………..5

2. Safety Information...................................................................................................6

2.1. Introduction........................................................................................................6

2.2. Safety Symbols..................................................................................................7

2.3. Environmental factors........................................................................................8

2.4. Safety Precautions ............................................................................................9

3. Features…..............................................................................................................11

4. Notes for Using the Instrument ............................................................................ 12

5. Configurations.......................................................................................................13

5.1. Main Body .......................................................................................................13

5.2. Main Body cont................................................................................................14

5.3. Accessories.....................................................................................................15

6. Installation.. ...........................................................................................................16

6.1. Position of Chart Projector...............................................................................16

6.2. How to obtain correct Letter Size and focus (Zooming Type only).................... 17

4

CCP-3100 Operator’s Manual -----------------------------------------------------------------------

7. Input and Use of Program.....................................................................................18

7.1. How to input user's program ............................................................................18

7.2. How to use your stored programs....................................................................19

8. Types of Chart (Type C is Standard)..................................................................20

9. Maintenance and Repair........................................................................................21

9.1. Lamp Replacement..........................................................................................21

9.2. Fuse Replacement...........................................................................................22

9.3 The battery of Remote Controller Replacement …....……………………….23

9.4 Cleaning………………………………………………………………………………24

9.5 Disposal ……………………………………………………………………………..24

10. Specifications ........................................................................................................25

11. Components List ...................................................................................................26

11.1. Standard accessories ......................................................................................26

11.2. Optional accessories .......................................................................................26

12. Service Information ...............................................................................................27

-------------------------------------------------------------------- CCP-3100 Opreator’s Manual 5

1. Introduction

1.1. Outline of product

HUVITZ CCP-3100 is an automatic chart projector which provides 41 different charts

including red/green and polarized filters for the eye optometry. Users can select the

desired charts instantaneously by cordless remote controller. Charts move quickly and

quietly. The customized two programs will help you to perform more convenient and

effective examination. You can also execute the binocular balance tests, stereo tests,

fixation disparity tests, fusion tests and aniseikonia tests with CCP-3100. This

automatic chart project is compatible with HUVITZ digital refractor, CDR-3100.

Equipment intended for connection to signal input and signal output, shall with

IEC60601-1, or UL60601-1 harmonized national standard or the combination.

If, in doubt, contact qualified technician for helf.

1.2. Classifications

 Class I equipment (CCP-3100)

 No applied part

 Ordinary equipment (IPX 0)

 Equipment not suitable for use in the presence of a flammable anesthetic mixture

with air or with oxygen or nitrous oxide

 Continuous operation equipment

1.3. Certification

6

!!!!

WARNING

!!!!

CAUTION

CCP-3100 Operator’s Manual -----------------------------------------------------------------------

2.Safety Information

2.1 Introduction

Safety is everyone’s responsibility. The safe use of this equipment is largely

dependent upon the installer, user, operator, and maintainer. It is imperative that

personnel study and become familiar with this entire manual before attempting to

install, use, clean, service or adjust this equipment and any associated accessories. It

is paramount that the instructions contained in this manual are fully understood and

followed to enhance safety to the patient and the user/operator. It is for this reason

that the following safety notices have been placed appropriately within the text of this

manual to highlight safety related information or information requiring special

emphasis. All users, operators, and maintainers must be familiar with and pay

particular attention to all Warnings and Cautions incorporated herein.

“Warning ” indicates the presence of a hazard that could result in severe personal injury,

death or substantial property damage if ignored.

NOTE

“Note” describes information for the installation, operation, or maintenance of which is
important but hazard related if ignored.

“Caution” indicates the presence of a hazard that could result in minor injury, or
property damaged if ignored.

-------------------------------------------------------------------- CCP-3100 Opreator’s Manual 7

2.2 Safety Symbols

The International Electrotechnical Commission (IEC) has established a set of symbols

for medical electronic equipment, which classify a connection or warn of any potential

hazards. The classifications and symbols are shown below.

Save these instructions

I and O on the power switch represent ON and OFF

respectively.

This symbol identifies a safety note. Ensure you

understand the function of this control before using it.

Control function is described in the appropriate User’s

or Service Manual.

Hot surface.

Identifies the point where the system safety ground is

fastened to the chassis. Protective earth connected to

conductive parts of Class I equipment for safety

purposes.

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached

to a product it means the product is covered by the

European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed

of separately from the municipal waste stream via designated

collection facilities appointed by the government or the local

authorities.

3. The correct disposal of your old appliance will help

prevent potential negative consequences for the environment

and human health.

4. For more detailed information about disposal of your old

appliance, please contact your city office, waste disposal

service or the shop where you purchased the product.

8

CCP-3100 Operator’s Manual -----------------------------------------------------------------------

2.3 Environmental factors

Avoid the following environments for operation or storage:

Where the equipment is exposed to water vapor.

Don’t operate an equipment with a wet hand.

Where the equipment is exposed to di rect

sunlight.

Where the temperature changes extremely.

Normal operating temperature range is from 10

to 40, Humidity is from 30% to 75%.

Where it is near the heat equipment.

Where the humidity is extremely high or there is a ventilation

problem.

Where the equipment is subject to excessive shocks or

vibrations.

Where equipment is exposed to chemical material or

explosive gas.

Be careful not to be inserted dust, especially, metal

-------------------------------------------------------------------- CCP-3100 Opreator’s Manual 9

Avoid places where the ambient temperature falls below 10℃ or exceeds 40℃ for

normal operation, or below -10℃ or exceeds 40℃ (14℉-104℉) for transportation

and storage. Humidity should be maintained between 30 and 75% for normal

operation, transportation and storage and atmospheric pressure (700~1060hpa).

Avoid environments where the equipment is exposed to excessive shocks or

vibrations.

2.4 Safety Precautions

This equipment has been developed and tested according to national as well as

international safety standards. This guarantees a very high degree of safety for this

device. The correct handling of this equipment is imperative for its safe operation.

Therefore, please read carefully all instructions before switching on this device. For

more detailed information, please contact our Customer Service Department or one of

our authorized representatives.

1. This equipment must not be used (a) in an area that is in danger of

explosions and (b) in the presence of flammable, explosive, or volatile

solvents such as alcohol, benzene or similar chemicals.

2. Do not put or use this device in humid rooms. Humidity should be

maintained between 30 and 75% for normal operation. Do not expose the

device to water splashes, dripping water, or sprayed water. Do not place

containers containing fluids, liquids, or gases on top of any electrical

equipment or devices.

3. The equipment must be operated only by, or under direct supervision of

a properly trained and qualified person.

4. Customer maintenance of this equipment may only be performed as

stated in the User’s Manual. Any additional maintenance may only be

performed by HUVITZ service technicians or other authorized persons.