HuTools KS01 Installation Manual
PLEASE KEEP THIS GUIDE
This guide contains important information about your lock.
HuTools KS01
Installation Guide
Installation Guide
Backup Key
Exterior
Assembly
Latch
Latch/Strike
Screws(I)
Mounting
Plate
Reinforcement
Screws(H)
Interior
Assembly
Mounting Plate
Screws(J)
Strike
Battery
Cover
Interior Assembly
Screws(K)
Parts List
Latch
A
Mounting Plate
Mounting Plate
Screws
J
Drive-In Collar
Interior
Assembly
E
Interior Assembly
Screws
Strike
B
Battery Cover
C
G
F
Backup Key
K
L
Exterior Assembly
D
Latch and
Strike Screws
I
H
Prepare the door and check dimensions
1
Measure to confirm that the hole in the door
A B C D
is 2-1/8" (54 mm)
2-1/8"
54 mm
Install the latch and strike
2
Measure to confirm that the backset is
either 2-3/8" or 2-3/4" (60 or 70 mm)
2-3/8" or 2-3/4"
60 or 70 mm
backset
Measure to confirm that the the hole in
the door edge is 1" (25 mm)
1"
25 mm
Measure to confirm that the door is 1-3/8"
to 2" (35 mm or 50 mm)thick
1-3/8" to 2"
35 mm to 50 mm
Hold the latch in front of the door hole, with
A B C
the latch face flush against the door edge.
A
Is the slotted hole centered in the door hole?
YES
NO
or
Slotted hole is centered. Slotted hole is NOT centered.
No adjustment is
required. Proceed
to next step.
Rotate and pull the
latch as shown
to extend latch.
1
Is the door edge chiseled?
YES
chiseled
Install latch in door with
supplied screws.
NO
or
Use a flathead screwdriver to remove
Rectangular face from latch and install
I
drive-in collar.
1
2
3
B
4
not
chiseled
D
Use a screwdirver to test if deadbolt works smoothy.
Install strike on the door frame.
IMPORTANT: Make sure hole in door frame is
drilled a minimum of 1" (25 mm) deep.
H
C
2
φ2-3/4”
(70mm)
Install latch in door with wood
block and hammer.
1 / 6
Install exterior assembly
3
IMPORTANT: Before installation, make sure the latch is fully retracted (in the unlocked position) . Route the cable below the latch.
A
unlocked
B
Insert the torque blade
through the slot in the latch.
Send the cable through the bottom horizontal slot in the mounting plate.
C
Install interior assembly
4
A
IMPORTANT: Do not load batteries until lock is completely installed.
Remove the battery cover.
Locate the slot at the bottom and use your fingernail or a
flat head screwdriver to pry the cover up and pull it off.
Secure the mounting plate with the supplied screws.
D
Keep Parallel to door edge.
unlocked
Connect the cable and ensure tight cable connection.
B
E
J
Rotate the turnpiece in vertical position and make sure
C
the latch is still fully retracted (in the unlocked position).
Insert the torque blade through the center hole in the
mounting plate.
F
G
Test the turnpiece for smooth rotation.
D
If turnpiece doesn’t rotate, repeat step 4C,
making sure the turnpiece in vertical position.
Secure the interior assembly
E
with the supplied screws.
Tourque Blade
K
Detect left/ right hand door installation
5
Reset the lock to teach the lock the orientation of the door.
IMPORTANT: This step is required and crucial for the lock to operate properly.
While the door is OPEN and UNLOCK, load 3 AA batteries
A
into the interior assembly.
IMPORTANT: For best results, use new, non-rechargeable
Alkaline batteries only.
unlocked
Press and hold the Reset button on the interior assembly
B
using a pen or a paper clip.
2 / 6
Load the last battery and keep holding the reset button for
C
10 seconds, until you hear the sound of “beep”. The latch
bolt will extend to learn the orientation of the door.
Loading...