PARTS LIST
Item Quantity Description
RL/RM RLN RLNI
RM/RMF RMN RLNIE RLT
1.2242Donut Gasket
2.1122Gasket, 1 x
1
/2
x 180 in.
3.1121Gasket,
1
/2 x 1/4 x 180 in.
4. 6 6 12 6 Cap Screw
5
/16 -18 x 11/4
5. 6 6 12 6 Split Lock Washers
5
/16
6.1121Joint Molding
7. 5 5 10 5 Binder Post and Screw
8.1121Splice Connector
Merchandisers
®
RL / RM / RMF, RLT
RLN / RMN / RLNI / RLNIE
Joining Instructions
Reach-in Merchandisers
NOTE: Be sure first merchandiser
has been leveled according to the
main installation instruction.
Carefully unpack and inspect the
joining parts listed above to verify
completeness and that there is no
damage.
1
Prepare cases for joining (both
sides of islands) as shown in
Figure 1.
A. Remove bumpers, rails,
packing materials, and splashguards from the both cases.
B. Remove shelves (if
installed).
C. Remove display racks and
pans from ends to be joined.
D. Remove rear shelf supports.
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
1
Splashguard brackets must
be installed before piping
or wiring case.
C
Figure 1. Prepare Cases
Bumper
Bumper
Retainer
Splashguard
SIDE VIEW
Raceway
A
A
RLT
P/N 0387177F
October 2005
B
E
SIDE VIEW
Bumper
Retainer
Splashguard
C
A
Bumper
D
E. Remove back panels from
ends to be joined by lifting up
and out near the bottom. No
tools are necessary. The RLT
models have upper and lower
back panels that must be
removed.
F. Remove joint molding from
any door frames that will be
joined to another case.
G. RLNI Only: Remove screws
and interior top panel on both
sides of the island case end to
be joined (see Figure 1).
P/N 0387177F
2
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
G
G
RLNI Only
Alignment Pin
F
RL / RM / RMF
RLN / RMN
and RLNI
RLT
®
Merchandisers
E
E
2
Locate and remove the shipping
block in the center of the heat
exchanger in the interior bottom
of each case, see Figure 2.
Snap a chalk line on the floor to
use as a guide for positioning
the front of the cases in the lineup. The front base frame should
be on the chalk line.
3
Once cases are close to final
placement, remove the shipping
braces from the ends to be
joined, see Figure 3. Discard
bolts and flat washers used to
hold shipping braces. Bolts
are too long to be used for
joining.
P/N 0387177F
Reach-in Joining Instruction
3
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Figure 2. Remove Shipping Block
(One From Each Side of Island Models)
Shipping
Block
RMN
RLNI / RLNI
Figure 3. Remove Shipping Braces
D
O NOT USE SHIPPING BOLTS TO JOIN CASES
!
Shipping Brace
P/N 0387177F
4
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
RL / RM / RMF
and
RLN / RMN
4
If not already installed make
sure Nut Retainers and
Alignment Pins are in place in
the right end frame as shown in
Figure 4A or 4B.
RLT
Figure 4A. Verify Nut Retainer Installation
®
Merchandisers
Factory Installed
Nut Retainer
RLT has no
Alignment Pin
Factory Installed
Nut Retainer
P/N 0387177F
Reach-in Joining Instruction
5
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
RLNI
Figure 4B. Verify Nut Retainer Installation
Alignment Pin
Alignment Pin
Loading...