How it Works
Hussmann
Loading...
HEDN02

Hussmann HEDN, HEDW, HEDN02, HEDW05, HEDN03 Installation And Operation Manual

...
Manual
REV. 0508
/CHINO
HEDN (02,03,04,05), HED COMBO, HEDW05
HEDN HOT END DISPLAY
HEDN (02,03,04,05) HED COMBO HEDW05
HED HOT CASE FAMILY
P/N IGHT-HEDN, HEDN COMBO, HEDW-0508
INSTALLATION & OPERATION GUIDE
General Instructions
This equipment is to be installed to comply with the applicable NEC, Federal, State , and Local Plumbing and Construction Code h a ving j urisdict i o n .
Table of Contents
General Instructions.....................................................2
Cut and Plan Views ......................................................3
Installation .....................................................................4
Leveling/Joining Instructions...................................................... 4
Electrical........................................................................4
Wiring Color Code ..................................................................... 4
Electrical Circuit Identication .................................................... 4
Electrical Service Receptacles .................................................. 4
Field Wiring and Serial Plate Amperage .................................... 4
Ballast Location .........................................................................4
Operation .......................................................................5
Controls .....................................................................................5
Daily Startup .............................................................................. 5
Operation Tips ........................................................................... 5
Shut-down and Cleaning ........................................................... 5
Electrical Wiring Diagrams ..........................................7
Wiring Diagrams ...........................................................8
Appendices ................................................................. 69
Appendix A - Temperature Guidelines - Refrigerated .............. 69
Appendix B - Application Recommendations - Refrigerated .... 69
Appendix C - Field Recommendations - Refrigerated ............. 70
Appendix D - Recommendations to User - Refrigerated ......... 71
IGHT-HEDN, HEDN COMBO, HEDW-0508
This Booklet Contains Information on:
HED HOT CASES
Self Service Hot cases designed to t within a lineup of
multidec self service cases or at the end of a lineup.
Shipping Damage
All equipment should be thoroughly examined for shipping damage before and during unloading.
This equipment has been carefully inspected at our factory and the carrier has assumed responsibility for safe arrival. If damaged, either apparent or concealed, claim must be made to the carrier.
Apparent Loss or Damage
If there is an obvious loss or damage, it must be noted on the freight bill or express receipt and signed by the carrier’s agent; otherwise, carrier may refuse claim. The carrier will supply necessary claim forms.
Concealed Loss or Damage
When loss or damage is not apparent until after equipment is uncrated, a claim for concealed damage is made. Make
request in writing to carrier for inspection within 15 days, and retain all packaging. The carrier will supply inspection report and required claim forms.
Shortages
Check your shipment for any possible shortages of material. If a shortage should exist and is found to be the responsibility of Hussmann Chino, notify Hussmann Chino. If such a shortage involves the carrier, notify the carrier immediately, and request an inspection. Hussmann Chino will acknowledge shortages within ten days from receipt of equipment.
Hussmann Chino Product Control
The serial number and shipping date of all equipment
has been recorded in Hussmann’s les for warranty and
replacement part purposes. All correspondence pertaining to warranty or parts ordering must include the serial number of each piece of equipment involved, in order to provide the customer with the correct parts.
Keep this booklet with the case at all times for future reference.
/CHINO
A publication of HUSSMANN® Chino 13770 Ramona Avenue • Chino, California 91710 (909) 628-8942 FAX (909) 590-4910 (800) 395-9229
2
Rev. 0508
3"
HEDN-03
Scale 1/2"
53"
9
1
/
2
"
247/8"
25"
11
1
/
2
"
203/8"
Optional
rear doors
HEDN-02
Scale 1/2"
247/8"
45"
25"
9
1
/
2
"
211/4"
Optional
rear doors
9
1
/
2
"
11
1
/
2
"
203/8"
13
1
/
2
"
22"
58"
247/8"
HEDN-04
Scale 1/2"
Optional
rear doors
HEDN-05
Scale = 1/2"
3"
14
1
/
2
"
8"8"8"11
3
/
4
"
58"
9
1
/
2
"
11
1
/
2
"
13
1
/
2
"
203/8"
9"
14"
247/8"
21
3
/4"
5"
2
7
/
4
"
5
3
/8"
14"
Shown
with
optional
rear doors
48"
(VARIABLE LENGTHS)
24
7
/
8
"
12
7
/
8
"
36"
21
3
/
4
"
3
3
/
4
"
HEDN
Plan View
Scale = 1/2"
MECHANICAL CONNECTION AREA
12 7/8" X 21 3/4"
Front of Case
8"
1
0
"
HEDN-05 COMBO
Hot Over Cold Self Service
Scale = 1/2"
247/8"
213/4"
8"
58"
9"
3"5"
9
1
/
2
"
12
1
/
4
"
171/8"
8
1
/
4
"8
1
/
8
"
5
5
/
8
"
3
1
/
4
"
14"
Hot
Section
Cold
Section
Optional
Rear
Doors
58"
1
8
1
/
2
"
1
9
1
/
2
"
20
1
/
2
"
20
1
/
2
"
271/2"
HEDW-05
Hot Self Service End Display
Scale = 1/2"
323/4"
7
1
/
2
"
14"
9"5"
3"
HEDW
Plan View
Scale = 1/4"
19"
22
1
/
4
"
Elec. Stub-
Up
Area
19"x12"
11
1
/
2
"
33
3
/
4
"
48"
(VARIABLE LENGTHS)
18"
2"
12"
Cut and Plan Views
3
Installation
TO AVOID REMOVING CONCRETE FLOORING, BEGIN
LINEUP LEVELING FROM THE HIGHEST POINT OF
THE STORE FLOOR.
BEFORE SERVICING
ALWAYS DISCONNECT ELECTRICAL
POWER AT THE MAIN DISCONNECT
WHEN SERVICING OR REPLACING ANY
ELECTRICAL COMPONENT.
This includes (but not limited to) Heaters and Lights.
IMPORTANT! IT IS IMPERATIVE THAT CASES BE LEVELED FROM FRONT TO BACK AND SIDE TO SIDE PRIOR TO JOINING. A LEVEL CASE IS NECESSARY TO INSURE PROPER OPERATION, WATER DRAINAGE, GLASS ALIGNMENT, AND OPERATION OF THE HINGES SUPPORTING THE GLASS. LEVELING THE CASE CORRECTLY WILL SOLVE MOST HINGE OPERATION PROBLEMS.
ALL CASES WERE LEVELED AND JOINED PRIOR TO SHIPMENT, TO INSURE THE CLOSEST POSSIBLE FIT WHEN CASES ARE JOINED IN THE FIELD.
Electrical
Wiring Color Code
CASE MUST BE GROUNDED
IGHT-HEDN, HEDN COMBO, HEDW-0508
Leveling/Joining Instructions
Check oor where cases are to be set to see if it’s level. Determine where the highest part of the oor is. Cases will
be shimmed off this point. Using case blueprints, measure
off and mark on oor the exact dimensions of the case
footprint. Snap chalk line for front and back position of base rail. Mark location of each joint front and back. Use
a transit to nd the highest point along both lines. Mark
the difference, and place the appropriate number of shims required to maintain high - point level.
Electrical Circuit Identication
Standard lighting for all models will be full length uorescent
lamps located within the case at the top. The switch controlling the lights, the plug provided for digital scale, and the thermometer are located at the rear of the case mullion.
The receptacle that is provided on the exterior back of these
models is intended for computerized scales with a ve amp
maximum load, not for large motors or other high wattage appliances. It should be wired to a dedicated circuit.
Electrical Service Receptacles (When Applicable)
The receptacles located on the exterior of the merchandiser are intended for scales and lighted displays. They are not intended nor suitable for large motors or other external appliances.
Field Wiring and Serial Plate Amperage
Field Wiring must be sized for component amperes printed on the serial plate. Actual ampere draw may be less than
specied. Most component amperes are listed in the “Wiring
Diagram” section, but always check the serial plate.
Ballast Location
Ballasts are located within the access panel that runs the length of the rear of the case. Refer to diagram.
4
Rev. 0508
The case metal and the light bulbs become
extremely hot when in use.
DO NOT Touch Hot Case or Lights With bare hands!
DO NOT FLOOD!
Use only enough solution necessary to clean
surface. Water must not drip down the case!
Never use ammonia based cleansers, abrasive
cleansers, or scouring pads.
Operation
Controls
Pictured on the following page is an HED-02 with the appropriate controls. All the HED’s have the same controls, however, as the number of shelves and case lengths vary, the number of these controls does also. Each is clearly labeled on the control panel on the back of the case.
Daily Startup
1. Check to make sure All switches are starting in the "OFF" position
2. Flip O/H Light switches to "ON" position. When
toggle switch is ipped to "on" position, the light to
the left of the on off toggle switches will go on. If it does not, turn the toggle switch to the off position and tell your maintenance department the case is not getting power.
3. Turn shelf light dial (on left hand side) to "5". Light next to dial will cycle on when the unit is heating, and cycle off when it has reached temperature.
4. Turn shelf warmer dial (on right hand side) to "7". The light next to the dial will cycle on when the unit is heating, and cycle off when it has reached temperature.
Operation Tips
1. Check the food to make sure the temperature is correct. Hot foods should be held at a minimum of 140°F.
2. When restocking case, rotate older product to front of case, load newer product in the back.
3. Clean spills as soon as they occur to avoid baked on food soil.
Shut-down and Cleaning
1. Unload product from case.
2. Turn the dials for the Overhead Lights and the Griddle Heat control to the "OFF" position.
3. Allow the case to cool for at least 30-45 minutes before cleaning.
4. Clean the decks of the case with a mild soapy solution and a sponge.
5. Wait an hour before loading pre - heated product*. *These cases are not designed to cook or heat - up food. Food must be at 150°-160°F BEFORE loading into the case. Check food temperature with a thermometer before putting in case.
6. After one hour, measure the product temperature by using a food thermometer.
7. Adjust if necessary, increase or decrease (whichever is appropriate) both dials, one number at a time until the desired temperature has been reached. Measure the product temperature with a thermometer an hour after re - setting the case temperature.
5. Wipe soap residue off with a sponge and clear, clean water. Using caution not to put too much water on the shelf.
6. Dry with clean towel or paper towel.
7. Polish and clean glass with a good glass cleaner.
5
HED-02
Two Level Display
1. Measure PRODUCT temperature hourly by inserting a food thermometer into the food. Proper holding temperature is 140°.
2. To change temperature, increase or decrease Overhead Heat by one number at a time. Adjust the griddle temperature as necessary. Measure product temperature again in one hour. Readjust if necessary.
ADJUST TEMPERATURE
SHUTDOWN
Operation Tips
1. Check the food temperature frequently with a thermometer
to make sure it is proper holding temperature. Hot foods should be held at 140°.
2. Do not display more food than will be sold within a 4 hour
period.
3. When restocking, bring older food to front, stock fresher
food in back.
4. Clean spills as soon as they happen.
5. Oils and splatter will drastically shorten bulb life.
DANGER OF ELECTRICAL SHOCK OR CASE DAMAGE
USE THE MINIMUM AMOUNT OF LIQUID WHEN CLEANING!
Parts of the case exterior, shelves and light
bulbs become extremely hot when in use.
DO NOT
Touch Hot Case or Lights with
bare hands!
Nightly Cleaning
1. Turn case off and unload product.
2. Allow the case to cool for at least 30-45 minutes.
3. Clean the shelves and deck with a mild cleaning solution and sponge. Never use ammonia based cleansers, abrasive cleansers, or scouring pads.
WRING OUT CLOTH /
SPONGE THOROUGHLY BEFORE CLEANING!
4. Wipe residue off with a sponge and clear, clean water.
5. Dry with clean cotton or paper towel.
6. Polish and clean glass with a good glass cleaner
Control Panel
on Rear of Case
1. Turn all switches and dials to "OFF" position.
2. Allow case to cool and clean.
O/H HEAT
LIGHT
LO HI
6
5
4
3
2
ON / OFF
OFF
ON / OFF
OVERHEADHEAT
INITIAL
SETTING
"5"
OVERHEAD LIGHTS ON / OFF
TURN
SWITCHES
ON
GRIDDLE TEMPERA
TURE
INITIAL
SETTING
"7"
Check to make sure all lights come on at start-up.
If they do not contact your Service Department
Allow case preheat for 45 minutes prior to loading
NOTE: This equipment is not designed to heat-up or cook food. Food must be 150° - 160° when put in display.
CONTROL PANEL
GRIDDLE
OVERHEAD HEAT & LAMPS
Parts of the case exterior, shelves and light
bulbs become extremely hot when in use.
USE EXTREME CAUTION!
START-UP
©
HUSSMANN Corp. Chino, California HED Oper Lable/Est r00/05 dmd
430-01-0365 9810
1
2
3
4
5
6
7
8
9
10
S
t
a
r
t
u
p
Operation (Cont'd)
IGHT-HEDN, HEDN COMBO, HEDW-0508
6
Rev. 0508
Electrical Wiring Diagrams
HEDN-02
HEDN-03
HEDN-04
HEDN-05
Hot/Cold Combo
WITHOUT TOP SHELF
HEDW-02
HEDW-03
HEDW-04
HEDW-05
3' W6300092
4' W6300093
5' W6300094
6' W6300095
8' W6300096
3' W6300086
4' W6300097
5' W6300098
6' W6300099
8' W6300100
3' W6300101
4' W6300102
5' W6300103
6' W6300104
8' W6300084
3' W6300105
4' W6300091
4' W6300127
5' W6300106
6' W6300081
6' W6300126
8' W6300107
3' W6300108
4' W6300109
5' W6300110
6' W6300111
8' W6300112
3' W6300113
4' W6300082
5' W6300114
6' W6300115
8' W6300116
3' W6300117
4' W6300118
5' W6300119
6' W6300120
8' W6300121
3' W6300122
4' W6300083
5' W6300123
6' W6300124
8' W6300089
7
IGHT-HEDN, HEDN COMBO, HEDW-0508
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
Mark Cipriani
PAGE OF
?
1
1
01/09/06
A REVISED RATINGS; ADDED SHEET 2 4/10/07 JR
B Updated dwg: removed sheet 2; added limiter 3/3/08 JR
HEDN-02
W6300092
3' CASE WIRING DIAGRAM
BALLAST 125-01-3267
FULHAM LH4-120-L
L
LIGHT SWITCH
TIPPETTE
125-01-0311
L
MAIN
POWER
~208 / ~240 VAC - 50/60 HZ
SWITCH
125-01-0311
225-01-6950
8.6x33.7
473 WATTS
1.97 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
PACKTRONICS
CONTROLLER
225-01-3229
L
TEMP. CONTROL
6
4
2 1 5
P1
3 7
SENSOR
225-01-3228
225-01-6787T
19x18
342W
1.43 AMPS @ ~240VAC
GRIDDLE-#2-Bottom
225-01-6786T
11x18
198W
0.83 AMPS @ ~240VAC
SHELF- #1 -9.5"-TOP
CONTACTOR
SQUARE -D
8910DPA43V02
125-01-1001
PILOT LIGHT
175-01-1102C
L1
L2
N
G
BLACK # 14
RED # 14
WHITE # 14
SHELF LIGHTING
(1) FP21T5/830 3'
125-03-1130
SHELF
CANOPY
OVERHEAD LIGHTING
(1) FP21T5/830 3'
125-03-1130
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
LIGHT CIRCUIT= .39A 42W
GRN # 14
LOADING
208 V 240 V
L1
L2
4.1
3.7
4.6
4.2
NOTE:
CASE MUST
BE GROUNDED
1104W @ 240VAC
853W @ 208VAC
Wiring Diagrams
8
Rev. 0508
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
JESSE RIOS
---
PAGE OF1
1
4/19/07
B Updated dwg; added 225-01-1702 to griddle 1/28/08 JR
HEDN-02
W6300093
4' CASE WIRING DIAGRAM
BALLAST 125-01-3267
FULHAM LH4-120-L
LL
~208 / ~240 VAC - 50/60 HZ
SWITCH
125-01-0311
225-01-6787T
19x18
342WATTS
1.43AMPS @ 240 VAC
225-01-6787T
19x18
342WATTS
1.43AMPS @ 240 VAC
GRIDDLE-#2-Bottom
PACKTRONICS
CONTROLLER
225-01-3229
L
TEMP. CONTROL
SENSOR
225-01-3228
6
421 5
P1
3 7
PILOT LIGHT
175-01-1102C
225-01-6954
8.6x45.7
642 WATTS
2.68 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
SHELF- #1 -9.5"-TOP
LIGHT SWITCH
TIPPETTE
125-01-0311
CONTACTOR
SQUARE -D
8910DPA43V02
125-01-1001
15 AMP FUSE
125-01-3282
FUSE HOLDER
125-01-3283
SHELF
CANOPY
OVERHEAD LIGHTING
(1) FP28T5/830 4'
125-03-1133
SHELF LIGHTING
(1) FP28T5/830 4'
125-03-1133
L1
L2
N
G
LIGHT CIRCUIT= 56W.52A
BLK # 14
RED # 14
WHT # 14
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
LOADING
208 V 240 V
L1
L2
L3
5.3
4.8
6.1
5.5
NOTE:
CASE MUST
BE GROUNDED
1382W @ 240VAC
1054W @ 208VAC
Wiring Diagrams (Cont'd)
9
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
PAGE OF1
2
4/19/07
HEDN-02
W6300094
5' CASE WIRING DIAGRAM
BALLAST 125-01-3267
FULHAM LH4-120-L
L
L
~208 / ~240 VAC - 3Ø - 50/60 HZ
SWITCH
125-01-0311
225-01-6958
8.6x57.7
810 WATTS
3.38 AMPS @ 240 VAC
SHELF- #1 -9.5"-TOP
225-01-6787T
19.0x18.0
342 WATTS
1.43 AMPS @ 240 VAC
225-01-6786T
11.0x18.0
198 WATTS
0.83 AMPS @ 240 VAC
225-01-6787T
19.0x18.0
342 WATTS
1.43 AMPS @ 240 VAC
PILOT LIGHT
125-01-1102C
LIGHT SWITCH
TIPPETTE
125-01-0311
15 AMP FUSE
125-01-3282
FUSE HOLDER
125-01-3283
CONTACTOR
SQUARE -D
8910DPA43V02
125-01-1001
PACKTRONICS
CONTROLLER
225-01-3229
L
TEMP. CONTROL
SENSOR
225-01-3228
6421 5
P1
3 7
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
GRIDDLE-#2-Bottom
OVERHEAD LIGHTING
(1) FP35T5/830 5'
125-03-1136
SHELF LIGHTING
(2) FP14T5/830 2'
125-03-1127
SHELF
CANOPY
BALLAST 125-01-3267
FULHAM LH4-120-L
CAP UNUSED RED LEAD
LIGHT CIRCUIT= .53A
L1L2L3
N
G
BLK # 14
RED # 14
WHT # 14
JESSE RIOS
LOADING
208 V 240 V
L1
L2
L3
6.7
6.1
7.6
7.1
NOTE:
CASE MUST
BE GROUNDED
Wiring Diagrams (Cont'd)
IGHT-HEDN, HEDN COMBO, HEDW-0508
10
Rev. 0508
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
PAGE OF2
2
4/19/07
HEDN-02
W6300094
5' CASE WIRING DIAGRAM
JESSE RIOS
L1
BLACK (BLK)
# 14
WHITE (W)
#14
N
L2
GREEN (G)
# 14
G
BK
RED (R)
# 14
L3
L
SWITCH
125-01-0311
CIRCUIT #1
BLUE
(BL)
R
BL
BLACK
WHITE
L
LIGHT SWITCH
TIPPETTE
125-01-0311
WHITE
RED
BALLAST 125-01-3267
FULHAM LH4-120-L
OVERHEAD LIGHTING
(1) FP35T5/830 5'
125-03-1136
SHELF LIGHTING
(2) FP14T5/830 2'
125-03-1127
SHELF
CANOPY
CAP UNUSED RED LEAD
LIGHT CIRCUIT= .53A
225-01-6958
8.6x57.7
810 WATTS
3.38 AMPS @ 240 VAC
SHELF- #1 -9.5"-TOP
225-01-6787T
19.0x18.0
342 WATTS
1.43 AMPS @ 240 VAC
225-01-6786T
11.0x18.0
198 WATTS
0.83 AMPS @ 240 VAC
225-01-6787T
19.0x18.0
342 WATTS
1.43 AMPS @ 240 VAC
PILOT LIGHT
125-01-1102C
PACKTRONICS
CONTROLLER
225-01-3229
L
TEMP. CONTROL
SENSOR
225-01-3228
64
21 5
P1
3 7
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
GRIDDLE-#2-Bottom
BALLAST 125-01-3267
FULHAM LH4-120-L
Wiring Diagrams (Cont'd)
11
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
JESSE RIOS
PAGE OF
?
121
4/19/07
HEDN-02
W6300095
6' CASE WIRING DIAGRAM
LIGHT SWITCH
TIPPETTE
125-01-0311
L
SWITCH
125-01-0311
~208 / ~240 VAC - 3Ø - 50/60 HZ
L
CONTACTOR
SQUARE -D
8910DPA43V02
125-01-1001
OVERHEAD LIGHTING
(2) FP21T5/830 3'
125-03-1130
PACKTRONICS
CONTROLLER
225-01-3229
L
TEMP. CONTROL
6421 5
P1
3 7
SHELF LIGHTING
(2) FP21T5/830 3'
125-03-1130
225-01-6962
8.6x69.7
979 WATTS
4.08 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
BALLAST 125-01-3267
FULHAM LH4-120-L
BALLAST 125-01-3267
FULHAM LH4-120-L
225-01-6787T
19x18
342 WATTS
1.43AMPS @ 240 VAC
GRIDDLE-#2-Bottom
SENSOR
225-01-3228
PILOT LIGHT
175-01-1102C
SHELF- #1 -9.5"-TOP
SHELVES
CANOPY
L1L2L3NG
BLK # 14
RED # 14
WHT # 14
225-01-6787T
19x18
342 WATTS
1.43AMPS @ 240 VAC
225-01-6787T
19x18
342 WATTS
1.43AMPS @ 240 VAC
LIGHT CIRCUIT= .7A
LOADING
208 V 240 V
L1
L2
L3
8.0
7.3
9.1
8.4
NOTE:
CASE MUST
BE GROUNDED
Wiring Diagrams (Cont'd)
IGHT-HEDN, HEDN COMBO, HEDW-0508
12
Rev. 0508
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
JESSE RIOS
PAGE OF
?
L1
BLACK (BLK)
# 14
WHITE (W)
#14
N
L2
GREEN (G)
# 14
G
BK
RED (R)
# 14
L3
L
SWITCH
125-01-0311
CIRCUIT #1
BLUE
(BL)
R
BL
BLACK
WHITE
L
LIGHT SWITCH
TIPPETTE
125-01-0311
WHITE
RED
LIGHT CIRCUIT= .7A
OVERHEAD LIGHTING
(2) FP21T5/830 3'
125-03-1130
SHELF LIGHTING
(2) FP21T5/830 3'
125-03-1130
BALLAST 125-01-3267
FULHAM LH4-120-L
BALLAST 125-01-3267
FULHAM LH4-120-L
SHELVES
CANOPY
PACKTRONICS
CONTROLLER
225-01-3229
L
TEMP. CONTROL
6421 5
P1
3 7
225-01-6962
8.6x69.7
979 WATTS
4.08 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
225-01-6787T
19x18
342 WATTS
1.43AMPS @ 240 VAC
GRIDDLE-#2-Bottom
SENSOR
225-01-3228
PILOT LIGHT
175-01-1102C
SHELF- #1 -9.5"-TOP
225-01-6787T
19x18
342 WATTS
1.43AMPS @ 240 VAC
225-01-6787T
19x18
342 WATTS
1.43AMPS @ 240 VAC
RED
HEDN-02
W6300095
6' CASE WIRING DIAGRAM
2
2
4/19/07
Wiring Diagrams (Cont'd)
13
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
JESSE RIOS
---
PAGE OF1
2
4/19/07
HEDN-02
W6300096
8' CASE WIRING DIAGRAM
L
LIGHT SWITCH
TIPPETTE
125-01-0311
L
~208 / ~240 VAC - 3Ø - 50/60 HZ
SWITCH
125-01-0311
225-01-6954
8.6x45.7
642 WATTS
2.68 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
225-01-6954
8.6x45.7
642 WATTS
2.68 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
225-01-6787T
19x18
342WATTS
1.43AMPS @ 240 VAC
225-01-6787T
19x18
342WATTS
1.43AMPS @ 240 VAC
SENSOR
225-01-3228
225-01-6787T
19x18
342WATTS
1.43AMPS @ 240 VAC
225-01-6787T
19x18
342WATTS
1.43AMPS @ 240 VAC
SENSOR
225-01-3228
OVERHEAD LIGHTING
(2) FP28T5/830 4'
125-03-1133
SHELF LIGHTING
(2) FP28T5/830 4'
125-03-1133
SHELVES
CANOPY
BALLAST 125-01-3267
FULHAM LH4-120-L
BALLAST 125-01-3267
FULHAM LH4-120-L
SHELF-9.5"-RIGHT-TOP
SHELF-9.5"-LEFT-TOP
GRIDDLE-RIGHT-BOTTOM
GRIDDLE-LEFT-BOTTOM
642
1 5
P1
3 7
TEMP. CONTROL
L
PACKTRONICS
CONTROLLER
225-01-3229
PILOT LIGHT
175-01-1102C
64
2 1 5
P1
3 7
TEMP. CONTROL
L
PACKTRONICS
CONTROLLER
225-01-3229
PILOT LIGHT
175-01-1102C
CONTACTOR
SQUARE -D
8910DPA43V02
125-01-1001
LIGHT CIRCUIT= .93A
L1
L2
L3NG
BLK # 14
RED # 14
WHT # 14
LOADING
208 V 240 V
L1
L2
L3
9.9
9.0
12.0
11.1
NOTE:
CASE MUST
BE GROUNDED
Wiring Diagrams (Cont'd)
IGHT-HEDN, HEDN COMBO, HEDW-0508
14
Rev. 0508
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
JESSE RIOS
---
PAGE OF2
2
4/19/07
HEDN-02
W6300096
8' CASE WIRING DIAGRAM
L1
BLACK (BLK)
# 14
WHITE (W)
#14
N
L2
GREEN (G)
# 14
G
BK
RED (R)
# 14
L3
L
SWITCH
125-01-0311
CIRCUIT #1
BLUE
(BL)
BLACK
WHITE
L
LIGHT SWITCH
TIPPETTE
125-01-0311
WHITE
RED
RED
225-01-6954
8.6x45.7
590 WATTS
2.46 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
225-01-6954
8.6x45.7
590 WATTS
2.46 AMPS @ 240 VAC
225-01-6787T
19x18
342WATTS
2.30AMPS @ 240 VAC
225-01-6787T
19x18
342WATTS
2.30AMPS @ 240 VAC
SENSOR
225-01-3228
225-01-6787T
19x18
342WATTS
2.30AMPS @ 240 VAC
225-01-6787T
19x18
342WATTS
2.30AMPS @ 240 VAC
SENSOR
225-01-3228
SHELF-9.5"-RIGHT-TOP
SHELF-9.5"-LEFT-TOP
GRIDDLE-RIGHT-BOTTOM
GRIDDLE-LEFT-BOTTOM
6421 5
P1
3 7
TEMP. CONTROL
L
PACKTRONICS
CONTROLLER
225-01-3229
PILOT LIGHT
175-01-1102C
6421 5
P1
3 7
TEMP. CONTROL
L
PACKTRONICS
CONTROLLER
225-01-3229
PILOT LIGHT
175-01-1102C
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
OVERHEAD LIGHTING
(2) FP28T5/830 4'
125-03-1133
SHELF LIGHTING
(2) FP28T5/830 4'
125-03-1133
SHELVES
CANOPY
BALLAST 125-01-3267
FULHAM LH4-120-L
LIGHT CIRCUIT= .93A
BALLAST 125-01-3267
FULHAM LH4-120-L
Wiring Diagrams (Cont'd)
15
IGHT-HEDN, HEDN COMBO, HEDW-0508
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
JESSE RIOS
PAGE OF
?
1
1
4/20/07
1
B Updated dwg; added 225-01-1702 to griddle 1/28/07 JR
HEDN-03
W6300086
3' CASE WIRING DIAGRAM
L
L
MAIN
POWER
~208 / ~240 VAC - 3Ø - 50/60 HZ
SWITCH
125-01-0311
BALLAST 125-01-3267
FULHAM LH4-120-L
BALLAST 125-01-3267
FULHAM LH4-120-L
225-01-6950
8.6x33.7
473 WATTS
1.97 AMPS @ 240 VAC
225-01-6951
10.6x33.7
583 WATTS
2.43AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
PACKTRONICS
CONTROLLER
225-01-3229
L
TEMP. CONTROL
SENSOR
225-01-3228
6421 5
P1
3 7
LIGHT SWITCH
TIPPETTE
125-01-0311
CONTACTOR
SQUARE -D
8910DPA43V02
125-01-1001
PILOT LIGHT
175-01-1102C
SHELF- #1 -9.5"-TOP
SHELF- #2 -11.5"
GRIDDLE-#3-Bottom
225-01-6787T
19.0x18.0
342 WATTS
1.43 AMPS @ 240 VAC
225-01-6786T
11.0x18.0
198 WATTS
0.83 AMPS @ 240 VAC
CAP UNUSED RED LEAD
OVERHEAD LIGHTING
FP21T5/830 3'
125-03-1130
SHELF LIGHTING
(2) FP21T5/830 3'
125-03-1130
SHELVES
CANOPY
L1
L2
L3
N
G
LIGHT CIRCUIT= .58A 63W
BLK # 14
RED # 14
WHT # 14
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
NOTE:
CASE MUST
BE GROUNDED
7.2
6.7
6.4
5.8
L1
L2
208 V 240 V
LOADING
1659W @ 240VAC
1264W @ 208VAC
Wiring Diagrams (Cont'd)
16
Rev. 0508
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
JESSE RIOS
PAGE OF
?
111
4/20/07
B Updated dwg; added limiter to griddle circuit 3/19/08 JR
HEDN-03
W6300097
4' CASE WIRING DIAGRAM
BALLAST 125-01-3267
FULHAM LH4-120-L
LL
~208 / ~240 VAC - 50/60 HZ
SWITCH
125-01-0311
BALLAST 125-01-3267
FULHAM LH4-120-L
225-01-6954
8.6x45.7
642 WATTS
2.68 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
225-01-6955
10.6x45.7
791 WATTS
3.30 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
225-01-6787T
19x18
342WATTS
1.43 AMPS @ 240 VAC
225-01-6787T
19x18
342WATTS
1.43 AMPS @ 240 VAC
GRIDDLE-#3-Bottom
PACKTRONICS
CONTROLLER
225-01-3229
L
TEMP. CONTROL
SENSOR
225-01-3228
6421 5
P1
3 7
SHELF- #1 -9.5"-TOP
SHELF- #2 -11.5"
PILOT LIGHT
175-01-1102C
CAP UNUSED RED LEAD
LIGHT SWITCH
TIPPETTE
125-01-0311
CONTACTOR
SQUARE -D
8910DPA43V02
125-01-1001
OVERHEAD LIGHTING
(1) FP28T5/830 4'
125-03-1133
SHELF LIGHTING
(2) FP28T5/830 4'
125-03-1133
SHELVES
CANOPY
LIGHT CIRCUIT=.78 A 84W
BLK # 14
RED # 14
WHT # 14
L1L2L3
N
G
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
LOADING
208 V 240 V
L1
L2
8.4
7.7
9.5
8.8
NOTE:
CASE MUST
BE GROUNDED
2280W @ 240VAC
1747W @ 208VAC
Wiring Diagrams (Cont'd)
17
IGHT-HEDN, HEDN COMBO, HEDW-0508
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
JESSE RIOS
PAGE OF
?
11 2
4/20/07
HEDN-03
W6300098
5' CASE WIRING DIAGRAM
BALLAST 125-01-3267
FULHAM LH4-120-L
L
L
~208 / ~240 VAC - 3Ø - 50/60 HZ
SWITCH
125-01-0311
BALLAST 125-01-3267
FULHAM LH4-120-L
CAP UNUSED RED LEAD
225-01-6959
10.6x57.7
999 WATTS
4.17 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
225-01-6958
8.6x57.7
810 WATTS
3.38 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
SHELF LIGHTING
(2) FP14T5/830 2'
125-03-1127
SHELF- #1 -9.5"-TOP
SHELF- #2 -11.5"
GRIDDLE-#3-Bottom
225-01-6787T
19.0x18.0
342 WATTS
1.43 AMPS @ 240 VAC
225-01-6786T
11.0x18.0
198 WATTS
0.83 AMPS @ 240 VAC
225-01-6787T
19.0x18.0
342 WATTS
1.43 AMPS @ 240 VAC
PACKTRONICS
CONTROLLER
225-01-3229
PILOT LIGHT
125-01-1102C
L
TEMP. CONTROL
SENSOR
225-01-3228
642
1 5
P1
3 7
LIGHT SWITCH
TIPPETTE
125-01-0311
CONTACTOR
SQUARE -D
8910DPA43V02
125-01-1001
OVERHEAD LIGHTING
(1) FP35T5/830 5'
125-03-1136
SHELVES
CANOPY
BALLAST 125-01-3267
FULHAM LH4-120-L
SHELF LIGHTING
(2) FP14T5/830 2'
125-03-1127
LIGHT CIRCUIT=.76 A
BLK # 14
RED # 14
WHT # 14
L1L2L3NG
LOADING
208 V 240 V
L1
L2
L3
10.5
9.7
12.0
11.2
NOTE:
CASE MUST
BE GROUNDED
Wiring Diagrams (Cont'd)
18
Rev. 0508
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
JESSE RIOS
PAGE OF
?
L1
BLACK (BLK)
# 14
WHITE (W)
#14
N
L2
GREEN (G)
# 14
G
BK
RED (R)
# 14
L3
L
SWITCH
125-01-0311
BLUE
(BL)
BLACK
WHITE
L
LIGHT SWITCH
TIPPETTE
125-01-0311
WHITE
RED
RED
225-01-6959
10.6x57.7
999 WATTS
4.17 AMPS @ 240 VAC
225-01-6958
8.6x57.7
810 WATTS
3.38 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
SHELF- #1 -9.5"-TOP
SHELF- #2 -11.5"
GRIDDLE-#3-Bottom
225-01-6787T
19.0x18.0
342 WATTS
1.43 AMPS @ 240 VAC
225-01-6786T
11.0x18.0
198 WATTS
0.83 AMPS @ 240 VAC
225-01-6787T
19.0x18.0
342 WATTS
1.43 AMPS @ 240 VAC
PACKTRONICS
CONTROLLER
225-01-3229
PILOT LIGHT
125-01-1102C
L
TEMP. CONTROL
SENSOR
225-01-3228
642
1 5
P1
3 7
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
BALLAST 125-01-3267
FULHAM LH4-120-L
BALLAST 125-01-3267
FULHAM LH4-120-L
CAP UNUSED RED LEAD
SHELF LIGHTING
(2) FP14T5/830 2'
125-03-1127
OVERHEAD LIGHTING
(1) FP35T5/830 5'
125-03-1136
SHELVES
CANOPY
BALLAST 125-01-3267
FULHAM LH4-120-L
SHELF LIGHTING
(2) FP14T5/830 2'
125-03-1127
LIGHT CIRCUIT=.76 A
2 2
4/20/07
HEDN-03
W6300098
5' CASE WIRING DIAGRAM
Wiring Diagrams (Cont'd)
19
IGHT-HEDN, HEDN COMBO, HEDW-0508
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
JESSE RIOS
---
PAGE OF1
1
4/20/07
B Updated dwg; removed sheet 2; added limiter to griddle 3/17/08 JR
HEDN-03
W6300099
6' CASE - WIRING DIAGRAM
PACKTRONICS
CONTROLLER
225-01-3229
L
TEMP. CONTROL
6421 5
P1
3 7
LIGHT SWITCH
TIPPETTE
125-01-0311
L
SWITCH
125-01-0311
~208 / ~240 VAC - 50/60 HZ
L
CONTACTOR
SQUARE -D
8910DPA43V02
125-01-1001
225-01-6963
10.6x69.7
1207 WATTS
5.03 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
225-01-6962
8.6x69.7
979 WATTS
4.08 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
BALLAST 125-01-3267
FULHAM LH4-120-L
BALLAST 125-01-3267
FULHAM LH4-120-L
BALLAST 125-01-3267
FULHAM LH4-120-L
PILOT LIGHT
175-01-1102C
225-01-6787T
19x18
342WATTS
1.43 AMPS @ 240 VAC
225-01-6787T
19x18
342WATTS
1.43 AMPS @ 240 VAC
GRIDDLE-#3-Bottom
SENSOR
225-01-3228
225-01-6787T
19x18
342WATTS
1.43 AMPS @ 240 VAC
SHELF- #1 -9.5"-TOP
SHELF- #2 -11.5"
OVERHEAD LIGHTING
(2) FP21T5/830 3'
125-03-1130
SHELF LIGHTING
(2) FP21T5/830 3'
125-03-1130
SHELVES
CANOPY
SHELF LIGHTING
(2) FP21T5/830 3'
125-03-1130
BLK # 14
RED # 14
WHT # 14
L1
L2
N
G
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
LIGHT CIRCUIT= 1.17A 126W
LOADING
208 V 240 V
L1
L2
12.7
11.6
14.5
13.4
NOTE:
CASE MUST
BE GROUNDED
Wiring Diagrams (Cont'd)
20
Rev. 0508
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
JESSE RIOS
---
PAGE OF1
1
4/20/07
B Add limiters to griddle circuits; revised wiring scheme 4/ 1/2008 JR
HEDN-03
W6300100
8' CASE WIRING DIAGRAM
L
LIGHT SWITCH
TIPPETTE
125-01-0311
L
~208 / ~240 VAC - 50/60 HZ
SWITCH
125-01-0311
225-01-6954
8.6x45.7
642 WATTS
2.68 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
225-01-6955
10.6x45.7
791 WATTS
3.30 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
225-01-6954
8.6x45.7
642 WATTS
2.68 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
225-01-6955
10.6x45.7
791 WATTS
3.30 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
BALLAST 125-01-3267
FULHAM LH4-120-L
BALLAST 125-01-3267
FULHAM LH4-120-L
BALLAST 125-01-3267
FULHAM LH4-120-L
OVERHEAD LIGHTING
(2) FP28T5/830 4'
125-03-1133
SHELF LIGHTING
(2) FP28T5/830 4'
125-03-1133
SHELVES
CANOPY
SHELF LIGHTING
(2) FP28T5/830 4'
125-03-1133
SENSOR
225-01-3228
6
4
2 1 5
P1
3 7
TEMP. CONTROL
L
PACKTRONICS
CONTROLLER
225-01-3229
PILOT LIGHT
175-01-1102C
SHELF-9.5"-LEFT-TOP
SHELF-11.5"-LEFT
SHELF-9.5"-RIGHT-TOP
SHELF-11.5"-RIGHT
225-01-6787T
19x18
342WATTS
1.43 AMPS @ 240 VAC
SENSOR
225-01-3228
GRIDDLE-RIGHT-BOTTOM
6
4
2 1 5
P1
3 7
TEMP. CONTROL
L
PACKTRONICS
CONTROLLER
225-01-3229
PILOT LIGHT
175-01-1102C
225-01-6787T
19x18
342 WATTS
1.43 AMPS @ 240 VAC
SENSOR
225-01-3228
GRIDDLE-LEFT-BOTTOM
6
421 5
P1
3 7
TEMP. CONTROL
L
PACKTRONICS
CONTROLLER
225-01-3229
PILOT LIGHT
175-01-1102C
CONTACTOR
SQUARE -D
8910DPA43V02
125-01-1001
L1
L2L3N
G
LIGHT CIRCUIT= 1.56A 168W
BLK # 12
RED # 12
WHT # 14
BLUE # 12
225-01-6787T
19x18
342WATTS
1.43 AMPS @ 240 VAC
225-01-6787T
19x18
342 WATTS
1.43 AMPS @ 240 VAC
BLK # 12
RED # 12
BLUE # 12
GREEN # 12
BLK # 14
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
LOADING
208 V 240 V
L1
L2
L3
11.2
10.4
10.7
12.6
12.0
12.3
NOTE:
CASE MUST
BE GROUNDED
Wiring Diagrams (Cont'd)
21
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
Mark Cipriani
PAGE OF1
1
01/09/07
123
Eng\WIRESCHEMATICS\NEW-WIRING
HEDN-04
W6300101
3' CASE WIRING DIAGRAM
BALLAST 125-01-3267
FULHAM LH4-120-L
L
LIGHT SWITCH
TIPPETTE
125-01-0311
L1L2L3NG
L
MAIN
POWER
~208 / ~240 VAC - 1Ø - 50/60 HZ - 4W
125-01-1001
SQUARE -D
CONTACTOR
8910DPA43V02
SWITCH
125-01-0311
CANOPY
SHELVES
BALLAST 125-01-3267
FULHAM LH4-120-L
225-01-6951
10.6x33.7
536 WATTS
2.23 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
225-01-6950
8.6x33.7
435 WATTS
1.81 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
225-01-6952
12.6x33.7
637 WATTS
2.65 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
CASE LIGHTS
(4) FP21T5/830 3'
125-03-1130
15 AMP FUSE
125-01-3282
FUSE HOLDER
125-01-3283
PACKTRONICS
CONTROLLER
225-01-3229
PILOT LIGHT
175-01-1102C
L
TEMP. CONTROL
6421 5
P1
3 7
SENSOR
225-01-3228
225-01-6787T
19x18
342W
1.43 AMPS @ ~240VAC
GRIDDLE-#4-Bottom
225-01-6786T
11x18
198W
0.83 AMPS @ ~240VAC
SHELF- #1 -9.5"-TOP
SHELF- #2 -11.5"
SHELF- #3 -13.5"
LOADING
208 V 240 V
L1
L2
L3
9.5
7.7
~
11.0
8.9
~
NOTE:
CASE MUST
BE GROUNDED
GM
Wiring Diagrams (Cont'd)
IGHT-HEDN, HEDN COMBO, HEDW-0508
22
Rev. 0508
DATE:
PROJECT TITLE:
DRAWING #:
DRAWN BY:
PRODUCTION ORDER #:
DRAWING TITLE:
DATE:
Hussmann Corporation, Int'l.
13770 Ramona Avenue
Chino, CA. 91710
(909)-590-4910 Lic.#: 644406
REVISIONS:
#: DESCRIPTION:
CHECKED BY:
BY:
FILE LOCATION:
ECD
PAGE OF1
1
01/17/06
B Updated dwg; added limiter to griddle circuit 4/23/08 JR
HEDN-04
W6300102
4' CASE WIRING DIAGRAM
BALLAST 125-01-3267
FULHAM LH4-120-L
L
LIGHT SWITCH
TIPPETTE
125-01-0311
L
MAIN
POWER
~208 / ~240 VAC - 50/60 HZ
125-01-1001
SQUARE -D
CONTACTOR
8910DPA43V02
SWITCH
125-01-0311
GRIDDLE HEATING PADS
(2) 342W 1.43A @ 240 VAC
225-01-6787T
BALLAST 125-01-3267
FULHAM LH4-120-L
225-01-6954
8.6x45.7
642 WATTS
2.68 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
225-01-6955
10.6x45.7
791 WATTS
3.30 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
225-01-6956
12.6x45.7
940 WATTS
3.92 AMPS @ 240 VAC
THERMOSTAT
TEMPCO
TEB33000
225-01-1700
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
SHELF- #1 -9.5"-TOP
SHELF- #2 -11.5"
SHELF- #3 -13.5"
GRIDDLE-#4-Bottom
PACKTRONICS
CONTROLLER
225-01-3229
PILOT LIGHT
175-01-1102C
L
TEMP. CONTROL
SENSOR
225-01-3228
6421 5
P1
3 7
OVERHEAD LIGHTING
(1) FP28T5/830 4'
125-03-1133
SHELVES
CANOPY
OVERHEAD LIGHTING
(3) FP28T5/830 4'
125-03-1133
L1
L2NG
LIGHT CIRCUIT= 1.04A 112W
RED # 12
BLACK # 12
WHITE # 14
BLACK # 14
GREEN # 12
LIMIT SWITCH
TEMPCO TST-112-119
225-01-1702
GM
LOADING
208 V 240 V
L1
L2
12.1
11.1
13.8
12.8
NOTE:
CASE MUST
BE GROUNDED
3312W @ 240VAC
2517W @ 208VAC
Wiring Diagrams (Cont'd)
23
Loading...
+ 51 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use