NOTE: Be sure merchandisers have
been leveled according to the installation instructions. Carefully unpack and
inspect the CW2 Joint Kit, making
sure there is no
breakage or damage.
Be sure factory installed alignment pins
are in place.
NOTE: Apply gasketing to one case
only.
1
Apply Gaskets – 1 and 2
as shown in Figure 1.
• Remove paper backing as
gasket is applied.
• Apply tworowsof Gasket 1 to
the center flue foam area only.
• Lapgaskets at lower
corners.
• Check that there are no gaps
betweengasketandmerchandiser.
• Do not stretch gasket,
especially around corners.
• Do not butt gaskets; always
overlap joints.
®
CW2-GE/CW2-XGE
CW2U-GE/CW2U-XGE
CW2EGE/CW2EXGE
Joint Kit Instruction
Shop Around Medium Temperature Convertible Merchandisers
January 2001
P/N 419410A
JOINT
JOINT
KIT
KIT
1
PARTS LIST
Item No. Quantity Description
1. 2 Gasket
1
/
2
x
1
/
2
x 180 in.
2. 1 Donut Gasket
3. 8 Nut Retainer
5
/
16
-18
4. 8 Cap Screw
5
/
16
-18 x
3
/
4
5. 2 Cap Screw
5
/
16
- 18 x1
1
/
4
6. 2 Lock Washer Split Steel
5
/
16
7. 2 Flat Washer
5
/
16
8. 2 Hex Nut
5
/
16
- 18
9. 2 Joint Base Plate (end case only)
10. 12 Thread Cutting Flange Screw (end case only)
Splashguard Brackets
MUST BE INSTALLED
BEFORE PIPING CASE.
Figure 1. Installing Gaskets
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.)
CW2U-GE/CW2U-XGE
CW2-GE/
CW2-XGE
CW2-GE/
CW2-XGE
CW2EGE
CW2EXGE
ALL
MODELS
1
/2 x1/2 In. Gasket
1
Donut Gasket
2
1
2
2
P/N 419410A
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.)
2
A. Remove shelves (if installed).
B. Remove honeycomb at end
to be joined.
C. Lower light channels. See
Detail A.
D. Remove display racks and
pans.
E. Remove wire rack support.
F. Lift out interior back panel.
G. Remove front grille assembly.
See Details B and C.
Figure 2. Removing Parts
®
Merchandisers
C
Detail A.
B
F
E
A
Package
Guard
Channel
Bumper
FRONT
OF
CASE
Front
Glass
D
Return Air
Grille
Front
Grille
Assembly
Package
Guard
Interior
Glass
Interior
Glass
Panel
G
Detail C.
Detail B.
3
8
Z
X
Y
X
W
W
Parent Case
Z
Y
4
3
Detail D.
Detail E.
Parent Case
Unitized
Case
End
Case
5
6
7
Follow joining sequence using
appropriate cap screw, retainer,
and hex nut as shown above.
TIGHTEN IN SEQUENCE SHOWN.
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.)
Figure 3. Installing Retainer Clips, Fasteners and Joining Bolts
P/N 419410A
Shop Around Medium Temperature Convertible
Joint Kit Instruction
Cases should be pushed
tightly together guided by
alignment pins.DO NOT
pull together by bolts.
4
Install Nut Retainer – 3 and
3
/
4
in. Cap Screw – 4 at locations
shown in Figure 3.
Do not tighten fully.
BE SURE TO FOLLOW BOLTING
SEQUENCE CORRECTLY
.
5
Install 1
1
/
4
in. Cap Screw – 5
Lock Washer – 6,
Flat washer – 7 and
Hex Nut – 8.
Start at the bottom locations.
Tighten the joints in the order
shown, W first, then at the center
uprights X, then canopies Y, and
then Z.
See drawing and Details D and E for
installation sequence and locations.
3
Move the first two cases to be
joined together and into position
against each other matching
Alignment Pins with the corresponding holes.
CAUTION
!
END CASE
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.)
4
P/N 419410A
Figure 4. Attaching Joint Plates to End Case
FOR END CASE ONLY:
6
Attach Joint Base Plate – 9
to the legs on both sides of the
end case joint using
Screws – 10. See Figure 4
and Detail F.
Joint
Base
Plate
9
10
FRONT OF END CASE
Detail F.
9
Joint
Base
Plate
FRONT OF CASE
10
End Case
Leg
®
Merchandisers
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.)
5
Shop Around Medium Temperature Convertible
Joint Kit Instruction
P/N 419410A
7
Slide the alignment strips
between front glass sections at
each joint. See Figure 5.
8
Refer to the installation instructions to install the splashguard
brackets.
Figure 5. Inserting the Alignment Strips
Alignment Strip
Loading...