Full-Auto Electric Washing Machine
Model: DWF-7589/8089
INSTRUCTION MANUAL
■First applying the Air Bubble Washing System in the world.
■Applying One-Touch Operation System.
■Realizing calm washing through the innovational low-noise
design.
■Before operating this washer, please read this instruction
completely. Thank you
The First Air Bubble Washing
System in the World
CONTENTS Page
➣Your washer is equipped with the
bubble generator that generates a
great deal of air bubble.
➣The air bubbles knock the dirt out
of the clothes during wash and
they push up the heavy dirt to
remove it during rinse.
➣Because the double washing
method using both air bubble &
water current is applied to this
washer, wash efficiency is excellent
in comparison with the original
washer system.
A NOTE TO YOU
Thank you for buying a DAEWOO appliance.
DAEWOO washers are easy to use, save time, and help you manage your home better.
This manual contains valuable information about how to operate and maintain your washer properly and safely.
Please read it carefully.
PARTS AND FEATURES.........................................................2
WASHER SAFETY...................................................................3
INSTALLATION INSTRUCTIONS...........................................4
ELECTRICAL REQUIREMENTS............................................5
INLET HOSE CONNECTION..................................................6
OPERATING YOUR WASHER...............................................7
THE FUNCTIONS OF THE CONTROL PANEL...................8
WASHING PROCEDURE AND COURSE SELECTION
GENERAL PROCEDURE FOR OPERATION....................11
CARING FOR YOUR WASHER...........................................12
HOW TO CLEAN THE FILTER............................................13
REMOVING STAINS.............................................................14
TROUBLE SHOOTING.........................................................15
SPECIFICATION...................................................................16
........9
PARTS AND FEATURES
The parts and features of your washer are illustrated on this page.
Become familiar with all parts and features before using your washer.
NOTE
The drawings in this book may vary from your washer model.
•
They are designed to show the different features of all models covered by this book,
Your model may not include all features.
• HOT WATER TAP
After using the washer, close the water tap.
In case of the single valve model,
there is no hot water valve.
• COLD WATER TAP
After using the washer,
close the water tap
• SOFTENER INLET
• BLEACH INLET
• CONTROL PANEL
• POWER SWITCH
• PULSATOR
• ADJUSTABLE LEG
• DETERGENT CASE
ACCESSORIES
DRYTEN (OPTION) COVER UNDER (OPTION) WATER TAP ADAPTER INLET HOSE
• LINT FILTER
• GROUND WIRE
In case of 3-wire
power cord, ground
wire will not be
provided
• POWER CORD
• HOSE DRAIN
DRYTEN
UP
HOSE DRAIN (FOR NON-PUMP) HOSE DRAIN CLAMPHOSE DRAIN (FOR PUMP) CONNECTOR INLET(OPTION)
2
WASHER SAFETY
Save these instructions
Your safety is important to us.
To reduce the risk of fire, electrical shock, or injury when using your washer, follow
basic precautions including the following:
Read all instructions before using your washer
• Flammable fluids (dry-cleaning solvents,
kerosene, gasoline, etc.) should not be
used or stored in or near your washer.
Do not add flammable fluids to your wash
water.These substances give off vapors
that can create a fire hazard or explosion.
• Do not allow children to operate, play
with, or crawl on or inside your washer.
Supervise children closely when your
washer is used near them.
• After starting a cycle, do not reach into
the spin basket unless all motion stops.
• Do not tamper with the controls.
Please ...
• Have only a qualified person install, repair,
or replace parts on washer.
• Maintain washer properly.
• Protect washer from the weather and
keep it where the temperature will not fall
below freezing.
• Do not install the washer at a place of
extremely high humidity. It could cause an
Electrical shock or a short circuit.
• Connect washer to the correct outlet,
electrical supply, water supply, and drain.
• Ground washer properly.
Understanding your responsibilities
• Do not wash items that are soiled with vegetable or cooking oil.
These items may contain some oil after laundering.
Due to the remaining oil, the fabric may smoke or catch fire by itself.
• Do not use chlorine bleach and ammonia or acid (Such as vinegar or rust remover) in the
same wash. Hazardous fumes can form.
• Unplug power supply cord before attempting to service your washer.
• Do not wash fiberglass materials.
Small particles can stick to fabrics and cause skin irritation.
• Do not use hot water that temperature is over 50
It can cause a deformation of plastic parts.
• Do not spray water on the control panel and back cover of the washer.
It can cause a fire or an electric shock.
°C (120°F).
3
4
INSTALLATION INSTRUCTIONS
Location of washer
Check location where washer will be installed. Make sure you have everything
necessary for correct installation.
Proper installation is your responsibility.
•Do not place or store your washer below 0°C (32°F) to avoid any damage from freezing.
•Install the washer on the horizontal solid floor.
C
If the washer is installed on an unsuitable floor, it could
make considerable noise, vibrate and cause a malfunction.
If washer is not level, adjust the front leg(A) up or down for
horizontal setting.
•Earthed electrical outlet(B) is required with 20cm of
UP DOWN
B
A
bottom back of washer cabinet.
•Hot and cold water faucets (C) must be within 1M of the
upper back of the washer cabinet and provide water
pressure 0.3kgf/cm
2
-8kgf/cm2 (2.94N/cm2-78.4cm2).
Drain system
Never forget to install drain hose before operating your washer.
The packing box is opened, there are a drain hose, and a hose clamp in the washer.
Non-Pump Model Pump Model
• Connect the drain hose to the drain outlet
at the back side of the washer, and fasten
it tightly with the clamp attached.
Hose clamp
Drain hose
NOTES
• The opening must not be obstructed by carpeting when the washing machine is
installed on a carpeted floor.
• Connect the drain hose to the drain outlet
at the back side of the washing machine,
and fasten it tightly with the clamp
supplied.
Drain Outlet
Drain hose
Hose Clamp
4
`5
Non-Pump Model
1In case that it goes over
a door sill.
Don’t let the height of
the drain hose exceed
2In case of extending the
drain hose.
Don’t let the total length
exceed 3m.
20cm from the bottom
of washer.
20Cm
Pump Model
Laundry tub drain system Standpipe drain system
• Top of tub must be at least 86cm
(34inches) high and no higher than 130cm
from bottom of washer (A)
A
3Be careful that the end
of the drain hose is not
immersed in water.
3m
• Needs a 3cm minimum diameter
standpipe with minimum carry away
capacity of 30liters per minute.
• Top of tub must be at least 86cm
(34inches) high and no higher than 130cm
from bottom of washer (B)
B
ELECTRICAL REQUIREMENTS
WARNING
•
Electrical earth is required on this washer
•
If it does not fit the outlet, have a proper outlet
installed by a qualified electrician.
C
electrical shock hazard:failure to follow these instructions could result in
death or serious injury.
•
Don’t earth to a gas pipe
•
Don’t change the power supply cord plug.
•
Check with a qualified electrician if you are not
sure the washer is properly earthed.
Recommended earthing method
For your personal safety, this washer must be earthed.
This washer is equipped with a power supply cord (A) having a
earthing plug (B). To minimize possible shock hazard, the cord must
be plugged into a mating earthing-type wall receptacle (C).
If a mating wall receptacle is not available, it is the personal
B
A
responsibility and obligation of the customer to have the proper
earthed wall receptacle installed by a qualified electrician.
5
6
INLET HOSE CONNECTION
Be careful not to confuse hot water inlet and cold water inlet.
In using only one water tap or in case of attached one water inlet valve, connect the
inlet hose to the cold water inlet valve.
For Ordinary Tap
1Pull down the collar of
the inlet hose to separate
it from the water tap
adapter.
4Remove the tape, and
screw connector B into
connect A tightly.
Connector A
Connector B
2Loosen the four screws
properly in fitting into
water tap.
5Connect the inlet hose to
the water tap adapter by
puling down the collar of
the hose end.
3
Fit the water tap adapter
into the water tap tap
and tighten the four
screws evenly while
pushing up the adapter
so that the rubber
packing can stick to the
water tap tightly.
TAPE
6Connect the inlet hose
adapter of the hose to
the water inlet of the
washer by turning it
clockwise to be fixed
tightly.
• Please check the rubber
packing inside the inlet hose
adapter of the hose.
For Screw-Shaped Tap
Connect the inlet hose to
1 2 3
the water tap by
screwing the connector
tightly.
Rubber
Connector
Hose
Packing
Connector
Connect the connectorinlet supplied if
necessary.
Connector
inlet
Connector
Hose
Rubber
Packing
Connector
6
Insert the inlet hose
adapter into the water
inlet of a washer and turn
it to be fixed.
*Cheek the packing in the inlet
7
OPERATING YOUR WASHER
To obtain the best wahing results, you must operate your washer properly.
This section gives you this important information.
Preparing clothes for washing
• Close zippers, snaps, and hooks to avoid
snagging other items.
Remove pins, buckles, and other hard
objects to avoid scratching the washer
interior.
• Empty pockets and turn them inside out.
• Turn down cuffs and turn synthetic knits
out to avoid pilling.
• Tie strings and sashes so they will not
tangle.
• Treat spots and stains.
(see "Removing stains" on page14)
Sorting
• Separate heavily soiled items from, lightly soiled ones, even if they would normally be
washed together.
• Separate dark colors from light colors, colorfast items from non-colorfast item.
Loading
• Drop items into washer loosely. Items
should move easily through wash water
for best cleaning and wrinkle-free results.
• Load washer properly and select correct
load size setting.
Overloading and selecting a setting too
small for the wash load can:
- cause poor cleaning
- increase wrinkling
- create excessive lint
- wear out items faster (because of pilling)
• Mix large and small items in each load.
Load evenly to maintain washer balance.
An off balance load can make the washer
vibrate during spin.
• Reduce wash time when using a small
load size setting. Loads with only a few
small items need less wash time.
• Use a large load size setting to reduce
wrinkling with permanent press clothes
and some synthetic knits. These items
should have more room to move in the
water than heavy items (towels, jeans)
7
`8
THE FUNCTIONS OF THE CONTROL PANEL
POWER
WASH
TEMP.
WATER
LEVEL
RES
WASH TEMP. DETERGENT
HOT
COLD
WASH
TEMP.
HIGH
MEDIUM
LOW
SMALL
WATER
LEVEL
FUZZY
BLANKET
ECONOMY
SUIT
SOAK
COURSE
REMAIN
RES.
RES.
MIN.
RINSE
CONTROL
ONLY SPIN
SPRAY RINSE
PROCESS
SPINWASH
POWER
START
HOLD
• Press this switch to turn the power on or off.
• It can be used to choose water temperature to be supplied.
• As the button is pressed, water temperature will be repeated.
COLD ➝COLD+HOT ➝HOT
• In case of the single valve model, there is no wash temperature
selector function.
• It can be used to adjust amount of water according to the size of the
load to be washed.
• As the button is pressed, water level is selected by
MEDIUM ➝ HIGH ➝ SMALL ➝ LOW
• It can be used to pre-engage time for wash.
PROCESS
CONTROL
ONLY SPIN
COURSE
START/
HOLD
• It is the button for the partial process or the combination of each
process (wash, rinse, spin) (See page 10)
• If you want to change wash time, rinse times, spin time, you must
press this button after selecting each process by the process button.
Also, this button can be used to spin only. (See page 10)
• It can be used to select the full-automatic course.
• As the button is pressed, course will be selected by following order:
FUZZY ➝BLANKET ➝ECONOMY ➝SUIT(WOOL) ➝SOAK
• Operation and temporary stop is repeated as it is pressed.
• When you want to change course in operating;
press the "START/HOLD" button➝Select the course that you want to
change ➝press the "START/HOLD" button again.
8
`9
WASHING PROCEDURE AND COURSE SELECTION
FULL AUTOMATIC COURSE
1. FUZZY COURSE (SENSOR);
• This selection is for general washing except extraordinary clothes.
• Artificial brain sensor selects properly the various kind of washing condition such as
washing time, rinse times, spin time and water level.
POWER
START
HOLD
2. BLANKET COURSE;
• This selection is effective for blanket, curtain, carpet, etc ...
• Do not wash general-electric blanket absolutely. (4kg’s limitation for one-time-wash)
Procedure to press the button;
POWER
COURSE
adjust to
"BLANKET"
adjust to water
level and water
temperature
START
HOLD
3. ECONOMY COURSE;
• This selection is useful to reduce water consumption and washing time for less dirty
clothes.
Procedure to press the button;
POWER
COURSE
adjust to
"ECONOMY"
adjust to
water level and
water temperature
START
HOLD
4. SUIT(WOOL) COURSE
• This selection is effective for suit clothes. (1.2kgs limitation for 1 time-wash)
•Do not put leather clothes, or chamois clothes into the washing tub for washing.
It may cause shrinkage or deformation to the clothes.
• Please use the neutral detergents only.
• The water temperature is fixed to COLD
• The water level LOW&SMALL is not selected.
POWER
COURSE
adjust to
"SUIT(WOOL)"
Put the exclusive
detergent DRYTEN
of 26g into the tub
for dilution with water.
START/
HOLD
After dissolving of
detergent, lamp
will buzzer will
sound.
Put the clothes into
the tub after the
buzzer sounds.
START/
HOLD
Close the lid and press the
S/H button once again.
5. SOAK COURSE;
• This selection is effective for blue-jean, climbing clothes, ruck sack, sports wear, etc...
• If you want to soak, press the course button to adjust to "SOAK" .
POWER
COURSE
adjust to
"SOAK"
adjust to
water level and
water temperature
START
HOLD
9
`10
Reserved Washing
• Reservation can be made from 2 hours to 48hours.
example) Tomake reservation to complete washing in 8hours.
COURSE
adjust to
"the Res"
• Now the reservation is made.
REMAIN
MIN
RES.
"--" SHALL BLINK
RES
adjust to "8"
PARTIAL PROCESS & COMBINATION
POWER
REMAIN
RES.
MIN
close
the lid
START
HOLD
PROCESS
CONTROL
ONLY SPIN
PROCESS
CONTROL
ONLY SPIN
PROCESS
CONTROL
ONLY SPIN
WASH TIME CONTROL
• As the control button is pressed, wash time will be repeated as
following;
18 ➝ 0 ➝ 6 ➝ 10min.
14
➝
• If you dont want wash process, you must adjust wash time to 0 min.
RINSE TIMES CONTROL
• As the control button is pressed, Rinse times will be repeated as
following;
1) Pump Model 2 Rinse
2) Non-Pump Model 2 Rinse
2 Spray Rinse ➝ 3 Spray Rinse ➝ 4 Spray Rinse ➝ 0 Rinse ➝ Rinse
➝
3 Rinse ➝ 4 Rinse ➝ 0 Rinse ➝ 1 Rinse
➝
3 Rinse ➝ 4 Rinse ➝ 1 Spray Rinse
➝
• If you dont want Rinse process, you must adjust Rinse times to 0 times.
• If you select spray Rinse, the LED of spray Rinse is lighted
(NON-PUMP MODEL)
SPIN TIME CONTROL
• As the control button is pressed, spin time will repeated as following;
5
➝7 ➝ 9 ➝ 0 ➝ 1 ➝
3min.
• If you dont want spin process, you must adjust spin time to 0 min.
START
HOLD
CONVINIENT OPERATION FOR SPIN ONLY
• If you want spin only, it is convinient to operate
the button as following.
10
POWER
CONTROL
ONLY SPIN
START
HOLD
`11
GENERAL PROCEDURE FOR OPERATION
1. Add measured detergent to the washer, (Follow manufacturer’s directions for safe use)
2. OPTIONAL STEP
If desired, add measured liquid chlorine bleach to the bleach inlet. use only liquid chlorine
in the bleach inlet
* Follow manufacturer’s direction for safe use.
NOTE
•
Do not let bleach splash, drip, or run down into washer
basket.
Undiluted bleach will damage any fabric it touches.
•
Bleach inlet
(Symbol)
Do not use this dispenser to add powdered chlorine or
color safe bleach to your wash load. The dispenser is for
liquid chlorine bleach use only.
3. OPTIONAL STEP
If desired, add measured liquid fabric softener to the softener inlet.
• Pour liquid fabric softener into the dispenser using the amount recommended on the
package. Avoid dripping or spilling any fabric softener on the load.
Softener inlet
(Symbol)
• The dispenser is for liquid fabric softener use only.
4. Close the washer lid (door)
5. Press the power button.
6. Select the cycle. The full automatic cycle has five settings; FUZZY, BLANKET, ECONOMY,
SUIT(WOOL), SOAK. (See page 9)
7. Press the START/HOLD button.
11
`12
CARING FOR YOUR WASHER
Proper care of your washer can extend its life. This section explains how to care for
your washer properly and safely.
Cleaning your washer
Exterior Interior
Wipe up detergent, bleach, and other spills
with a soft, damp cloth or sponge as they
occur. Occasionally wipe the outside of the
washer to keep it looking like new one.
Do not put sharp or metal object in your
washer, they can damage the finish. Check all pockets for
pins, clips, money, bolts, nuts, etc.
Do not lay these objects on your washer after emptying
pockets.
Clean interior with 250ml of chlorine bleach
mixed with 500ml of detergent.
Run washer through a complete cycle.
Repeat process if necessary.
Winter storage or moving care
Install and store your washer where it will not freeze. Because some water may stay in the
hoses, freezing can damage your washer.
If storing or moving your washer during freezing weather, winterize it.
To winterize washer To use washer again
• Turn off water faucet.
• Disconnect and drain water inlet hoses
• Run washer on a drain and spin setting
(see page 10) for 1 minute.
• Unplug the power supply cord.
• Flush water pipes and hoses.
• Reconnect water inlet hoses.
• Turn on water faucet.
• Reconnect power supply cord.
Non-use or vacation care
Operate your washer only when you are at home.
If will be on vacation or not using your washer for an extended period of time, you should:
• Unplug the power supply cord or turn off eletrical power to the washer.
• Turn off the water supply to the washer.
This helps avoid accidental flooding (due to a water pressure surge) while you are away.
12
13
HOW TO CLEAN THE FILTER
Cleaning the Lint Filter
1Pull the Fiter frame up-
ward.
2Turn the lint filter inside
fout, wash to the lint of
with water
Lint Filter
Filter Frame
3Return the filter as it was,
and insert the filter frame
into the slot
Cleaning the water inlet filter
• Clean the filter when water leaks from, the water inlet.
1Pull the power
plug out before
cleaning it.
2Turn off the water
supply to the
washer and
3Pull the inlet filter
out.
4Remove the dirt
from the inlet
filter with a brush.
sperate the inlet
hose.
Cleaning the drain filter
• In case "Pump-Model" drain hose, this filter’s equipped at the back side of washer.
• This drain filter is to screen the foreign stuffs such as threads, coins, pins, buttons etc ...
• If the drain filter is not cleaned at proper time (every 10 times of use), Drain problem could
be caused.
1Put down the remained
water in the hose. And
2Turn the cap counter 3Pull out the filter
clockwise.
put a container under the
filter to collect water.
CAP
CONTAINER
FILTER
4Clean the drain filter. 5Put in the filter along the
guiding prominence of
the case. Please note the
left position of the filter
adjusting the groove to
CAP
the guide rib.
FILTER
CAP
CASE
GUIDE
RIB
SUIT
13
assembly.
FILTER
CASE
CAP
6Turn the cap clockwise
tightly.
CAP
14
REMOVING STAINS
Stained, heavily-soiled, or greasy items may need to be prewashed or soaked for best results.
Soaking helps remove protein-type stains like blood, milk, or grass. Prewashing helps loosen
soil before washing.
Stain removal rules
• Use warm water for soaking or prewashing stained laundry. Hot water can set stains.
• Most stains are easier to remove when they are fresh. Old or set stains may not coconut
• Before treating any stain, find out what kind of stain it is, how old the stain is, what kind of
fabric it is, and if the fabric is color fast. (Check the care label)
• Washing and drying can set some stains.
• Start with cold or warm water, hot water can set some stain.
• When bleach is recommended, use a bleach that is safe for the fabric.
• Put the stained area face down on a paper towel or white cloth. Apply the stain remover
to the back of the stain. This forces the stain off fabric instead of through it.
Stain removal guide
STAIN TO REMOVE
Blood
Chewing gum
Cocoa, Chocolate
Coffee
Cream/Milk
Ice cream
Deodorant
Egg
Fabric/Softener
Fruit stains
Grass
Grease and oil
Iron or rust
Lipstick
Mildew
Mud
Paint-oil based
Paint-water based
Scorch marks
Rinse immediately in COLD water.
If stain remains, soak in cold water with an enzyme prewash.
Use ice in plastic bag to harden the gum.
Scrape off what you can and then sponge with white spirits.
Sponge with COLD water and soak in an enzyme prewash.
If stains persist, rub in a little detergent and rinse in cold water.
Blot up quickly and rinse out in COLD water.
Rub in a little detergent and wash in the maximum temperature allowed for the
fabric type.
Rinse in COLD water and wash normally.
If stain is still apparent, sponge with white spirits.
Rub affected area with white vinegar and then rinse under running COLD water.
Sponge with white spirits.
Treat stiffened areas with enzyme prewash
Soak in a COLD enzyme prewash, rinse and wash normal.
Rub affected area with bar soap and wash normally.
Treat as soon as pressible by sponging with COLD water.
Rub a little detergent on the stain and wash normally
Sponge with white sprites.
Rub in an enzyme prewash and wash as normal
Lay the affected area face down on an absorbent cloth and work from the back.
Sponge with white spirits or dry cleaning fluid. Wash normally.
Apply lemon juice and salt and place in the sun. Wash normally.
Sponge with white methylated spirits and wash normally.
Wash in WARM water and detergent.
Moisten area with lemon juice, dry in the sun and wash normally.
If stain persists and the fabric allows, use a bleach.
Brush off any dry mud. Rinse in cold water.
If stain persists rub in a little detergent and wash normally.
Scrape off any fresh paint and sponge with a non flammable dry cleaning fluid
and wash normally.
Treat while still wet, rinse in WARM water and wash normally.
Dampen a cloth with hydrogen peroxide, lay it over the affected area and press
with a fairly hot iron.
14
15
TROUBLE SHOOTING
Most problems are easily solved if you understand the cause.
Check the following list for problem befor calling for service.
Before calling for service, check these
PROBLEM CHECK POINT
• The washer will not
operate at all.
• Is there a power failure?
• Is the power cord correctly connected to an electric outlet?
• Is the electric fuse broken?
• Did you turn on the power?
• Did you press Start/Hold button?
• Is there correct amount of water in the tub?
Water is not supplied;
•
If water supply is not finished within 20
minutes, the lamp will light up, and
the buzzer will sound to indicate a problem.
• The washer will not drain;
If the drain is not finished within selected
time, lamp will light up, and the buzzer
will sound to indicate a problem.
• The washer will not spin;
If the clothes is collected on one side
during spin and the tub becomes
unbalanced, the spin operation will be
interrupted, and then this unbalanced
condition will be corrected by following
operation: WATER SUPPLY fi RINSEfi
DRAIN However if the unbalanced
condition is unchanged despite repeating
the above operation, the lamp will
light up, and the buzzer will sound to
indicate a problem.
• Did you connect the inlet hose and open the water tap?
• Is the inlet hose or the water tap frozen?
• Is the water supply shut off?
• Does foreign matter block up the inlet hose filter?
• Is the drain hose frozen or blocked up by dirt?
• Is the drain hose kinked or deformed?
• Is the end of the drain hose immersed in water?
• Is there excessive dirt inside the pump housing?
• Is the clothe in the tub collected on one side?
• Is the washing machine installed on an uneven floor or is the
vibration serious?
• Is the lid open?
(The lamp will light up in this case.)
•
These cases are not malfunctions
•
The sound "wing" heard during water supply is the operating sound made by the water
inlet valve.
•
The sound "sha" heard in stopping the tub is the sound that comes from the
autobalancer of the tub.
15
SPECIFICATIONS
NO. ITEM DWF-1089 DWF-9289 DWF-8089 DWF-7589
1 POWER SOURCE AVAILABLE IN ALL LOCAL AC VOLTAGE AND CYCLE
50Hz
2
POWER CONSUMPTION
MACHINE NON-PUMP
3
WEIGHT PUMP
4 DIMENSION (WXHXD) 628 X 1005 X 673mm 610 X 962 X 655mm
5 WASHING COURSE
6
WATER CONSUMPTION
7
WATER LEVEL SELECTOR
8
OPERATING WATER PRESSURE
60Hz WASH : 145~160, SPIN : 750~800
REVOLUTION
9 50Hz WASH : 130~145, SPIN : 700~750
PER MINUTE
SILK, DRY
COURSE
10 PULSATOR 6 WINGS (Ø396mm) 6 WINGS (Ø376mm)
430W
55Kg (GROSS : 64Kg)
56Kg (GROSS : 65Kg)
NORMAL 315L
HIGH(96L), MID(81L)
LOW(65L), SMALL(49L)
E.SMALL(36L)
60Hz
480W
(FUZZY, MEMORY, DRY, SILK, ECONOMICAL, STRONG, NIGHT, BLANKET)
50Hz
430W
54Kg (GROSS : 63Kg)
55Kg (GROSS : 64Kg)
NORMAL 304L
HIGH(93L), MID(78L)
LOW(61L), SMALL(48L)
E.SMALL(33L)
0.3kgf/cm2~8kgf/cm
60Hz
480W
FULL AUTOMATIC 8 COURSE
2
(2.94 N/cm2~78.4N/cm2)
WASH : 70 (60Hz), 60 (50Hz)
50Hz
400W
50Kg (GROSS : 60Kg)
51Kg (GROSS : 61Kg)
NORMAL 265L
HIGH(82L), MID(70L)
LOW(57L), SMALL(43L)
E.SMALL(31.5L)
60Hz
460W
50Hz
400W
49Kg (GROSS : 59Kg)
50Kg (GROSS : 60Kg)
NORMAL 259L
HIGH(80L), MID(68L)
LOW(55L), SMALL(42L)
E.SMALL(30.5L)
60Hz
460W
11
WATER LAVEL CONTROL
12 ANTI NOISE PLATE O O O O
13
GEAR MECHANISM ASS’Y
14 LINT FILTER O O O O
15 SOFTENER INLET O O O O
16
FUNCTION FOR SOAK WASH
17 ALARM SIGNAL O O O O
18
RESIDUAL TIME DISPLAY
19
AUTO. WATER SUPPLY
20 NEW WATER FLOW WATER FLOW FOR ADJUST THE UNBALANCED LOAD
21 ECONOMIC COURSE O O O O
22
FUNCTION FOR BUBBLE
23
AUTO RE-FEED WATER
24 AUTO POWER OFF O O O O
OOOO
OOOO
OOOO
OOOO
OOOO
ELECTRONICAL SENSOR
HELICAL GEAR FOR LOW NOISE
Loading...