Husqvarna DS160C User Manual 2

DS160C

Asia Pacific

Manuel d’utilisation et d’entretien Manuale di Istruzioni Foreuse de chantier Trapanatrice da cantiere

Manual de Instrucciones Operating Instructions Taladradora de obra Drilling Machine

Betriebs-und Wartungsanleitung Gebruiksaanwijzing Baustellen-Bohrmaschine Verplaatsbare Boormachine

Manual de Instrucoes Bruksanvisning och Underhallsmanual Perfuradora de obra Borrmaskin

113

114

WARNING

Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

·Lead from lead-base paints,

·Crystalline silica from bricks and cement and other masonry products and

·Arsenic and Chromium from chemically treated lumber.

Your risk from these exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

·REFER TO MANUAL·

115

PREFACE TO THE MANUAL

These operating instructions apply exclusively to drill stand, type DS 160 C. Please also read the operating instructions that accompany your drill motor to verify their compatibility and not to exceed the limitations of the DS 160 C drill stand.

Usage to the Intended Purpose

The drill stand is designed exclusively for core drilling in concrete, asphalt, brickwork or similar building materials. Details of the maximum permissible drill bit diameter can be found under “Technical Specifications”. Any use above and beyond the intended purpose endangers both user and machine and is not permitted.

Before commencing drilling, always ensure that;

there is no danger of drilling through electric cables, gas, oil or other pipes, the drilled holes do not undermine the stability of the structure, you do not drill into or through any steel girders, when drilling through walls, you cannot cause any damage at the drill exit point. Strict care must be taken when drilling in areas where people or general public are present. Local codes dictate proper protocol and must be observed.

Improper Usage

The drill stand must not be used for any kind of stirring, e.g. paint or similar; drilling holes in soil, e.g. to drill holes for posts.

The drill stand must be mounted via anchor bolt or vacuum, do not attempt to drill hand held or standing on base plate.

This drill stand incorporates the expertise of decades of experience in the field of concrete drilling.

Before leaving our factory every machine passes an inspection program in which everything is checked completely.

Following the instructions will ensure that your machine gives long service, in normal operating conditions.

The user advice and spare parts mentioned in this document are given as an indication and do not constitute an undertaking. No warranty will be granted in the event of errors or omissions or for damage occurring during delivery or caused by the design or use of this machine. We are very concerned about the quality of our products and we serve the right to make any technical modifications to improve them without warning.

This document will assist the user particularly in:

·Information about the machine

·Information about its possible uses

116

·Prevent accidents due to unsuitable use, by an untrained person, during maintenance, repairs, overhauls, handling or transport

·Improve the reliability and durability of the machine

·Ensuring correct use, regular maintenance and rapid repair in order to reduce stoppage times and repair cost.

The manual should always be available at the place of work. It should be read and used by any person installing or using the machine. The obligatory technical regulations in force in the county where the machine is used must also be adhered to for maximum safety.

GENERAL SAFETY INSTRUCTIONS

The use of symbols on the drill stands and in the manual identify advice concerning your safety.

This symbol indicates that the machine is in conformance with the applicable European directive.

WARNING

MANDATORY

PROHIBITED

INFORMATION

These signs give advice concerning your safety.

SPECIAL INSTRUCTIONS

·The drill stand is designed to provide safe and reliable service in operating conditions corresponding with the instructions, but it can present dangers for the user and risks of damage, consequently regular on site inspection is necessary to ensure:

·Perfect technical condition (use for the purpose for which it is intended and taking into account any risks and correction of any malfunction detrimental to safety).

·Use of a diamond core bit for water lubricated cutting of concrete, asphalt, marble, stone,

granite, brick and facings (porcelain, glazed tiles, ceramics, etc). The use of any other core

bit is forbidden (abrasive, saw, etc).

117

·Competent staff (qualifications, age, training) who have read and understood the

manual in detail before starting work: any electrical, mechanical or other problem should be investigated by a qualified maintenance engineer (electrician, maintenance manager, approved dealer, etc).

·That the warnings and instructions marked on the machine are followed (adequate

personal protection, correct use, general safety instructions, etc).

·That no modification, transformation or addition is detrimental to safety and that it is

carried out without prior authorization from the manufacturer.

MOTORS:

DIMAS: DM 225D with motor support collar WEKA: DK 12 with motor support collar

DM 225 with motor support collar DK 13 with motor support collar

DK 14 with motor support collar

CARDI: Talpa T0 with motor support collar

Talpa T1 with motor support collar

Motor characteristics: see the manufacturer’s manual supplied with the motor.

Please contact us regarding any other frame/motor combination.

1. Delivery

On delivery, carry out an immediate visual check for signs of physical damage and that no components are missing. The contents of the package should include: Drill Stand - Base, Column, Carriage, Crank, Wheel Assembly, Vacuum Cap Plate, Vacuum Gasket and Back Support, Operating Instructions and Ordered Accessories.

2. Technical Specifications

Base length 15.50 in / 394 mm Base width 9.50 in / 241 mm Height 32 in / 813 mm Weight 30 lbs / 14 kg Motor rating up to max. 3.5 hp / 2.4 kW Drill bit diameter up to max. 6 in / 152 mm Impact anchor; minimum tensile force 5.7 kN with M12 Fastener

118

3. Assembly

Align holes on the wheel assembly (1) with the tapped holes on rear of the base plate (2). Insert bolts (3) through lockwashers (4), then insert bolts through wheel assembly and screw onto base plate.

4. Description and Features of the Drill Stand

Tapered roller carriage. Sealed ball bearing design. Plumb and leveling guides. Left and right crank handle drive with incorporated adjustment tool. This adjustment tool adjusts column angle, leveling screws and column angle lock. Angle column capability. Anchor base with incorporated vacuum capability. Detachable wheel assembly. Replaceable wear items. Incorporated carrying handle. Column angle and drill depth indicator decal. Rigid drill collar motor mount. Brass inserts for leveling bolts. Precision rack and pinion drive.

5. Handling - Transport

Remove the diamond core bit from the drill motor. Remove the motor from the carriage assembly. Lower the carriage to the base and lock the brake. The transport wheels enable the drill stand to be moved easily. Tilt the drill stand backwards and hold the handle at the top of the column. To avoid damaging the motor shaft, the motor must not be carried or moved by the shaft, whether or not it is fitted with a drill or extension. If the base is to be used as a vacuum mount, do not move the drill stand laterally or damage and tearing away the vacuum seal may result. To avoid deforming the seal, remove the seal when vacuum is not in use.

6. Inspection Before Starting Up

Please read the instructions for use prior to operating the machine for the first time.

The working area must be completely cleared, well lit and all safety hazards removed (no water or dangerous objects in the vicinity).

The use of ear protection is mandatory.

1 3

119

The operator must wear protective clothing appropriate to the work he is doing. We recommend that this includes both eye and ear protection.

Any person not involved in the work should leave the working area.

Use core bits which are suitable for the work to be done.

7. Fitting and Removing the Motor

Unplug the motor from the outlet.

Always remove the core bit before fitting or removing the motor.

Engage the carriage brake. The motor is mounted on the frame by means of a support collar.

8. Electrical Connection

ELECTRICAL SAFETY:

Operate this machine only on a supply equipped with a 30 mA grounded currentlimiting circuit breaker. The Ground Fault Circuit Interrupter (GFCI) must be used correctly, including testing it regularly. For tools supplied with an integral GFCI in the cable or in the main plug, if the cable or plug has been damaged, repairs must be carried out by the manufacturer, one of his agents or by a qualified repair workshop to avoid any risks resulting from errors.

Use single phase 2 pole plus grounded sockets for the appropriate voltage. Make sure that the main voltage is the same as that on the manufacturer’s plate. Extension cables, type HO7 RNF, should have an adequate cross section for the power: 3 x 2.5 mm

up to 50 m or double for longer cables.

9. Mounting Methods

There are three options available for fastening the base plate of your drill stand. Fastening with threaded rod and heavy-duty anchor, expanding anchor or vacuum.

120

+ 16 hidden pages