C 3000 / C 5500
EN Operator's manual 2-8
ES-MX Manual del usuario 9-15
FR-CA Manuel d’utilisation 16-22
Contents
Introduction..................................................................... 2
Safety..............................................................................4
Installation.......................................................................5
Operation........................................................................ 5
Maintenance................................................................... 6
Troubleshooting.............................................................. 6
Technical data................................................................ 7
Warranty......................................................................... 8
Introduction
Owner responsibility
WARNING: Cutting, especially when DRY
cutting, generates dust that comes from the
material being cut, which frequently contains
silica. Silica is a basic component of sand,
quartz, brick clay, granite and numerous
other minerals and rocks. Exposure to
excessive amount of such dust can cause:
Respiratory disease (affecting your ability to
breath), including chronic bronchitis, silicosis
and pulmonary fibrosis from exposure to
silica. These diseases may be fatal;
Skin irritation and rash.
Cancer according to NTP* and IARC* */
National Toxicology Program, International
Agency for Research on Cancer.
Take precautionary steps:
Avoid inhalation of and skin contact with
dust, mist and fumes.
Wear and ensure that all bystanders wear
appropriate respiratory protection such as
dust masks designed to filter out
microscopic particles. (See OSHA 29 CFR
Part 1926.1153)
To minimize dust emissions, wet cut when
feasible. If dry cutting is necessary, use an
appropriate dust extractor.
It is the owner’s/employer’s responsibility that the
operator has sufficient knowledge about how to use the
product safely. Supervisors and operators must have
read and understood the Operator’s Manual. They must
be aware of:
• The products’s safety instructions.
• The products’s range of applications and limitations.
• How the product is to be used and maintained.
National/Local regulations could restrict the use of this
product. Find out what regulations are applicable where
you work before you start using the product.
Product description
When the dust extractor is started, dust laden air is
sucked through the inlet valve at high speed through the
suction hose. The air is slowed down by the cyclone and
large dust particles are separated. Fine dust particles
continue to through the hose to the dust extractor. The
separated dust accumulates in the cyclone. When the
dust extractor is switched off, the dust falls through the
bottom flap into the plastic dust bag.
The separated dust accumulates in the cyclone. When
the dust extractor is switched off, the dust falls through
the bottom flap into the plastic dust bag.
Intended use
The pre-separator C 3000 / C 5500 is intended for
commercial use.
The product is intended for pre-separating dry, noncombustible dust.
2 819 - 002 - 23.11.2018
Product overview C 3000 / C 5500
91
91
95
5
2 2
3
4
3
4
1. To dust extractor
2. To grinder
3. Longopac holder
4. Longopac dust bag
5. Toggle fastner
Symbols on the product
Please read the operator’s manual carefully
and make sure you understand the
instructions before using the product.
Unhealthy dust can be spread during filter
change. Accordingly, the user should wear
protective glasses, protective gloves, and a
breathing mask conforming to protection
class FFP3.
WARNING! Dust can cause injuries if
inhaled. Use an approved breathing mask.
Avoid inhaling exhaust fumes. Always
provide for good ventilation.
819 - 002 - 23.11.2018 3
Product liability
As referred to in the product liability laws, we are not
liable for damages that our product causes if:
• the product is incorrectly repaired.
• the product is repaired with parts that are not from
the manufacturer or not approved by the
manufacturer.
• the product has an accessory that is not from the
manufacturer or not approved by the manufacturer.
• the product is not repaired at an approved service
center or by an approved authority.
Safety
Safety definitions
Warnings, cautions and notes are used to point out
specially important parts of the operator's manual.
WARNING: Used if there is a risk of injury or
death for the operator or bystanders if the
instructions in the manual are not obeyed.
CAUTION: Used if there is a risk of damage
to the product and/or the attachment, other
materials or the adjacent area if the
instructions in the manual are not obeyed.
Note: Used to give more information that is necessary in
a given situation.
Safety introduction
WARNING: Always be careful and use
common sense. This section describes the
basic safety instructions for using the
product. This information is never a
substitute for professional skills and
experience. If you get into a situation where
you feel unsafe, stop and contact an
authorized technichian. Do not attempt any
task that you are not sure of!
General safety instructions
WARNING:
Please read the safety
regulations and the complete operator's
manual carefully before using the preseparator. This manual is only for the preseparator C 3000 / C 5500.
• Make sure that you read and understand the
instructions for the product to make sure that you
know what personal equipment to wear, what safety
equipment to use and how to operate the product
safely.
Safety instructions for operation
WARNING: The pre-separator can only be
used with dry, non-explosive materials.
WARNING: Never allow children or other
persons not trained in the use of the product
to use or service it. Never allow anyone else
to use the product without first ensuring that
they have read and understood the contents
of the operator’s manual.
WARNING: Make sure the assembly area is
firm, so the product does not tip over. Risk of
personal and material injury.
WARNING: Do not move the product by
pulling the hose.
WARNING: Always use genuine
accessories.
WARNING: Risk of pinching when handling
the toggle fastener.
Safety instructions for maintenance
All spare parts used for the pre-separator C 3000 / C
5500 must be original spare parts.
WARNING:
Shut off and disconnect any
attached products before maintenance is
done on the pre-separator.
WARNING: Dust that can be dangerous to
health and can be spread out when cleaning
the product. Wear protective glasses,
protective gloves, and a breathing mask in
protection class FFP3.
4 819 - 002 - 23.11.2018
WARNING: Do not make holes in the
Longopac bag. Risk of dust dispersion.
Installation
General
When unpacking the product, check for damage and
that the accessories are included:
• Hose with end fittings
If any of the accessories are missing, please contact
your local distributor or a sales representative.
Operation
Introduction
The pre-separator must be attached to a dust extractor
with the correct capacity.
To connect the product
Connect the appropriate pre-separator to the grinder
and dust extractor according to the illustration. The
outlet on the top should be connected to the dust
extractor (A) and the inlet on the front should be
connected to the grinder (B). On the C 3000 the shorter
hose length provided with the pre-separator should be
used between the pre-separator and dust extractor.
A B
To assemble a new Longopac dust
bag
WARNING: Always clean the prefilter before
change of bag collection system.
Note: The dust extractor has Longopac system.
1. Put the dust bag in the holder.
2. Attach the dust bag holder to the container by
twisting it on to the holding pins.
819 - 002 - 23.11.2018 5
3. Pull the bag up from the bag holder and put it around
the container.
4. Tighten a strap around the bag and the container to
secure the bag to the container.
5. Pull the dust bag over the bag holder.
6. Close the bottom of the dust bag with a cable tie.
Maintenance
Introduction
When cleaning and doing service on the product,
disconnect the product from the dust extractor.
• The product must be cleaned before the product is
moved from the work area.
• All other equipment must be seen as contaminated.
• Use a cleaning room if it is possible.
• Correct personal protective equipment must be
used.
• All parts that are contaminated must be correctly
discarded in plastic bags after maintenance is done.
Refer to unhealthy dust such as silica dust.
Troubleshooting
Troubleshooting
Issue Cause Solution
Unsatisfactory suction Damages on the hose Replace the hose
The top cover is loose Adjust the top cover
Dirt in the flap to the dust bag Clean the flap
WARNING: Use
personal protective
equipment
Sealing is defective Replace the sealing
The toggle latches are loose Tighten the toggle latches
6 819 - 002 - 23.11.2018
Technical data
Technical data
Model C 3000 C 5500
Main Hose diameter, in./ mm 2.5 / 63 3 / 76
Main Hose length, ft / m 8.25 / 2.5 33 / 10
Inlet diameter, in./ mm 2.5 / 63 3 / 76 Camlock
Outlet diameter, in. / mm 2.5 / 63 3 / 76 Camlock
Dust Collection system, Type Longopac Longopac
Weight uncrated, lbs / kg 49 / 22 101 / 46
Dimensions (L*W*H), in. / mm 23.2x28.8x62.2 /
590x730x1580
23.6x28.3x64.5 /
600x720x1640
Volume, gal / l 10 / 37 26 / 100
819 - 002 - 23.11.2018 7
Warranty
Warranty
New equipment sold by Husqvarna is warranted to be
free from manufacturing defects in normal service for a
period of one (1) year from date of purchase by the
original consumer purchaser*. Component
manufacturers offer separate warranty periods. Call
Technical Services at (800) 365-5040 for complete
information.
Husqvarna´s obligation under this warranty is expressly
limited to the replacement or repair at Husqvarna
Construction Products, or at a service facility designated
by us, of such part or parts as inspection shall disclose
to have been defective.
This warranty does not apply to defects caused by
damage, unreasonable use, faulty repairs made by
others or defects caused by failure to provide
reasonable maintenance, while in the possession of the
consumer. Further, the warranty is void if the product, or
any of its components, is altered or modified by the
consumer or if the product is used in an inappropriate
manner or with a blade not recommended by the
manufacturer.
(*) Husqvarna offers a 1-year warranty on all equipment
with the following exceptions:
• Large flat saws - 2 years (Diesel and gasoline
powered flat saws > 30 hp)
• DM 280/DM 340/DM 650 core drill motors - 2 years
• PG 530/PG 680/PG 820 (all variants, including RC) 2 years, or 1,000 hours (whichever comes first)
• Blade Clutch on large flat saws - 6 months
Wear items are not covered under warranty:
• Belts
• Bearings**
• Cart wheels
• Filters
• Wheels***
• Wear pads
• Spark plugs
(**) Except IntelliSeal System
(***) Except delamination
8
819 - 002 - 23.11.2018
Loading...