OWNER/OPERATOR
MANUAL
BACKPACK SPRAYER
BP4E
U
S
BP4E
WARNING
This sprayer is not designed to
be used with acids of any kind,
corrosive products like caustic
soda, gasoline, materials
capable of generating heat, hot
uids, explosive or highly
volatile products.
USE OF THESE AND OTHERS
EXPOSE USERS TO SERIOUS
INJURY AND EVEN DEATH.
WARNING
Before using our products,
please read this manual
carefully to understand the
proper use of your unit.
US-1
BP4E
SAFETY FIRST
Instructions contained in warnings within this manual and warning seals marked
with a symbol on the sprayer concern critical points which must be taken
into consideration to prevent possible serious bodily injury, and for this reason
you are requested to read all such instructions carefully and follow them without
fail.
Note that there may be times when warning seals peel off or become soiled and
impossible to read. If this happens, you should contact the dealer from which
you purchased the product to order new seals and afx the new seal(s) in the
required location(s).
NOTES ON TYPES OF WARNINGS
Contents
Instructions labeled as shown at left, concern critical steps or procedures
which must be followed in order to prevent accidents which could lead to
serious bodily injury or death.This mark is used to indicate instructions
which must be followed without exception.
IInstructions labeled as shown at left concern steps or procedures which, if not
followed correctly, could lead to mechanical failure, breakdown, or damage.
Used to label supplementary instructions designed to provide hints or directions
useful in the use of the product.
US-2
1. Parts location...................................................................3
2. Specications ..................................................................3
3. Warning labels on the machine .......................................3
4. For safe operation ...........................................................3
5. Set up ..............................................................................6
6. Pre Operation ..................................................................7
7. Operation.........................................................................7
8. Maintenance ...................................................................8
9. Storage ...........................................................................8
10. Disposal...........................................................................8
1. Parts location
BP4E
2. For safe operation
3
5
4
“The distinctive tank shape is a registered trademark of SP
Systems’ afliate, US Sprayer Holding Co., LLC, and licensed
exclusively to SP Systems for use with SP Systems’ registered
“large mouth” trademarks.”
6
7
1
1. Tank
2. Pump
2
3. Lid (cap)
4. Shoulder Strap
5. Hose
6. Wand
7. Nozzle,
Spray Tip Set
2. Specications
Type ................................................................... Back Pack
Model Name....................................................... BP4E
Dimensions (LxWxH).......................... 530x360x210 (20.9x14.2x8.3) mm (in)
Dry Weight........................................................................... 5.2 (10.4) kg (lbs)
Tank capacity................................................................... 15.1 (4.0) litter (Gal)
Max. Pressure............................................................10.5 (150) kgf/cm (psi)
Working Pressure.......................................... 1.05 - 5.6 (15 - 80)kgf/cm (psi)
2
2
Sealed/O rings............................................................................. VITON/Nytril
Pump Type.....................................................Piston/Diaphragm/Agitation
Reparability............................................................................. YES
Tank Mouth .................................................................................................. 6”
Wand Type ...................................................................................... 20” Brass
Standard Nozzle .................................................................Adjustable Nozzle
3. Warning labels on the machine
1. Read this Sprayer Owner/Operator
Manual carefully. Be sure you
understand how to operate this unit
properly before you use it. Failure to
do so could result in serious injury.
2. Be sure to keep this manual handy
so that you may refer to it later
whenever any questions arise. Also
note that you are requested to
contact the dealer from whom you
purchased the product for
assistance in the event that you
have any questions which cannot be
answered herein.
3. Always be sure to include this
manual when selling, lending, or
otherwise transferring the
ownership of this product.
4. Do not lend or rent your machine
without the owner’s manual.
5. Be sure that anyone using your unit
understands the information
contained in this manual.
6. Never let a child under 13 years old
use the machine.
7. DO NOT use ammables in the
sprayer. They can ignite or explode
causing serious injury.
8. Always wear splash goggles and
protective gear and clothing when
lling, using and/or cleaning the
sprayer.
9. Oil the rubber cap gasket prior to
rst usage so the gasket will seal
properly.
10.Tighten all connections before using
the sprayer. Some may not he
properly secured and must be
tightened to prevent leakage.
U
S
If warning label peel off or become soiled and impossible to read,
you should contact the dealer from which you purchased the
product to order new labels and afx them in the required
location(s).
Never modify your machine.
We will not warrant the machine, if you use the remodeled
machine or you don’t observe the proper usage written in the
manual.
BEFORE USING:
Oil cap gasket, oil check valve, and
keep breather hole clear of debris.
Your failure to oil and to clean check
valve, and to keep breather hole
opening to allow air into tank, can cause
tank to collapse and crack due to
vacuum created by the pump.
US-3
BP4E
4. For safe operation
1. Refrain from operating the sprayer if you
are tired, ill, or upset, or if you are under
the inuence of alcohol, drugs or
medication.
2. To reduce the risk of injury when lling,
using and/or cleaning the sprayer, always
wear eye protection. Eye protection should
meet the requirements of ANSI Z87.1.
3. Always wear a mask or respirator when
lling, using and cleaning sprayer, if
recommended by the spray material
manufacturer.
4. Wear protective gear and clothing when
lling, using and cleaning the sprayer.
5. Wear sturdy rubber-soled shoes or shoes
with some other form of anti-slip protection
to help protect you against falling when
lling, using and/or cleaning the sprayer.
6. Do not wear loose clothing, scarves, neck
chains, hair longer than shoulder length,
and the like when lling, using and/or
cleaning the sprayer.
Check and follow the local regulations.
• When planning your work schedule, allow
plenty of time to rest. Limit the amount of
time over which the product is to be used
continuously to somewhere around 30 ~ 40
minutes per session, and take 10 ~ 20
minutes of rest between work sessions.
Also try to keep the total amount of work
performed in a single day under 2 hours or
less.
Hose clamps are not completely tight.
Please tighten hose clamps prior to using.
Hose clamps are left loose to extend life of
gaskets and ttings.
Oil cap gasket before using and lubricate
weekly so the gasket will seal properly
and prevent chemical leaks.
Oil check valve and keep breather
hole clear of debris. Your failure to oil may
cause the tank to collapse and crack
due to vacuum created by pump lubricate
with “3 and 1” oil.
WORKING CONDITION
WORKING PLAN
USING THE PRODUCT
1. Always inspect your sprayer thoroughly
before and after each use. Check to be
sure hose is securely attached and in
good condition before pressurizing the
tank.
2. Check the work area that the sprayer will
be used in and remove or cover all
valuables that may be damaged by using
sprayer.
3. To reduce the risk of injury,
• Watch out for children, pets, open
windows or freshly washed cars, and
spray safely away.
• Do not allow bystanders in work area.
• Do not point the sprayer nozzle in the
direction of people or pets.
• Pay attention to the direction of the
wind, do not work against the wind.
• Never use the sprayer during windy
conditions.
• Never point a sprayer nozzle toward an
open ame to avoid the possibility of
igniting the unit, causing injury to
yourself or damage to surroundings.
• Always release pressure in the pump
prior to lling, cleaning, or servicing the
sprayer.
• Before opening a container of pesticide
or other spray material, carefully read,
understand, and follow all instructions
on the label.
• Do not use ammable materials in the
sprayer: they can ignite and/or
explo de, causing serious injury.
• Never use caustic or corrosive materials
in the sprayer, which could result in
damage to the unit.
• In case of personal contamination:
remove contaminated clothing, remain
upright, do not consume liquids or
cause vomiting, and get professional
help immediately.
• Never attempt to pressurize the unit by
any other method than with the pump
module provided.
Never over-pressurize the unit.
• Do not eat, drink, or smoke while
spraying.
• Wash face and hands with soap and
water after spraying.
• Clean and rinse tank and spraying
assembly after each use to prevent
rystallizing, which would later cause
clogging and chemical damage to the
unit.
• Do not store sprayer under pressure,
or with spray solution in tank.
• Do not transfer spray materials to other
containers, especially, food and/or
drink containers.
US-4
4. For safe operation
BP4E
• Keep spray materials locked up and
out of reach of children and animals.
• Use only original manufacturer’s
replacement parts.
• As a rule, mix your chemicals in a
separate container from which to ll the
sprayer. Do not mix formulas inside the
sprayer. Where an exception is made
(e.g. with liquid fertilizers), ll sprayer
with water BEFORE adding the active
ingredient.
• Always sift formula through the screen.
If there is no built-in strainer, use a
screened funnel.
• Never ll the sprayer with hot liquids.
Max. 30°C, or 85°F.
• Never use gasoline or other ammable
materials.
• Before cleaning or servicing the
sprayer, allow all pressure to escape.
Do not store or transport sprayer under
pressure.
• After each use, wash the sprayer—
including hose, lance and shut-off
valve—with plenty of fresh water.
Unless spraying is to be continued
within hours,
drain chemical formula and thoroughly
rinse the tank and all liquid ducts.
• Never store chemicals in your sprayer
for any length of time
• Do not leave the sprayer in reach of
children or persons not qualied to
handle it in proper fashion.
• When not in use—and especially
during prolonged storage—keep your
sprayer in a protected place away from
direct solar heat.
• Make sure the spray hose loops freely
without kinking or squeezing.
4. After using sprayers and other
equipment, CLEAN UP! Dispose of
debris in trash receptacles.
MAINTENANCE
1. In order to maintain your product in
proper working order, perform the
maintenance and checking operations
described in the manual at regular
intervals.
2. Examine the sprayer at intervals for
loose fasteners and rusted or damaged
parts.
Use special care for chemical leakage.
3. Clean and rinse tank and spraying
assembly after each use to prevent
crystallizing, which would later cause
clogging and chemical damage to the
unit.
4. All service except for those described in
this manual should be performed by
competent service personnel.
5. When replacing the any other part, or
any lubricant, always be sure to use only
Husqvarna products or products which
have been certied by Husqvarna for use
with the Husqvarna product.
6. In the event that any part must be
replaced or any maintenance or repair
work not described in this manual must
be performed, please contact a
Husqvarna authorized servicing dealer
for assistance.
7. Do not use any accessory or attachment
other than those bearing the Husqvarna
mark and recommended for the unit.
8. Under no circumstances should you ever
take apart the product or alter it in any
way. Doing so might result in the product
becoming damaged during operation or
the product becoming unable to operate
properly.
TRANSPORTATION
• Clean and rinse tank and spraying
assembly after each use to prevent
crystallizing, which would later cause
clogging and chemical damage to the
unit.
• Drain the content from the tank before
transporting or storing the sprayer.
• Secure the unit carefully to prevent
movement when it is transported.
• A unit that receives a strong shock
during transport and unloading may
malfunction.
STORAGE
• Clean and rinse tank and spraying
assembly after each use to prevent
crystallizing, which would later cause
clogging and chemical damage to the
unit.
• Do not store sprayer under pressure,
or with spray solution in tank.
• When storing the sprayer, choose a
space indoors free from moisture and
out of the reach of children.
DISPOSAL
• When disposing of your machine, or
chemical, be sure to follow your local
regulations.
U
S
US-5
BP4E
5. Set up
Hose clamps are not completely tight.
Please tighten hose clamps prior to using.
Hose clamps are left loose to extend life
of gaskets and ttings.
Oil cap gasket before using and
lubricate weekly so the gasket will seal
properly and prevent chemical leaks.
Oil check valve and keep breather
hole clear of debris. Your failure to oil
may cause the tank to collapse
and crack due to vacuum created by
pump lubricate with “3 and 1” oil.
HOW TO ASSEMBLE
1. Attach spray wand to spray gun and
tighten rmly.
2. Take pump handle RMKIT 7 and insert
into the tube on the pump lever RMKIT
5 (“T” shape lever on sprayer), you will
notice holes drilled through both sides
of both the pump handle and the pump
ever. Align these holes, take the “R”
pin provided and place through the
holes. This afxes the handle in place
and is ready for use.
For storage reverse process and then
place “R” pin through the pump lever
RMKIT to keep from losing “R” pin.
3. Instructions for installing shoulder strap
plastic buckle:
First put the sprayer on a hard at
surface, take the white plastic buckle
and while holding the sprayer up
slightly, place buckle under the tubular
metal frame. Slowly push down forcing
the frame into the buckle. Repeat the
same procedure for other side.
Fig. 1
Fig. 2
Fig. 13
Make sure to insert the locking pin for the
pump handle in its (only) CORRECT
POSITION.
The pin limits the pump stroke for
optimum performance.
Observe Fig. 1 exactly. (Fig. 2 and 3 spell
trouble.)
For best results and to maintain a good
seal, re-grease piston sleeve periodically
with vaseline or similar light lubricants.
US-6
BP4E
6. Pre-operation
Hose clamps are not completely tight.
Please tighten hose clamps prior to using.
Hose clamps are left loose to extend life of gaskets and
ttings.
Oil cap gasket before using and lubricate weekly so the
gasket will seal properly and prevent chemical leaks.
Oil check valve and keep breather hole clear of debris.
Your failure to oil may cause the tank to collapse and
crack due to vacuum created by pump lubricate with “3
and 1” oil.
Before using, oil cap gasket, felt pump washer, and check
valve, and maintain breather hole clear of debris. Your failure
to oil, clean check valve, and maintain breather hole open
to allow air into the tank, can cause the tank to collapse and
crack, due to vacuum created by pump.
1. Before you remove cap, be sure there is no pressure in the
tank. in order to release pressure, invert unit upside down
and squeeze spray pistol (aim away from you). Pressure will
escape; when hissing stops, all pressure has been
released. Remove pump assembly by turning
counter-clockwise. The pump handle has two locking
positions, one turning clockwise and one counter-clockwise.
2. Remove cap.
3. A unit that has been used with herbicides should never be
used to spray insecticides, unless the sprayer has been
properly cleaned and all other chemicals neutralized.
Failure to do this could cause you to kill plants that have
been sprayed. Consult with the manufacturer of the
chemicals in use to obtain proper instructions.
4. Always oil the gasket on the cap of the unit, as well as the
check valve. This will extend the life of the seal and is
important for obtaining a proper seal with no leaks.
5. Mix solution in a separate container, following the
manufacturers’ directions.
6. Pour pre-mixed solution through strainer into tank. Reinstall
cap tightly.
7. Place sprayer on back and pressurize tank by pumping
approximately 5 to 15 times.
8. You will need to pump occasionally to maintain the desired
spraying pressure.
9. For best results, the sprayer should be pumped every ve
seconds on a continuous basis. This will maintain your spra
ying pressure. If you do not pump, you will not have
pressure to spray.
7. Operation
• Always release pressure in the pump prior to lling,
cleaning, or servicing the sprayer.
• Before opening a container of pesticide or other spray mate
rial, carefully read, understand, and follow all instructions on
the label.
• Do not use ammable materials in the sprayer: they can
ignite and/or explode, causing serious injury.
• Never use caustic or corrosive materials in the sprayer,
which could result in damage to the unit.
HOW TO ADJUST THE NOZZLE
• To adjust nozzle, tighten cap (turn clockwise) for ne atomi
zed spray, or loosen (turn counter-clockwise) for coarser
spray or solid stream.
HOW TO PREPARE YOUR UNIT FOR USE
• For best results, the sprayer should be pumped every 5
seconds on a continuous basis. This will maintain your
spraying pressure. If you do not pump, you will not have
pressure to spray.
RECOMMENDED APPLICATIONS FOR
“LAWN AND GARDEN” OR “AGRICULTURE” USAGE.
Herbicide : Yes
Insecticides/Pesticides : Yes
Fertilizers : Yes
Chlorine (5%) : Yes, If cleaned (*)
Diesel : Yes
Wettable Powder : No
Stains & Sealers : Yes
Oil Based : Yes
Solvent-Based : Yes
Viscous : No
(*) Permanent damage will occur if sprayer is not cleaned
properly after each use with Chlorine
U
S
US-7
BP4E
8. Maintenance
Before you remove cap, be sure there is no pressure in the
tank. in order to release pressure, invert unit upside down
and squeeze spray pistol (aim away from you). Pressure
will escape; when hissing stops, all pressure has been
released.
Remove pump assembly by turning counter-clockwise. The
pump handle has two locking positions, one turning
clockwise and one counter-clockwise.
1. Remove cap and pour out remaining solution, then rinse all
parts thoroughly with clean water.
2. Add 1/2 gallon of fresh water in tank. Pressurize, and ush
pumping system by depressing trigger for at least two
minutes; then drain all remaining water.
• Periodically re-grease lid gasket as well as lid vent and pump
cylinder, where applicable.
• To ensure good performance, keep lid vent free of obstruc
tion.
Before and after each use, make sure all connections are
well tightened. Service and replace worn parts as required.
9. Storage
Never store chemicals in your sprayer for any length of
time.
1. Before you remove cap, be sure there is no pressure in the
tank. in order to release pressure, invert unit upside down
and squeeze spray pistol (aim away from you). Pressure will
escape; when hissing stops, all pressure has been
released.
Remove pump assembly by turning counter-clockwise. The
pump handle has two locking positions, one turning
clockwise and one counter-clockwise.
2. Remove cap and pour out remaining solution, then rinse all
parts thoroughly with clean water.
3. Add 1/2 gallon of fresh water in tank. Pressurize, and ush
pumping system by depressing trigger for at least two
minutes; then drain all remaining water.
4. Always store tank clean and empty in a dry, shaded location.
10. Disposal
Failure to follow manufacturer’s recommendation of use and
care of unit will void any expressed or implied warranty. Do
not use chlorine or clorox. It will permanently damage pump
system.
In the event that any part must be replaced or any
maintenance or repair work not described in this manual must
be performed, please contact a Husqvarna authorized servicing dealer for assistance.
SPRAYEAR MAINTENANCE TABLE
Daily
or
System/Compoment
Lid Gasket
Procedure
Grease
Before Use
3
After Use
When disposing of your machine, or chemical, be sure to
follow your local regulations.
US-8
Lid Vent
Pump
Connection
Whole unit
Inspect/Clean
Grease
Inspect/Tight
Wash/inspect
3
3
3
3
LIMITED WARRANTY
FOR TWO (2) YEARS OF HOME USE, ONE (1) YEAR FOR COMMERCIAL USE AND NINETY (90) DAYS FOR RENTAL
USE FROM THE DATE OF ORIGINAL PURCHASE,THE COMPANY, THROUGH ANY Husqvarna DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL PURCHASER, ANY PART OF PARTS FOUND TO BE
DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. THIS IS THE EXCLUSIVE REMEDY.
THE PURCHASER SHALL BEAR COSTS OF TRANSPORTING THE UNIT TO AND FROM THE Husqvarna DEALER.
THE PURCHASER SHALL NOT BE CHARGED FOR DIAGNOSTIC LABOR WHICH LEADS TO THE DETERMINATION
THAT A WARRANTED PART IS DEFECTIVE, IF THE DIAGNOSTIC WORK IS PERFORMED AT THE Husqvarna
DEALER.
THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE PERFORMANCE OF THE REQUIRED MAINTENANCE
AS DEFINED BY THE MANUFACTURER IN THE OWNER/OPERATOR MANUAL.
ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE, OR
WHICH IS SCHEDULED ONLY FOR REGULAR INSPECTION TO THE EFFECT OF “REPAIR OR REPLACE AS
NECESSARY” SHALL BE WARRANTED FOR THE WARRANTY PERIOD. ANY WARRANTED PART WHICH IS
SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE SHALL BE WARRANTED FOR THE PERIOD OF
TIME UP TO THE FIRST SCHEDULED REPLACEMENT POINT FOR THE PART.
ANY REPLACEMENT PART THAT IS EQUIVALENT IN PERFORMANCE AND DURABILITY MAY BE USED IN
NONWARRANTY MAINTENANCE OR REPAIRS, AND SHALL NOT REDUCE THE WARRANTY OBLIGATION OF THE
COMPANY.
BP4E
U
S
THE COMPANY IS LIABLE FOR DAMAGES TO OTHER COMPONENTS CAUSED BY THE FAILURE OF A
WARRANTED PART STILL UNDER WARRANTY.
THE WARRANTY DOES NOT APPLY TO THOSE UNITS WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF
INSTRUCTION LISTED IN THE OWNER/OPERATOR MANUAL FOR PROPER USE AND MAINTENANCE OF THE
UNITS, ACCIDENTAL MISHANDLING, ALTERATION, ABUSE, IMPROPER LUBRICATION, USE OF ANY PARTS OR
ACCESSORIES OTHER THAN THOSE SPECIFIED BY THE COMPANY, OR OTHER CAUSES BEYOND THE
COMPANY’S CONTROL.
THIS WARRANTY DOES NOT COVER THOSE PARTS REPLACED BY NORMAL WEAR OR HARMLESS
CHANGES IN THEIR APPEARANCE.
THERE ARE NO OTHER EXPRESS WARRANTIES.
IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE LIMITED TO TWO (2) YEARS OF HOME USE, ONE (1) YEAR FOR COMMERCIAL USE AND
NINETY (90) DAYS FOR RENTAL USE FROM THE ORIGINAL DELIVERY DATE.
LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL DAMAGE UNDER ANY AND ALL WARRANTIES ARE
EXCLUDED.
SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY
NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH
VARY FROM STATE TO STATE.
IF YOU NEED TO OBTAIN INFORMATION ABOUT THE NEAREST SERVICE CENTER, PLEASE CALL Husqvarna AT
1.800.487.5951.
DOCUMENTATION REQUIRED. YOU MUST MAINTAIN AND PRESENT PROOF OF PURCHASE (INCLUDING DATE,
PRODUCT MODEL AND, IF APPLICABLE, ENGINE SERIAL NUMBER) TO AN AUTHORIZED HUSQVARNA
SERVICING DEALER FOR WARRANTY SERVICE UNDER THIS LIMITED WARRANTY. PROOF OF PURCHASE RESTS
SOLELY WITH THE OWNER-CUSTOMER. HUSQVARNA ENCOURAGES YOU TO REGISTER YOUR PRODUCT
ONLINE AT www.usa.husqvarna.com TO HELP ENSURE, AMONG OTHER THINGS, THAT YOU CAN BE NOTIFIED
OF IMPORTANT PRODUCT INFORMATION. HOWEVER, REGISTERING YOUR PRODUCT IS NOT A CONDITION OF
WARRANTY SERVICE.
US-9
Loading...