Husqvarna 96143000601 User Manual
7021CH1
Owner’s Manual
532 19 53-49 01.03.05 BY Printed in U.S.A.
2
WARNING: Battery posts, terminals and
related ac ces so ries contain lead and lead
compounds, chemicals known to the State
of Cal i for nia to cause can cer and birth
defects or oth er re pro duc tive harm. Wash
hands after handling.
WARNING: Engine exhaust, some of its
con stit u ents, and certain vehicle com po -
nents contain or emit chem i cals known to
the State of Cal i for nia to cause can cer and
birth defects or oth er re pro duc tive harm.
CAUTION: Always disconnect spark plug
wire and place wire where it cannot contact
spark plug in order to prevent ac ci den tal
starting when setting up, trans port ing,
adjusting or making re pairs.
Look for this symbol to point out im-
por tant safety precautions. It means
CAUTION!!! BE COME ALERT!!! YOUR
SAFE TY IS IN VOLVED.
CAUTION: Muffl er and other engine parts
become extremely hot during operation
and remain hot after engine has stopped.
To avoid severe burns on contact, stay away
from these areas.
Safe Operation Practices for Walk-Behind Mowers
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE
TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
SAFETY RULES
I. GENERAL OPERATION
• Read, understand, and follow all instructions on the
machine and in the manual(s) before starting. Be thor-
ough ly familiar with the controls and the proper use of
the machine before starting.
• Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
• Only allow responsible individuals, who are familiar
with the instructions, to operate the machine.
• Clear the area of objects such as rocks, toys, wire,
bones, sticks, etc., which could be picked up and thrown
by the blade.
• Be sure the area is clear of other people before mow-
ing. Stop machine if anyone enters the area.
• Do not operate the mower when barefoot or wearing
open sandals. Always wear substantial foot wear.
• Do not pull mower backwards unless absolutely nec-
es sary. Always look down and behind before and while
moving backwards.
• Never direct discharged material toward anyone.
Avoid discharging material against a wall or obstruc-
tion. Material may richochet back toward the operator.
Stop the blade when crossing gravel surfaces.
• Do not operate the mower without proper guards,
plates, grass catcher or other safety protective devices
in place.
• See manufacturer’s instructions for proper operation
and installation of accessories. Only use accessories
approved by the manufacturer.
• Stop the blade(s) when crossing gravel drives, walks,
or roads.
• Stop the engine (motor) whenever you leave the equip-
ment, before cleaning the mower or unclogging the
chute.
• Shut the engine (motor) off and wait until the blade comes
to complete stop before removing grass catch er.
• Mow only in daylight or good artifi cial light.
• Do not operate the machine while under the infl uence
of alcohol or drugs.
• Never operate machine in wet grass. Always be sure of
your footing: keep a fi rm hold on the handle and walk;
never run.
• Disengage the self-propelled mechanism or drive clutch
on mowers so equipped before starting the engine (motor).
• If the equipment should start to vibrate abnormally,
stop the engine (motor) and check immediately for the
cause. Vibration is generally a warning of trouble.
• Always wear safety goggles or safety glasses with side
shields when operating mower.
II. SLOPE OPERATION
Slopes are a major factor related to slip and fall accidents
which can result in severe injury. All slopes require extra
caution. If you feel uneasy on a slope, do not mow it.
DO:
• Mow across the face of slopes: never up and down. Exer-
cise extreme caution when changing direction on slopes.
• Remove obstacles such as rocks, tree limbs, etc.
• Watch for holes, ruts, or bumps. Tall grass can hide
obstacles.
DO NOT:
• Do not trim near drop-offs, ditches or embankments.
The operator could lose footing or balance.
• Do not trim excessively steep slopes.
• Do not mow on wet grass. Reduced footing could cause
slipping.
III. CHILDREN
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity.
Never
assume that
children will remain where you last saw them.
• Keep children out of the trimming area and under the
watchful care of another re spon si ble adult.
• Be alert and turn machine off if children enter the
area.
• Before and while walking backwards, look behind and
down
for small children.
• Never allow children to operate the machine.
• Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
IV. SAFE HANDLING OF GASOLINE
Use extreme care in handling gasoline. Gasoline is ex-
tremely fl ammable and the vapors are explosive.
• Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
• Use only an approved container.
• Never remove gas cap or add fuel with the engine run-
ning. Allow engine to cool before refueling.
3
SAFETY RULES .........................................................2-3
PRODUCT SPECIFICATIONS....................................... 3
CUSTOMER RESPONSIBILITIES................................. 3
ASSEMBLY.................................................................... 4
OPERATION ............................................................... 5-8
MAINTENANCE SCHEDULE ........................................ 9
MAINTENANCE ........................................................ 9-11
SERVICE AND AD JUST MENTS ................................. 12
STORAGE .................................................................... 13
TROU BLE SHOOT ING ................................................. 14
REPAIR PARTS....................................................... 16-19
WARRANTY................................................................. 20
PRODUCT SPECIFICATIONS
Gasoline Capacity 1.6 Quarts
and Type: (Unleaded Regular Only)
Oil Type (API SG–SL): SAE 30 (above 32°F);
SAE 5W-30 (below 32°F)
Oil Capacity: 20 Ounces
Spark Plug (Gap: .030"): Champion RC12YC
Blade Bolt Torque: 35-40 ft. lbs. (47-54 N-m)
CONGRATULATIONS on your purchase of a new lawn
mower. It has been designed, engineered and man u fac tured
to give you the best possible dependability and performance.
Should you experience any problem you cannot easily
remedy, please contact your nearest authorized service
center/department. We have competent, well-trained
tech ni cians and the proper tools to service or repair this
lawn mower.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your lawn mower
properly. Always observe the “SAFETY RULES”.
SERIAL
NUMBER: _________________________________
DATE OF PURCHASE: _______________________
THE MODEL AND SERIAL NUMBERS WILL BE FOUND
ON A DECAL ATTACHED TO THE REAR OF THE LAWN
MOWER HOUSING.
YOU SHOULD RECORD BOTH SERIAL NUMBER AND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
CUSTOMER RESPONSIBILITIES
• Read and observe the safety rules.
• Follow a regular schedule in maintaining, caring for and
using your lawn mower.
• Follow the instructions under “Maintenance” and “Stor-
age” sec tions of this own er’s manual.
TABLE OF CONTENTS
• Never refuel the machine indoors.
• Never store the machine or fuel container where there
is an open fl ame, spark or pilot light such as a water
heater or on other appliances.
• Never fi ll containers inside a vehicle, on a truck or trailer
bed with a plastic liner. Always place containers on
the ground away from your vehicle before fi lling.
• Remove gas-powered equipment from the truck or trailer
and refuel it on the ground. If this is not possible, then
refuel such equipment with a portable container, rather
than from a gasoline dispenser nozzle.
• Keep the nozzle in contact with the rim of the fuel tank
or container opening at all times until fueling is complete.
Do not use a nozzle lock-open device.
• If fuel is spilled on clothing, change clothing immedi-
ately.
• Never overfi ll fuel tank. Replace gas cap and tighten
securely.
V. GENERAL SERVICE
• Never run a machine inside a closed area.
• Never make adjustments or repairs with the engine
(motor) running. Disconnect spark plug wire, and keep
wire away from plug to prevent accidental starting.
• Keep nuts and bolts, especially blade attachement
bolts, tight and keep equipment in good condition.
• Never tamper with safety devices. Check their proper
operation regularly.
• Keep machine free of grass, leaves, or other debris
build-up. Clean oil or fuel spillage. Allow machine to
cool before storing.
• Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
• Never attempt to make wheel height adjustments while
the engine (motor) is running.
• Grass catcher components are subject to wear, dam-
age, and deterioration, which could expose moving
parts or allow objects to be thrown. Frequently check
com po nents and replace with manufacturer’s rec om -
mend ed parts, when necessary.
• Mower blade is sharp and can cut. Wrap the blade or
wear gloves, and use extra caution when servicing it.
• Do not change the engine governor setting or overspeed
the engine.
• Maintain or replace safety and instruction labels, as
necessary.
WARNING: This lawn mower is equipped with an internal com bus tion engine and should not be used on or near any
un im proved forest-covered, brush-covered or grass-cov ered land unless the engine’s exhaust system is equipped with
a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in
effective working order by the operator. A spark arrester for the muffl er is available through your nearest authorized
service centre.
4
ASSEMBLY
Read these instructions and this man u al in its entirety before
you attempt to assemble or operate your new lawn mow er.
IMPORTANT: THIS LAWN MOWER IS SHIPPED WITH-
OUT OIL OR GASOLINE IN THE ENGINE.
Your new lawn mower has been as sem bled at the factory
with the ex cep tion of those parts left unassembled for ship-
ping purposes. All parts such as nuts, washers, bolts, etc.,
necessary to com plete the as sem bly have been placed in
the parts bag. To ensure safe and proper operation of your
lawn mow er, all parts and hard ware you assemble must
be tightened se cure ly. Use the correct tools as nec es sary
to ensure proper tightness.
TO RE MOVE LAWN MOW ER FROM CAR TON
1. Remove loose parts included with mower.
2. Cut down two end corners of car ton and lay end panel
down fl at.
3. Remove all packing materials ex cept padding be tween
upper and lower handle and padding holding operator
presence control bar to up per handle.
4. Roll lawn mower out of carton and check carton thor-
ougly for ad di tion al loose parts.
HOW TO SET UP YOUR LAWN MOW ER
TO UNFOLD HANDLE (See Fig. 1)
IMPORTANT: UNFOLD HANDLE CAREFULLY SO AS
NOT TO PINCH OR DAMAGE CON TROL CABLES.
1. Raise handles until lower handle section locks into
place in mowing position.
2. Remove protective padding, raise upper handle sec-
tion into place on lower handle and tighten both handle
knobs.
3. Remove handle padding holding operator pres ence
control bar to upper handle.
Your handles may be adjusted for your mowing comfort.
Refer to “ADJUST HANDLE” in the Service and Ad just ments
sec tion of this man u al.
TO ASSEMBLE GRASS CATCHER
(See Fig. 2)
1. Put grass catcher frame into grass bag with rigid part
of bag on the bottom. Make sure the frame handle is
outside of the bag top.
2. Slip vinyl bindings over frame.
NOTE: If vinyl bindings are too stiff, hold them in warm water
for a few minutes. If bag gets wet, let it dry before using.
TO INSTALL ATTACHMENTS
Your lawn mower was shipped ready to be used as a
mulcher. To convert mower to bagging or discharging,
see “TO CON VERT MOWER” in the Operation section of
this man u al.
FIG. 1
OPERATOR
PRESENCE
CONTROL
BAR
HANDLE
KNOB
LIFT
UP
LIFT
UP
LOWER
HANDLE
MOWING
PO SI TION
UPPER
HANDLE
FIG. 2
FRAME
HANDLE
VINYL
BINDINGS
FRAME
OPENING
5
KNOW YOUR LAWN MOWER
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER.
Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments.
Save this manual for future reference.
MEETS CPSC SAFETY REQUIREMENTS
Our rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute
and the U.S. Consumer Product Safety Commission. The blade turns when the engine is running.
STARTER HANDLE – used for starting the engine.
PRIMER – pumps additional fuel from the carburetor to the
cylinder for use when starting a cold engine.
MULCHER DOOR – allows conversion to discharge or
bagging operation.
HOUSING
GRASS
CATCHER
OPERATOR PRESENCE CONTROL BAR – must be held
down to the handle to start the engine. Release to stop
the engine.
DRIVE CONTROL LEVER – used to engage power-pro-
pelled forward mo tion of lawn mower.
OPERATOR
PRESENCE
CON TROL
BAR
WHEEL
ADJUSTER
(ON EACH
WHEEL)
STARTER
HANDLE
EN GINE OIL CAP WITH DIPSTICK
HANDLE KNOB
GAS O LINE
FILL ER CAP
These symbols may appear on your lawn mower or in literature supplied with the product. Learn and understand
their meaning.
PRIMER
OPERATION
IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine.
MUFFLER
AIR FILTER
DRIVE CONTROL LEVER
DRIVE COVER
SPARK PLUG
MULCHER DOOR
6
SIDE DISCHARGING (See Fig. 6)
• Rear door must be closed.
• Open mulcher door and install dis charge defl ector
under door as shown.
• Mower is now ready for discharging operation.
• To convert to mulching or bagging operation, dis charge
defl ector must be removed and mulcher door must be
closed.
TO CONVERT MOWER
Your lawn mower was shipped ready to be used as a
mulcher. To convert to bagging or discharging:
REAR BAGGING (See Fig. 5)
• Lift rear door of the lawn mower and place the grass
catcher frame hooks onto the door pivot pins.
• To convert to mulching or dis charg ing operation, remove
grass catch er and close rear door.
FIG. 5
PIVOT PINS REAR
DOOR
GRASS
CATCHER
HANDLE
CATCH ER FRAME HOOK
HOW TO USE YOUR LAWN MOWER
ENGINE SPEED
The engine speed was set at the factory for optimum per-
formance. Speed is not adjustable.
ENGINE ZONE CONTROL
CAUTION: Federal regulations require
an engine control to be installed on this
lawn mower in order to minimize the risk
of blade contact injury. Do not un der
any cir cum stanc es attempt to defeat
the function of the operator control.
The blade turns when the engine is
running.
• Your lawn mower is equipped with an operator presence
control bar which requires the operator to be positioned
behind the lawn mower handle to start and operate the
lawn mower.
DRIVE CONTROL (See Fig. 3)
• Self-propelling is controlled by hold ing the operator
presence control bar down to the handle and push-
ing the drive control lever forward until it clicks; then
releasing the lever.
• Forward motion will stop when the operator presence
control bar is re leased. To stop forward motion without
stop ping engine, re lease the operator presence con-
trol bar slight ly until the drive control dis en gag es. Hold
op er a tor presence control bar down against handle to
con tin ue mowing without self-pro pel ling.
• To keep drive control engaged when turning corners,
push down on han dle and lift front wheels off ground
while turning lawn mower.
The operation of any lawn mower can result in foreign objects thrown into the eyes, which can result in
severe eye damage. Always wear safety glasses or eye shields while operating your lawn mower or per-
forming any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask
over spectacles.
OPERATION
FIG. 4
LEVER BACKWARD TO LOWER MOWER
LEVER FORWARD TO RAISE MOWER
PLATE
TAB
LEVER
TO ENGAGE
DRIVE CONTROL
DRIVE
CONTROL
DRIVE
CONTROL
DISENGAGED
OPERATOR PRESENCE CONTROL BAR
FIG. 3
TO ADJUST CUTTING HEIGHT (See Fig. 4)
Raise wheels for low cut and lower wheels for high cut,
adjust cutting height to suit your requirements. Me di um
position is best for most lawns.
• To change cutting height, squeeze adjuster lever to ward
wheel. Move wheel up or down to suit your re quire ments.
Be sure all wheels are in the same setting.
NOTE: Adjuster is properly positioned when plate tab inserts
into hole in lever. Also, 9-position adjusters (if so equipped)
allow lever to be positioned between the plate tabs.
Loading...