Husqvarna 917374443 Owner’s Manual

Owner's Manual

Husqvarna

ROTARY LAWN MOWER

650 Series Briggs & Stratton Engine

Power-Propelled Electric Start

22" Multi-Cut

Model No.

917.374443

• EspaSol, p. 19

CAUTION:

Read and follow all

Safety Rules and Instructions before operating this equipment

Husqvarna, Charlotte, NC 28269

Visit our website: www.husqvama.com

U.S.A.

Warranty ................................................... 2

Safety Rules .......................................... 2-3

Product Specifications .............................. 5

Assembly / Pre-Operation ..................... 6-7

Operation ............................................. 8-11

Maintenance Schedule ........................... 12

IMPORTANT: This cutting machine is capable of amputating hands and feet and throwing ob-

jects. Failure to observe the following safety instructions could result in serious injury or death.

_i,Look for this symbol to point out im-

portant safety precautions. It means CAUTIONN! BECOME ALERTH!

YOUR SAFETY IS INVOLVED. AWARNING: In order to prevent accidental

starting when setting up, transporting, ad- justing or making repairs, always disconnect spark plug wire and place wire where it cannot

come in contact with plug.

AWARNING: Engine exhaust, some of its

constituents, and certain vehicle compo- nents contain or emit chemicals known to

the State of California to cause cancer and

birth defects or other reproductive harm.

_I,WARNING: Battery posts, terminals and

related accessories contain lead and lead compounds, chemicals known to the State

of California to cause cancer and birth defects or other reproductive harm. Wash

hands after handling.

CAUTION: Muffler and other engine

parts become extremel_ hot during operation and

remain hot after engi has stopped. To avoid severe burns on contact, stay away

from these areas.

I. GENERAL OPERATION

• Read, understand, and follow all instructions on the machine and in the

manual(s) before starting. Be thoroughly

familiar with the controls and the proper

use of the machine before starting.

• Do not put hands or feet near or under rotating parts. Keep clear of the dis- charge opening at all times.

• Only allow responsible individuals, who are familiar with the instructions, to

operate the machine.

• Clear the area of objects such as rocks, toys, wire, bones, sticks, etc., which could be picked up and thrown by blade.

• Be sure the area is clear of other people before mowing. Stop the machine if anyone enters the area.

Maintenance ...................................... 12-15

Service and Adjustments ................... 15-16

Storage .............................................. 16-17

Troubleshooting ................................. 17-18

Repair Parts ....................................... 38-47

• Do not operate the mower when bare- foot or wearing open sandals. Always

wear substantial foot wear.

• Do not pull mower backwards unless abso- lutely necessary. Always Iookdown and be- hind before and while moving backwards.

• Never direct discharged material toward anyone. Avoid discharging material againstawall or obstruction. Material may richochet back toward the operator. Stop the blade when crossing gravel surfaces.

• Do not operate the mower without prop- er guards, plates, grass catcher or other safety protective devices in place.

• See manufacturer's instructions for proper operation and installation of

accessories. Only use accessories ap- proved by the manufacturer.

• Stop the blade(s) when crossing gravel drives, walks, or roads.

• Stop the engine (motor) whenever you leave the equipment, before cleaning the mower or unclogging the chute.

• Shut the engine (motor) off and wait until the blade comes to complete stop before removing grass catcher.

• Mowonly in daylight orgood artificial light.

• Do not operate the machine while under the influence of alcohol or drugs.

• Never operate machine in wet grass. Always be sure of your footing: keep a

firm hold on the handle; walk, never run.

• Disengage the self-propelled mech- anism or drive clutch on mowers so

equipped before starting the engine.

• If the equipment should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibra- tion is generally a warning of trouble.

• Always wearsafety goggles or safetyglass- es with side shields when operating mower.

II. SLOPE OPERATION

Slopes are a major factor related to slip & fall accidents which can result in severe

injury. All slopes require extra caution. If

2 you feel uneasy on a slope, do not mow it.

DO:

• Mowacrossthefaceofslopes:never up anddown.Exerciseextremecaution

whenchangingdirectionon slopes.

• Removeobstaclessuchas rocks,tree limbs,etc.

• Watchfor holes,ruts,or bumps.Tall grasscanhideobstacles.

DONOT:

• Donot trimneardrop-offs,ditchesor embankments.Theoperatorcouldlose

footingor balance.

• Donot trimexcessivelysteepslopes.

• Donot mowonwet grass.Reduced

footingcouldcauseslipping.

III. CHILDREN

Tragicaccidentscanoccuriftheoperatoris

notalerttothepresenceofchildren.Children areoftenattractedto the machineandthe

mowingactivity.Never assume that children

will remain where you last saw them.

• Keep children out of the trimming area and under the watchful care of another

responsible adult.

• Be alert and turn machine off if children enter the area.

• Before and while walking backwards, look behind and down for small children.

• Never allow children to operate machine.

• Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.

IV. SAFE HANDLING OF GASOLINE Use extreme care in handling gasoline.

Gasoline is extremely flammable and the

vapors are explosive.

• Extinguish all cigarettes, cigars, pipes and other sources of ignition.

• Use only an approved container.

• Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling.

• Never refuel the machine indoors.

• Never store the machine or fuel contain- er where there is an open flame, spark

or pilot light such as a water heater or on other appliances.

• Never fill containers inside a vehicle, on

a truck or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before filling.

• Remove gas-powered equipment from the truck or trailer and refuel it on the

ground. If this is not possible, then refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do

not use a nozzle lock-open device.

• If fuel is spilled on clothing, change clothing immediately.

• Never overfill fuel tank. Replace gas cap and tighten securely.

V. GENERAL SERVICE

• Never run machine inside a closed area.

• Never make adjustments or repairs with the engine (motor) running. Disconnect the

spark plug wire, and keep the wire away from the plug to prevent accidental starting.

• Keep nuts and bolts, especially blade attachment bolts, tight and keep equip- ment in good condition.

• Never tamper with safety devices. Check their proper operation regularly.

• Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spill-

age. Allow machine to coot before storing.

• Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.

• Never attempt to make wheel height adjustments while the engine is running.

• Grass catcher components are subject to wear, damage, and deterioration, which

could expose moving parts or allow objects to be thrown. Frequently check compo- nents and replace with manufacturer's recommended parts, when necessary.

• Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra caution when servicing them.

• Do not change the engine governor set- ting or overspeed the engine.

• Maintain or replace safety and instruc- tion labels, as necessary.

&WARNING: This lawn mower is equipped with an internal combustion engine and

should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the state of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal

lands. A spark arrester for the muffler is available through your nearest Husqvarna or other authorized service center (See the REPAIR PARTS section of this manual).

SECTION 1: LIMITED WARRANTY

Husqvarna Forest & Garden Company ("Husqvarna")

warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship

from the date of purchase for the "Warranty Period" of the product as set forth below:

2 YEAR NON-COMMERCIAL WARRANTY: Auto-

matic Mower, Riding lawn mowers, yard and garden tractors, walk behind mowers, tillers, chain saws, trimmers, brushcutters, clearing saws, snow blowers,

handheld blowers, backpack blowers, hedge trimmers, electrical products and power-assist collection systems

for noncommercial, nonorofessional noninstitutional or

nonincome producinq use, except as herein stated.

Emission control system components necessary to comply with CARB-TIER-II and EPA regulations.

Husqvarna Safety Apparel carries a 90-day warranty from the date of the customer's original purchase for defects in material and workmanship. Normal wear, tear or abuse is not covered under warranty. Product

must be returned to Charlotte with a warranty claim form. All care and maintenance instructions must be

followed as stated by the manufacturer on the care

label. The fit of the protective apparel/boot is not covered under warranty.

SECTION 2: HUSQVARNA'S OBLIGATIONS UNDER THE WARRANTY

Husqvarna will repair or replace defective components without charge for parts or labor if a component fails

because of a defect in material or workmanship during the warranty period.

SECTION 3: ITEMS NOT COVERED BY THIS WAR-

RANTY The following items are not covered by this warranty:

(1)Normal customer maintenance items which become

worn through normal regular use, including, but not limited to, belts, blades, blade adapters, bulbs, filters, guide bars, lubricants, rewind springs, saw chain, spark plugs, starter ropes and tines;

(2) Natural discoloration of material due to ultraviolet

light;

(3)Lawn and garden attachments are covered by a

third party which gives a warranty, all claims for warranty should be sent to the manufacturer; and

(4)Emission Control System components necessary

to which are manufactured by third party engine manufacturer.

SECTION 4: EXCEPTIONS AND LIMITATIONS This warranty shall be inapplicable to defects resulting

from the following:

(1)Accident, abuse, misuse, negligence and neglect,

including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any adverse reaction due to incorrect

storage or use habits;

(2)Failure to operate or maintain the unit in accor-

dance with the Owner's/Operator's manual or instruction sheet furnished by Husqvarna;

(3)Alterations or modifications that change the

intended use of the product or affects the product's performance, operation, safety, or durability, or

causes the product to fail to comply with any ap- plicable laws; or:

(4)Additional damage to parts or components due to

continued use occurring after any of the above.

REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUEN- TIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT TO THE EXTENT PROHIBITED BY AP- PLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICU- LAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO THE WARRANTY PERIOD AS DEFINED IN THE LIMITED WARRANTY STATE- MENT. HUSQVARNA RESERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE

PRODUCT WITHOUT NOTICE, AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY

MANUFACTURED PRODUCTS. Some states do not allow the exclusion of incidental

or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations or

exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

SECTION 5: CUSTOMER RESPONSIBILITIES The product must exhibit reasonable care, mainte-

nance, operation, storage and general upkeep as written in the maintenance section of the Owner's/

Operator's manual. Should an operational problem or failure occur, the product should not be used, but delivered as is to an authorized Husqvarna dealer for evaluation. Proof of purchase, as explained in section 6, rests solely with the customer.

SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION

It is the Owner's and Dealer's responsibility to make certain that the Warranty Registration Card is properly filled out and mailed to Husqvarna Forest & Garden

Company. This card should be mailed within ten (10) days from the date of purchase in order to confirm the

warranty and to facilitate post-sale service. Proof of purchase must be presented to the authorized

Husqvarna dealer in order to obtain warranty service. This proof must include date purchased, model num- ber, serial number, and complete name and address of the selling dealer.

To obtain the benefit of this warranty, the product believed to be defective must be delivered to an

authorized Husqvarna dealer in a timely manner, no later than thirty (30) days from date of the operational

problem or failure. The product must be delivered at the owner's expense. Pick-up and delivery charges are

not covered by this warranty. An authorized Husqvarna dealer can be normally located through the "Yellow

Pages" of the local telephone directory or by calling 1-800-HUSKY62 for a dealer in your area.

HUSQVARNA

7349 Statesville Road

Charlotte, NC 28269

531 83 81-23 2002

Serial Number: Date of Purchase:

Gasoline Capacity / Type: 1.6 Quarts (Unleaded Regular) Oil Type (API SG-SL): SAE 30 (above 32°F); SAE 5W-30 (below 32°F) Oil Capacity: 20 Ounces Spark Plug (Gap: .030") Champion RJ 19LM or J19LM Blade Bolt Torque: 35-40 ft. Ibs.

• The model and serial numbers will be found on a decal on the rear of the lawn mower housing. Record both serial number and date of purchase in space provided above.

These accessories were available when this lawn mower was produced. They are not shipped with your mower. They are also available at most Sears retail outlets and service centers. Some of these accessories may not apply to your lawn mower.

LAWN MOWER PERFORMANCE

CLIPPING

DEFLECTORS

FOR

REAR DISCHARGE

LAWN MOWERS

STABILIZER

GRASS CATCHERS

FOR

REAR DISCHARGE

LAWN MOWERS

LAWN MOWER MAINTENANCE

MUFFLERS

BELTS BLADES BLADE ADAPTERS

AIR FILTERS

GRASS CATCHERS

SIDE DISCHARGE

LAWN MOWERS

WHEELS

FOR

SPARK PLUGS

ENGINE OIL

Read these instructions and this manual in its entirety before you attempt to assemble

or operate your new lawn mower.

IMPORTANT: This lawn mower is shipped

WITHOUT OIL OR GASOLINE in the engine.

Your new lawn mower has been assem-

bled at the factory with the exception of

those parts left unassembled for shipping

purposes. To ensure safe and proper operation of your lawn mower, all parts and hardware you assemble must be tight- ened securely. Use the correct tools as

necessary to ensure proper tightness. All

parts such as nuts, washers, bolts, etc.,

necessary to complete the assembly have

been placed in the parts bag. TO REMOVE MOWER FROM

CARTON

1. Remove loose parts included with mower.

2. Cut down two end corners of carton and lay end panel down flat.

3. Remove all packing materials except padding between upper and lower handle and padding holding operator presence control bar to upper handle.

4. Roll lawn mower out of carton and check carton thoroughly for additional

loose parts.

HOW TO SET UP YOUR MOWER

TO UNFOLD HANDLE IMPORTANT: Unfold handle carefully so

as not to pinch or damage control cables.

1. Raise handles until lower handle sec- tion locks into place in mowing posi-

tion.

2. Remove protective padding, raise up- per handle section into place on lower handle and tighten both handle knobs.

3. Remove handle padding holding operator presence control bar to upper

handle.

Your lawn mower handle can be adjusted

for your mowing comfort. Refer to "AD-

JUST HANDLE" in the Service and Adjust- ments section of this manual.

Operator MOWING I POSITION

control bar

/ //

/ /

UP handle

Upper

Handle

knob

Lower handle

TO ASSEMBLE GRASS CATCHER

1. Put grass catcher frame into grass bag with rigid part of bag on the bottom.

Make sure the frame handle is outside

of the bag top.

2. Slip vinyl bindings over frame. NOTE: If vinyl bindings are too stiff, hold

them in warm water for a few minutes. If

bag gets wet, let it dry before using.

Vinyl Frame

bindings opening

TO PREPARE BATTERY NOTE: Your battery must be charged

before you can start your lawn mower.

1. Connect battery charger connector (male) to harness connector (female).

2. Plug battery charger into 110 volt A.C. outlet.

3. Leave battery charger connected for 24 hours before starting your engine

for the first time.

4. After charging, disconnect harness connector (female) from battery char- ger connector (male).

Connect your battery charger to charge battery after each use. IMPORTANT: The engine will not re- charge your battery.

At the end of the mowing season the

battery should be charged for 48 hours to

,_otect the battery during winter storage.

CAUTION: Always disconnect the engine connector (male) from the battery connector (female) to prevent accidental starting when transporting or storing your

lawn mower after the season.

Engine Harness

connector connector

ale)

Charger

connector (male)

TO INSTALL ATTACHMENTS Your lawn mower was shipped ready to be

used as a mulcher. To convert mower to bagging or discharging, see "TO CON-

VERT MOWER" in the Operation section of this manual.

KNOW YOUR LAWN MOWER

READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING

YOUR LAWN MOWER. Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments. Save this manual for

future reference.

These symbols may appear on your lawn mower or in literature supplied with the

product. Learn and understand their meaning.

CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER, KEEP HANDS

OR WARNING ON OFF AND FEET AWAY

Drive control bar

Key

start switch

Auxiliary starter

handle

- Operator presence control bar

Handle knob

Engine oil cap with dipstick

Grass Primer

catcher

Gasoline

Muffler

filler cap_

plug

Housing

Air

Mulcher dool

IMPORTANT: This lawn mower is shipped

WITHOUT OIL OR GASOLINE in the engine.

Drive cover

Wheel adjuster (on each wheel)

MEETS CPSC SAFETY REQUIREMENTS Sears rotary walk-behind power lawn mowers conform to the safety standards of the

American National Standards Institute and the U.S. Consumer Product Safety Com-

mission. The blade turns when the engine is running. Operator presence control bar - must

be held down to the handle to start the

engine. Release to stop the engine.

Primer- pumps additional fuel from the carburetor to the cylinder for use when

starting a cold engine.

Auxiliary starter handle - used for start- ing engine.

Mulcher door - allows conversion to discharging or bagging operation.

Drive control bar - used to engage power-propelled forward motion of mower.

Key start switch - used for starting engine. 8

The operationof any lawn

SAFETYGLASSESmowercan resultin foreign

objectsthrownintotheeyes,

which can result in severe

eye damage. Atways wear safety glasses or eye shields while oper- ating your lawn moweror performingany

adjustmentsor repairs.We recommenda

standardsafetyglassesorwidevisionsafety

maskwornoverspectacles.

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED Engine speed was set at the factory for

optimum performance. It is not adjustable.

ENGINE ZONE CONTROL

ACAUTION: Federal regulations require

an engine control to be installed on this lawn mower in order to minimize the

risk of blade contact injury. Do not under

any circumstances attempt to defeat the function of the operator control. The blade turns when the engine is running.

• Your lawn mower is equipped with an operator presence control bar which requires the operator to be positioned

behind the lawn mower handle to start and operate the lawn mower.

TO OPERATE DRIVE SYSTEM

• To start forward motion, lift drive con-

trol bar up to handle.

• To stop forward motion, release drive

control bar.

IMPORTANT: Always keep drive control

fully engaged against handle when in use.

• To change cutting height, squeeze ad- juster lever toward wheel. Move wheel

up or down to suit your requirements. Be sure all wheels are in the same setting.

NOTE: Adjuster is properly positioned when plate tab inserts into hole in lever. Also, 9-position adjusters (if so equipped) allow lever to be positioned between the plate tabs.

LEVER BACKWARD Plate tab TO LOWER MOWER

LEVER FORWARD TO RAISE MOWER Lever TO CONVERT MOWER Your lawn mower was shipped ready to be

used as a mulcher. To convert to bagging or discharging:

REAR BAGGING

• Open reardoorand remove mulcherplug. Store mulcher plug in a safe place.

• You can now install the grass catcher or

optional clipping deflector.

• To convert to mulching or discharging

operation, install mulcher plug into rear discharge opening of mower.

Mulcher

plug

SIDE DISCHARGING

Operator presence

control bar

DRIVE CONTROLENGAGED

• Mulcher plug must be installed into rear

discharge opening of mower.

• Open mulcher door and install dis- charge deflector under door as shown.

• Mower is now ready for discharging

operation.

• To convert to mulching or bagging

operation, discharge deflector must be

removed and mulcher door closed.

t \ /

DRIVE CONTROL DISENGAGED

TO ADJUST CUTTING HEIGHT

Raise wheels for low cut and lower wheels

for high cut, adjust cutting height to suit mulche_ your requirements. Medium position is door

best for most lawns. 9

Open

Dischargedeflector

SIMPLE STEPS

TO REMEMBER WHEN CONVERTING YOUR MOWER

FOR MULCHING -

1. Rear mulcher plug installed.

2. Mulcher door closed. FOR REAR BAGGING -

1. Rear mulcher plug removed.

2. Grass catcher installed.

3. Mulcher door closed. FOR SIDE DISCHARGING -

1. Rear mulcher plug installed.

2. Discharge deflector installed.

ACAUTION: Do not run your lawn

mower without mulcher plug or approved

grass catcher in place. Never attempt to operate the lawn mower with the rear door

removed or propped open.

TO EMPTY GRASS CATCHER

1. Lift up on grass catcher using the

frame handle.

2. Remove grass catcher with clippings

from under lawn mower handle.

3. Empty clippings from bag. NOTE: Do not drag the bag when empty- ing; it will cause unnecessary wear.

i/ Grass

catcher

- frame

_. _ _ handle

BEFORE STARTING ENGINE

ADD OIL

Your lawnmower is shipped without oil in the engine. For type and grade of oil to

use, see "ENGINE" in the Maintenance section of this manual.

• I, CAUTION: DO NOT overfill engine with oil, or it will smoke heavily from the muffler on startup.

1. Be sure lawnmower is level.

2. Remove oil dipstick from oil fill spout.

3. You receive a container of oil with the

unit. Slowly pour the entire container

down the oil fill spout into the engine. NOTE: Initial oil fill requires only 18 oz. due to residual oil in engine from the manufacturers 100% quality testing. When changing oil you may need 20 oz.

4. Insert and tighten dipstick. IMPORTANT:

• Check oil level before each use. Add oil

if needed. Fill to full line on dipstick.

• Change the oil after every 25 hours of

operation or each season. You may

need to change the oil more often under dusty, dirty conditions. See "TO

CHANGE ENGINE OIL" in the Mainte- nance section of this manual.

gine

oil cap

Gasoline filler cap

Primer

ADD GASOLINE

• Fill fuel tank to bottom of tank filler neck.

Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87

octane. Do not mix oil with gasoline. Pur-

chase fuel in quantities that can be used

within 30 days to assure fuel freshness. A CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline

near an open flame.

A_, CAUTION: Alcohol blended fuels

(called gasohol or using ethanol or metha- nol) can attract moisture which leads to separation and formation of acids during

storage. Acidic gas can damage the fuel system of an engine while in storage. To

avoidengineproblems,thefuel system shouldbeemptiedbeforestorageof 30 daysor longer. Emptythegas tank,start theengineand letit run untilthefuel lines

andcarburetorareempty. Usefreshfuel nextseason. SeeStorageInstructionsfor

additionalinformation.Neveruseengine or carburetorcleanerproductsinthe fuel tankorpermanentdamagemayoccur.

TO STOP ENGINE

• To stop engine, release operator pres- ence control bar.

TO START ENGINE

NOTE: Due to protective coatings on the

engine, a small amount of smoke may be

present during the initial use of the product and should be considered normal.

1. To start a cold engine, push primer three (3) times before trying to start. Use a firm push. This step is not usu- ally necessary when starting an engine

which has already run for a few minutes.

2. Hold operator presence control bar down to the handle and turn the start key.

IMPORTANT: Do not crank engine more

than five continous seconds between each time you try to start. Wait 5 to 10 seconds

between each attempt.

• To start engine using the rope starter, follow the steps above. Exchange the

use of the starter rope for start key. Pull starter handle quickly. Do not allow

starter rope to snap back.

NOTE: In coolerweather it may be necessary to repeat priming steps. In warmer weather over priming may cause flooding and engine will not start. If you do flood engine wait a few minutes before attempting to start and do not repeat priming steps.

MOWING TIPS =_,CAUTION: Do not use de-thatcher

blade attachments on your mower. Such

attachments are hazardous, will damage your mower and could void your warranty.

• Under certain conditions, such as very tall grass, it may be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of grass clippings.

It may also be necessary to reduce

ground speed and/or run the lawn mower over the area a second time.

• For extremely heavy cutting, reduce the

width of cut by overlapping previously

cut path and mow slowly.

• For better grass bagging and most cut- ting conditions, the engine speed should be set in the FAST position.

• Pores in cloth grass catchers can become filled with dirt and dust with use

and catchers will collect less grass. To prevent this, regularly hose catcher off

with water and let dry before using.

• Keep top of engine around starter clear and clean of grass clippings and chaff.

This will help engine air flow and extend engine life.

MULCHING MOWING TIPS IMPORTANT: For best performance,

keep mower housing free of built-up grass and trash. See "CLEANING" in the

Maintenance section of this manual.

• The special mulching blade will recut

the grass clippings many times and

reduce them in size so that as they fall

onto the lawn they will disperse into the grass and not be noticed. Also, the

mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade)

speed as this will provide the best recut- ting action of the blades.

• Avoid cutting your lawn when it is wet.

Wet grass tends to form clumps and

interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has

dried, yet the newly cut area will not be exposed to direct sunlight.

• For best results, adjust the lawn mower cutting height so that the lawn mower

cuts off only the top one-third of the

grass blades. If the lawn is overgrown

it will be necessary to raise the height of cut to reduce pushing effort and to keep

from overloading the engine and leaving

clumps of mulched grass. For extremely heavy grass, reduce your width of cut

by overlapping previously cut path and mow slowly.

MAX 1/3

• Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a sec-

ond cut, mow across (perpendicular) to the first cut path.

• Change your cutting pattern from week

to week. Mow north to south one week then change to east to west the next

week. This will help prevent matting

11 and graining of the lawn.

SCHEDULE

Check for Loose Fasteners

L Clean / Inspect Grass Catcher *

_ Check Tires

N Check Drive Wheels ***

Clean Lawn Mower ....

M Clean under Drive Cover ***

O Check Drive Belt / Pulleys ***

_ heck / Sharpen / Replace Blade

Lubrication

Clean and Recharge Battery ** Check Engine Oil level

_' Change Engine Oil N Clean Air Filter

_ Inspect Muffler

N Replace Spark Plug E Replace Air Filter Paper Cartridge

Empty fuel system or add Stabilizer

* (if so equipped)

** Electric-Start mowers

*** Power-Propelled mowers

**** Use a scraper

to clean under deck

1 - Change more often if operating under a heavy load or in high outdoor temperatures. 2 - Service more often if operating in dirty or dusty conditions. 3 - Replace blades more often when mowing in sandy soil, 4 - Charge 48 hours at end of season.

5 - And after each 5 hours of use.

BEFORE AFTER EVERY EVERY EVERY

EACH EACH 10 25HOURS 100 BEFORE

USE USE HOURS OR SEASON HOURS STORAGE

I/3

GENERAL RECOMMENDATIONS

The warranty on this lawn mower does not

cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must

maintain unit as instructed in this manual.

Some adjustments will need to be made

periodically to properly maintain your unit. At least once a season, check to see if you should make any of the adjustments described in the Service and Adjustments

section of this manual.

• At least once a year, replace the spark plug, clean or replace air filter element and check blade for wear. A new spark

plug and clean/new air filter element assure proper air-fuel mixture and help your engine run better and last longer.

• Follow the maintenance schedule in this manual.

BEFORE EACH USE

• Check engine oil level.

• Check for loose fasteners.

LU BRICATION

Keep unit well lubricated (See "LUBRICATION CHART").

LUBRICATION CHART

Wheel

adjuster (on

each wheel)

@ Engine oil

Mulcher

door hinge

Rear door

hinge

Handle bracket mounting pins

_ Spray lubricant

See "ENGINE" in Maintenance section.

IMPORTANT: Do not oil or grease plastic

wheel bearings. Viscous lubricants will

attract dust and dirt that will shorten the life of the self-lubricating bearings. If you feel they

must be lubricated, use only a dry, powdered

2graphite type lubricant sparingly.

LAWN MOWER

Alwaysobservesafetyruleswhenper- forminganymaintenance. TIRES

• Keeptiresfree of gasoline,oil, or insect controlchemicalswhichcanharmrubber.

• Avoidstumps,stones,deepruts,sharp objectsandother hazardsthatmay

causetiredamage.

DRIVEWHEELS Checkfrontdrivewheelseachtimebefore

you mowtobe suretheymovefreely. Thewheelsnot turningfreelymeanstrash, grasscuttings,etc.areinthedrivewheelarea

and mustbe cleanedtofreedrivewheels.

Ifnecessaryto cleanthedrivewheels,be

sureto cleanbothfrontwheels.

1. Removehubcaps,Iocknuts&washers.

2. Removewheelsfrom wheeladjusters.

3. Removeanytrash or grasscuttings

frominsidethe dust cover,pinionand/ ordrivewheelgearteeth.

4. Putwheelsbackin place. NOTE: Ifaftercleaning,thedrivewheels

do notturnfreely,contacta Searsor other qualifiedservicecenter.

BLADE CARE Forbestresults,blademustbe keptsharp.

Replaceabentordamagedblade.

A CAUTION:Useonlyareplacementblade

approvedbythemanufacturerofyourmower. Usinga bladenot approvedby the manu-

facturerofyour mowerishazardous,could damageyourmowerandvoidyourwarranty.

TOREMOVEBLADE

1. Disconnectsparkplugwirefromspark

plugandplacewirewhere itcannot come incontactwith plug.

2. Turnlawnmoweron itsside.Make

sure airfilter andcarburetorareup.

3. Useawoodblockbetweenbladeand

mowerhousingtopreventbladefrom

turningwhen removingbladebolt. NOTE: Protectyour handswithgloves and/orwrapbladewith heavycloth.

4. Removeblade boltbyturningcounter- clockwise.

5. Removeblade& attachinghardware (bolt,lockwasher& hardenedwasher).

TOREPLACEBLADE

1. Positionbladeon thebladeadapter aligningthe two (2) holesinthe blade •

withthe raisedlugsonthe adapter.

2. Besurethetrailingedgeofblade(oppo- sitesharpedge)isuptowardtheengine.

3. Installthebladeboltwith the lock washerandhardenedwasherinto

bladeadapterandcrankshaft.

4. Useblockofwood betweenbladeand lawnmowerhousingandtightenthe

bladebolt,turningclockwise.

Recommendedtighteningtorque:35-40ft.lbs. IMPORTANT:Bladeboltis heattreated.

Ifboltneedsreplacing,replaceonlywith

approvedboltshownin the RepairParts sectionofthis manual.

Bladeadapter Key Crankshaft Lockwasher / /

bolt Hardened

washer Trailing edge Crankshaft TO SHARPEN BLADE NOTE: We do not recommend sharpening

the blade - but if you do, be sure the blade is balanced. Care should be taken to keep

the blade balanced. An unbalanced bladewill cause eventual damage to mower or engine.

• The blade can be sharpened with a file

or on a grinding wheel. Do not attempt to sharpen while on the mower.

• To check blade balance, drive a nail into

a beam or wall. Leave about one inch of

the straight nail exposed. Place center

hole of blade over the head of the nail. If blade is balanced, it should remain in

a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

GRASS CATCHER

• The grass catcher may be hosed with

water, but must be dry when used.

• Check your grass catcher often for dam-

age or deterioration. Through normal use it will wear. If catcher needs replac-

ing, replace only with approved replace- ment catcher shown in the Repair Parts

section of this manual. Give the lawn

mower model number when ordering.

GEAR CASE

• To keep your drive system working

properly, the gear case and area around the drive should be kept clean and free of trash build-up. Clean under the drive

cover twice a season. The gear case is filled with lubricant to the

proper level at the factory. The only time the lubricant needs attention is if service

has been performed on the gear case.

If lubricant is required, use only Texaco

Starplex Premium 1 Grease, Part No.

750369. Do not substitute.

ENGINE

LU BRICATION

Use only high quality detergent oil rated with

API service classification SG-SL Select the oil's SAE viscosity grade according to your

expected operating temperature.

SAE VISCOSITY GRADES

F -20 0 30 32 40 60 80 100

TEMPERATURE RANGE ANTiCiPATED BEFORE NEXT OiL CHANGE

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)improve starting in

cold weather, these multi-viscosity oils will result in increased oil consumption when

used above 32°F. Check your engine oil level more frequently to avoid possible

engine damage from running low on oil.

Change the oil after every 25 hours of op-

eration orat least once a year if the mower

is not used for 25 hours in one year. Check the crankcase oil level before

starting the engine and after each five (5)

hours of continuous use. Tighten oil plug

securely each time you check the oil level. TO CHANGE ENGINE OIL

NOTE: Before tipping lawn mower to drain oil, empty fuel tank by running engine until fuel tank is empty.

1. Disconnect spark plug wire from spark plug and place wire where it cannot

come in contact with plug.

2. Remove engine oil cap; lay aside on a clean surface.

3. Tip lawn mower on its side as shown and drain oil into a suitable container.

Rock lawn mower back and forth to re-

move any oil trapped inside of engine.

4. Wipe off any spilled oil from lawn mower or side of engine.

5. Slowly pour oil down the oil fill spout, stopping every few ounces to check the oil level with the dipstick.

6. Stop adding oil when you reach the FULL mark on the dipstick. Wait a

minute to allow oil to settle.

7. Continue adding small amounts of oil, rechecking the dipstick until oil level

settles at FULL. DO NOT overfill, or

engine will smoke heavily from the muffler on startup.

8. Always be sure to retighten oil dipstick before starting engine.

9. Reconnect spark plug wire to spark plug.

AIR FILTER Your engine will not run properly and

may be damaged by using a dirty air filter. Replace the air filter cartridge every

100 hours of operation or every season,

whichever occurs first. Service air cleaner more often under dusty conditions.

TO CLEAN AIR FILTER

1. Loosen screw and tilt cover to remove.

2. Carefully remove cartridge.

3. Clean by gently tapping on a flat sur- face. If very dirty, replace cartridge.

AI:;I,CAUTION: Petroleum solvents, such as kerosene, are not to be used to clean

cartridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do

not use pressurized air to clean or dry cartridge.

4. Install cartridge, then replace cover making sure the tabs are aligned with the slots in the back plate. Fasten screw securely.

.Lip Back plate

Cartridge _ / ,

___r _ Slot

MUFFLER

Inspect and replace corroded muffler as it

could create a fire hazard and/or damage. SPARK PLUG

Replace spark plug at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting

are shown in the "PRODUCT SPECIFIC- ATIONS" section of this manual.

CLEANING

IMPORTANT: For best performance,

keep mower housing free of built-grass and trash. Clean the underside of your

mower after each use.

Cover

tab

ACAUTION: Disconnectsparkplugwire fromsparkplugandplacewirewhereit

cannotcomein contactwithplug.

• Cleantheundersideof yourlawnmower byscrapingto removebuild-upofgrass

andtrash.

• Cleanengineoftento keeptrashfrom accumulating.A cloggedengineruns hotterandshortensenginelife.

• Keepfinishedsurfacesandwheelsfree ofallgasoline,oil,etc.

• Wedo not recommendusinga garden hoseto cleanlawnmowerunlessthe

electricalsystem,muffler,airfilterand

carburetorare coveredto keepwater

out. Waterinenginecan resultin short- enedenginelife.

CLEANUNDERDRIVECOVER Cleanunderdrivecoveratleasttwiceasea-

son. Scrapeundersideof cover with putty knifeorsimilartoolto removeany build-up oftrashorgrassonundersideofdrivecover.

_, WARNING: Toavoidseriousinjury,

beforeperforminganyserviceand adjustments:

1. Releasecontrolbarandstopengine.

2. Makesurethe bladeandall moving partshavecompletelystopped.

3. Disconnectsparkplugwirefromspark plugandplacewirewhere itcannot come incontactwith plug.

LAWN MOWER

TO ADJUST CUTTING HEIGHT

See "TO ADJUST CUTTING HEIGHT" in

the Operation section of this manual.

REAR DEFLECTOR

The rear deflector, attached between the

rear wheels of your mower, is provided to minimize the possibility that objects will

be thrown out of the rear of the mower into the operator mowing position. If the

deflector becomes damaged, it should be

replaced.

TO REMOVE DRIVE BELT

1. Remove drive cover.

2. Remove belt from gearcase pulley by pushing down on arm and rolling belt off pulley.

3. Turn lawn mower on its side with air filter and carburetor down.

4. Remove blade, engine pulley and debris shield.

5. Remove engine pulley and belt from debris shield.

PUSH DOWN -..

Drive cover

Pulley

Engine pulley

Drive belt

Belt retainer

Debris shield

TO REPLACE DRIVE BELT

1. Place new drive belt in engine pulley and belt retainer of debris shield.

2. Route the other end of the new drive belt through hole in housing.

3. Reinstall debris shield.

4. Reinstall blade.

5. Return mower to upright position.

6. Push down on arm, install new belt on gearcase pulley. Release arm slowly.

NOTE: Always use factory approved belt to assure proper fit and long life.

7. Reinstall drive cover.

+ 33 hidden pages