Husqvarna 917374423 Owner’s Manual

Owner's Manual

Husqvarna

ROTARY LAWN MOWER

625 Series Briggs & Stratton Engine

Power-Propelled

22" Multi-Cut

Model No.

917.374423

• EspaSol, p. 20

CAUTION:

Read and follow all

Safety Rules and Instructions before operating this equipment

Husqvarna, Charlotte, NC 28269

Visit our website: www.husqvama.com

U.S.A.

Warranty ................................................... 2

Safety Rules .......................................... 2-4

Product Specifications .............................. 5

Assembly ! Pre-Operation ........................ 6

Operation ............................................. 7-12

Maintenance Schedule ........................... 12

IMPORTANT: This cutting machine is capable of amputating hands and feet and throwing ob-

jects. Failure to observe the following safety instructions could result in serious injury or death.

_i,Look for this symbol to point out im-

portant safety precautions. It means CAUTIONN! BECOME ALERTH!

YOUR SAFETY IS INVOLVED. &WARNING: In order to prevent accidental

starting when setting up, transporting, ad- justing or making repairs, always disconnect spark plug wire and place wire where it cannot

come in contact with plug.

&WARNING: Engine exhaust, some of its

constituents, and certain vehicle compo- nents contain or emit chemicals known to

the State of California to cause cancer and

birth defects or other reproductive harm.

&WARNING: Battery posts, terminals and

related accessories contain lead and lead compounds, chemicals known to the State

of California to cause cancer and birth defects or other reproductive harm. Wash

hands after handling.

CAUTION: Muffler and other engine

parts become extremely hot during operation and

remain hot after engine has stopped. To avoid

severe burns on contact, stay away from these areas.

I. GENERAL OPERATION

• Read, understand, and follow all instructions on the machine and in the

manual(s) before starting. Be thoroughly

familiar with the controls and the proper

use of the machine before starting.

• Do not put hands or feet near or under rotating parts. Keep clear of the dis- charge opening at all times.

• Only allow responsible individuals, who are familiar with the instructions, to

operate the machine.

• Clear the area of objects such as rocks, toys, wire, bones, sticks, etc., which could be picked up and thrown by blade.

• Be sure the area is clear of other people before mowing. Stop the machine if anyone enters the area.

Maintenance ...................................... 12-15

Service and Adjustments ................... 15-17

Storage .............................................. 17-18

Troubleshooting ................................. 18-19

Repair Parts ....................................... 38-47

• Do not operate the mower when bare- foot or wearing open sandals. Always

wear substantial foot wear.

• Do not pull mower backwards unless abso- lutely necessary. Always Iookdown and be- hind before and while moving backwards.

• Never direct discharged material toward anyone. Avoid discharging material against

a wall or obstruction. Material may richo- chet back toward the operator. Stop the blade when crossing gravel surfaces.

• Do not operate the mower without proper guards, plates, grass catcher or other safety protective devices in place.

• See manufacturer's instructions for proper operation and installation of

accessories. Only use accessories ap- proved by the manufacturer.

• Stop the blade(s) when crossing gravel drives, walks, or roads.

• Stop the engine (motor) whenever you leave the equipment, before cleaning the mower or unclogging the chute.

• Shut the engine (motor) off and wait until the blade comes to complete stop before removing grass catcher.

• Mowonly in daylight orgood artificial light.

• Do not operate the machine while under the influence of alcohol or drugs.

• Never operate machine in wet grass. Always be sure of your footing: keep a

firm hold on the handle; walk, never run.

• Disengage the self-propelled mech- anism or drive clutch on mowers so

equipped before starting the engine.

• If the equipment should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibra- tion is generally a warning of trouble.

• Always wearsafety goggles or safetyglass- es with side shields when operating mower.

II. SLOPE OPERATION Slopes are a major factor related to slip &

fall accidents which can result in severe injury. All slopes require extra caution. If

2 you feel uneasy on a slope, do not mow it.

DO:

• Mowacrossthefaceofslopes:never up anddown.Exerciseextremecaution

whenchangingdirectionon slopes.

• Removeobstaclessuchas rocks,tree limbs,etc.

• Watchfor holes,ruts,or bumps.Tall grasscanhideobstacles.

DONOT:

• Donottrimneardrop-offs,ditchesor embankments.Theoperatorcouldlose

footingor balance.

• Donottrimexcessivelysteepslopes.

• Donotmowonwetgrass.Reduced

footingcouldcauseslipping.

III. CHILDREN

Tragicaccidentscanoccuriftheoperatoris

notalerttothepresenceofchildren.Children

are oftenattractedto the machineandthe

mowingactivity.Never assume that children

will remain where you last saw them.

• Keep children out of the trimming area and under the watchful care of another

responsible adult.

• Be alert and turn machine off if children enter the area.

• Before and while walking backwards, look behind and down for small children.

• Never allow children to operate machine.

• Use extra care when approaching blind corners, shrubs, trees, or other objects

that may obscure vision.

IV. SAFE HANDLING OF GASOLINE

Use extreme care in handling gasoline. Gasoline is extremely flammable and the

vapors are explosive.

• Extinguish all cigarettes, cigars, pipes and other sources of ignition.

• Use only an approved container.

• Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling.

• Never refuel the machine indoors.

• Never store the machine or fuel contain- er where there is an open flame, spark

or pilot light such as a water heater or on other appliances.

• Never fill containers inside a vehicle, on

a truck or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before filling.

• Remove gas-powered equipment from the truck or trailer and refuel it on the

ground. If this is not possible, then refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do

not use a nozzle lock-open device.

• If fuel is spilled on clothing, change clothing immediately.

• Never overfill fuel tank. Replace gas cap and tighten securely.

V. GENERAL SERVICE

• Never run machine inside a closed area.

• Never make adjustments or repairs with the engine (motor) running. Disconnect the spark plug wire, and keep the wire away

from the plug to prevent accidental starting.

• Keep nuts and bolts, especially blade attachment bolts, tight and keep equip- ment in good condition.

• Never tamper with safety devices. Check their proper operation regularly.

• Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spill-

age. Allow machine to coot before storing.

• Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.

• Never attempt to make wheel height adjustments while the engine is running.

• Grass catcher components are subject to wear, damage, and deterioration, which

could expose moving parts or allow objects to be thrown. Frequently check compo- nents and replace with manufacturer's recommended parts, when necessary.

• Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra caution when servicing them.

• Do not change the engine governor set- ting or overspeed the engine.

• Maintain or replace safety and instruc- tion labels, as necessary.

&WARNING: This lawn mower is equipped with an internal combustion engine and

should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the state of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal

lands. A spark arrester for the muffler is available through your nearest Husqvarna or other authorized service center (See the REPAIR PARTS section of this manual).

SECTION 1: LIMITED WARRANTY

Husqvarna Forest & Garden Company ("Husqvarna")

warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the date of purchase for the "Warranty Period" of

the product as set forth below: 2 YEAR NON-COMMERCIAL WARRANTY: Automatic

Mower, Riding lawn mowers, yard and garden tractors,

walk behind mowers, tillers, chain saws, trimmers,

brushcutters, clearing saws, snow blowers, handheld blowers, backpack blowers, hedge trimmers, electri-

cal products and power-assist collection systems for

noncommercial, nonorofessional, noninstitutional or nonincome _roducina use. except as herein stated.

Emission control system components necessary to

comply with CARB-TIER-II and EPA regulations.

Husqvarna Safety Apparel carries a 90-day warranty from the date of the customer's original purchase for defects in material and workmanship. Normal wear, tear or abuse is not covered under warranty. Product

must be returned to Charlotte with a warranty claim form. All care and maintenance instructions must be

followed as stated by the manufacturer on the care la-

bel. The fit of the protective apparel/boot is not covered

under warranty.

SECTION 2: HUSQVARNA'S OBLIGATIONS UNDER THE WARRANTY

Husqvarna will repair or replace defective components without charge for parts or labor if a component fails

because of a defect in material or workmanship during the warranty period.

SECTION 3: ITEMS NOT COVERED BY THIS WAR-

RANTY The following items are not covered by this warranty:

(1)Normal customer maintenance items which become

worn through normal regular use, including, but not limited to, belts, blades, blade adapters, bulbs, filters, guide bars, lubricants, rewind springs, saw chain, spark plugs, starter ropes and tines;

(2) Natural discoloration of material due to ultraviolet

light;

(3)Lawn and garden attachments are covered by a

third party which gives a warranty, all claims for warranty should be sent to the manufacturer; and

(4)Emission Control System components necessary

to which are manufactured by third party engine manufacturer.

SECTION 4: EXCEPTIONS AND LIMITATIONS This warranty shall be inapplicable to defects resulting

from the following:

(1)Accident, abuse, misuse, negligence and neglect,

including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any adverse reaction due to incorrect

storage or use habits;

(2)Failure to operate or maintain the unit in ac-

cordance with the Owner's/Operator's manual or instruction sheet furnished by Husqvarna;

(3)Alterations or modifications that change the

intended use of the product or affects the product's performance, operation, safety, or durability, or

causes the product to fail to comply with any ap- plicable laws; or:

(4)Additional damage to parts or components due to

continued use occurring after any of the above.

REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUEN- TIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT TO THE EXTENT PROHIBITED BY AP- PLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICU- LAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO THE WARRANTY PERIOD AS DEFINED IN THE LIMITED WARRANTY STATEMENT. HUSQVARNA RESERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE PRODUCT

WITHOUT NOTICE, AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY MANUFAC-

TURED PRODUCTS. Some states do not allow the exclusion of incidental

or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

SECTION 5: CUSTOMER RESPONSIBILITIES The product must exhibit reasonable care, mainte-

nance, operation, storage and general upkeep as written in the maintenance section of the Owner's/

Operator's manual. Should an operational problem or failure occur, the product should not be used, but delivered as is to an authorized Husqvarna dealer for evaluation. Proof of purchase, as explained in section 6, rests solely with the customer.

SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION It is the Owner's and Dealer's responsibility to make

certain that the Warranty Registration Card is properly filled out and mailed to Husqvarna Forest & Garden Company. This card should be mailed within ten (10) days from the date of purchase in order to confirm the warranty and to facilitate post-sale service.

Proof of purchase must be presented to the authorized Husqvarna dealer in order to obtain warranty service. This proof must include date purchased, model num- ber, serial number, and complete name and address of the selling dealer.

To obtain the benefit of this warranty, the product believed to be defective must be delivered to an

authorized Husqvarna dealer in a timely manner, no later than thirty (30) days from date of the operational

problem or failure. The product must be delivered at the owner's expense. Pick-up and delivery charges are

not covered by this warranty. An authorized Husqvarna dealer can be normally located through the "Yellow Pages" of the local telephone directory or by calling 1-800-HUSKY62 for a dealer in your area.

HUSQVARNA

7349 Statesville Road

Charlotte, NC 28269

531 83 81-23 2002

Serial Number: Date of Purchase:

Gasoline Capacity / Type: 1.6 Quarts (Unleaded Regular) Oil Type (API SG-SL): SAE 30 (above 32°F); SAE 5W-30 (below 32°F) Oil Capacity: 20 Ounces Spark Plug (Gap: .030") Champion J19LM or RJ19LM Blade Bolt Torque: 35-40 ft. Ibs.

• The model and serial numbers will be found on a decal on the rear of the lawn mower housing. Record both serial number and date of purchase in space provided above.

These accessories were available when this lawn mower was produced. They are not shipped with your mower. They are also available at most Husqvarna retailers and service centers. Some of these accessories may not apply to your lawn mower.

LAWN MOWER PERFORMANCE

CLIPPING

DEFLECTORS

FOR

REAR DISCHARGE

LAWN MOWERS

STABILIZER

GRASS CATCHERS

FOR

REAR DISCHARGE

LAWN MOWERS

LAWN MOWER MAINTENANCE

MUFFLERS

BELTS BLADES BLADE ADAPTERS

AIR FILTERS

GRASS CATCHERS

SIDE DISCHARGE

LAWN MOWERS

WHEELS

FOR

SPARK PLUGS

ENGINE OIL

Read these instructions and this manual in its entirety before you attempt to assemble or

operate your new lawn mower.

IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine.

Your new lawn mower has been assembled at the factory with the exception of those parts

left unassembled for shipping purposes. To ensure safe and proper operation of your lawn mower, all parts and hardware you assemble must be tightened securely. Use the correct

tools as necessary to ensure proper tightness. All parts such as nuts, washers, bolts, etc.,

necessary to complete the assembly have been placed in the parts bag.

TO REMOVE MOWER FROM CARTON

1. Remove loose parts included with mower.

2. Cut down two end corners of carton and lay end panel down flat.

3. Remove all packing materials except padding between upper and lower handle and padding holding operator

presence control bar to upper handle.

4. Roll lawn mower out of carton and check carton thoroughly for additional

loose parts.

HOW TO SET UP YOUR MOWER

TO UNFOLD HANDLE

IMPORTANT: Unfold handle carefully so

as not to pinch or damage control cables.

I. Raise handles until lower handle sec-

tion locks into place in mowing position.

2. Remove protective padding, raise up- per handle section into place on lower

handle and tighten both handle knobs.

3. Remove handle padding holding operator presence control bar to upper handle.

Your lawn mower handle can be adjusted for your mowing comfort. Refer to "AD- JUST HANDLE" in the Service and Adjust-

ments section of this manual. Operator MOWING

I: POSITION control bar

TO ASSEMBLE GRASS CATCHER

1. Put grass catcher frame into grass bag with rigid part of bag on the bottom.

Make sure the frame handle is outside of the bag top.

2. Slip vinyl bindings over frame. NOTE: If vinyl bindings are too stiff, hold

them in warm water for a few minutes. If bag gets wet, let it dry before using.

Vinyl Frame bindings opening

TO INSTALL ATTACHMENTS Your lawn mower was shipped ready to be

used as a mulcher. To convert mower to bagging or discharging, see "TO CON-

VERT MOWER" in the Operation section of this manual.

UP handle

Lower handle

Upper

Handle

knob

KNOW YOUR LAWN MOWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING

YOUR LAWN MOWER. Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments. Save this manual for

future reference.

These symbols may appear on your lawn mower or in literature supplied with the

product. Learn and understand their meaning.

CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER, KEEP HANDS

OR WARNING ON OFF AND FEET AWAY

Drive control

Operator presence control bar

Handle knob

Starter

Engine oil cap with dipstick

handle

Primer

Grass catche_

Muffler

Gasoline filler cap

Mulcher door

plug

Drive cover

Wheel adjuster

Housin( (on each wheel)

IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine.

MEETS CPSC SAFETY REQUIREMENTS Our rotary walk-behind power lawn mowers conform to the safety standards of the

American National Standards Institute and the U.S. Consumer Product Safety Com-

mission. The blade turns when the engine is running.

Operator presence control bar - must be held down to the handle to start the

engine. Release to stop the engine.

Primer- pumps additional fuel from the carburetor to the cylinder for use when

starting a cold engine.

Starter handle - used for starting engine. Mulcher door - allows conversion to

discharging or bagging operation. Drive control lever - used to engage power-propelled forward motion of mower.

Theoperationof any

SAFET_GLASSESlawnmowercanresult

inforeignobjectsthrown intotheeyes,which can resultinsevereeyedam-

age.Alwayswearsafetyglassesor eye shieldswhileoperatingyourlawnmower or performinganyadjustmentsor repairs. Werecommendastandardsafetyglasses

orwidevisionsafetymaskwornover spectacles.

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED

Engine speed was set at the factory for optimum performance. It is not adjustable.

ENGINE ZONE CONTROL ACAUTION: Federal regulations require

an engine control to be installed on this

lawn mower in order to minimize the risk of blade contact injury. Do not under

any circumstances attempt to defeat the function of the operator control. The blade turns when the engine is running.

• Your lawn mower is equipped with an operator presence control bar which

requires the operator to be positioned behind the lawn mower handle to start

and operate the lawn mower.

Operator presence control bar

ENGAGE DRIVE

DRIVE CONTROL

CONTROL DISENGAGED

DRIVE CONTROL ADJUSTMENT Over time, the drive control system may

become "loose", resulting in decreased speed. There is a turnbuckle on the underside of the drive control housing to

increase tension on the drive cable. Pro- ceed as follows:

1. Turn unit off and disconnect spark plug wire from spark plug.

2. Turn nut on underside of drive control to increase drive speed.

3. Operate mower to test drive speed. Readjust as required.

4. If condition fails to improve after the above steps (forward speed remains

the same), your drive belt is worn and should be replaced.

Drive control

lever

DRIVE CONTROL

• Self-propelling is controlled by hold- ing the operator presence control bar

down to the handle and pulling the drive control lever rearward to the handle. The farther toward the handle the lever

is pulled, the faster the unit will travel.

• Forward motion will stop when either the operator presence control bar or drive control lever are released. To stop

forward motion without stopping engine,

release the drive control lever only. Hold operator presence control bar down against handle to continue mowing

without self-propelling

NOTE: If after releasing the drive control the mower will not roll backwards, push the mower forward slightly to disengage

drive wheels.

• To keep drive control engaged when turning corners, push down on the

handle to lift the front wheels off the ground while turning lawn mower.

Adjustment turnbuckle

TO ADJUST CUTTING HEIGHT Raise wheels for low cut and lower wheels

for high cut, adjust cutting height to suit

your requirements. Medium position is best for most lawns.

• To change cutting height, squeeze ad- juster lever toward wheel. Move wheel

up or down to suit your requirements. Be

sure all wheels are in the same setting.

NOTE: Adjuster is properly positioned

when plate tab inserts into hole in lever. Also, 9-position adjusters (if so equipped)

allow lever to be positioned between the plate tabs.

LEVER BACKWARD TO LOWER MOWER

Plate tab

LEVER FORWARD TO RAISE MOWER Lever

TO CONVERT MOWER Your lawn mower was shipped ready to be

used as a mulcher. To convert to bagging

or discharging:

REAR BAGGING

• Open rear door, remove mulcher plug. Store mulcher plug in a safe place.

• You can now install the grass catcher or optional clipping deflector.

• To convert to mulching or discharging operation, install mulcher plug into rear discharge opening of mower.

Mulcher plug

SIDE DISCHARGING

• Mulcher plug must be installed into rear discharge opening of mower.

• Open mulcher door and install dis- charge deflector under door as shown.

• Mower is now ready for discharging operation.

• To convert to mulching or bagging operation, discharge deflector must be

removed and mulcher door closed.

MOWER IS NOW READY FOR DISCHARGING OPERATION

SIMPLE STEPS TO REMEMBER WHEN CONVERTING YOUR LAWN MOWER

FOR MULCHING -

1. Rear mulcher plug installed.

2. Mulcher door closed. FOR REAR BAGGING -

1. Rear mulcher plug removed.

2. Grass catcher installed.

3. Mulcher door closed. FOR SIDE DISCHARGING -

1. Rear mulcher plug installed.

_1 Discharge deflector installed.

CAUTION: Do not run your lawn mower without mulcher plug or approved grass catcher in place. Never attempt to operate the lawn mower with the rear door removed or propped open.

TO EMPTY GRASS CATCHER

1. Lift up on grass catcher using the frame handle.

2. Remove grass catcher with clippings from under lawn mower handle.

3. Empty clippings from bag.

NOTE: Do not drag the bag when empty- ing; it will cause unnecessary wear.

Open mulcher door

Discharge deflector

Grass

catcher

frame

>j-

BEFORE STARTING ENGINE

ADD OIL

Your lawnmower is shipped without oil in the engine. For type and grade of oil to

use, see "ENGINE" in the Maintenance

section of this manual. A CAUTION: DO NOT overfill engine with

oil, or it will smoke heavily from the muffler on startup.

1. Be sure lawnmower is level.

2. Remove oil dipstick from oil fill spout.

3. You receive a container of oil with the unit. Slowly pour the entire container

down the oil fill spout into the engine.

NOTE: Initial oil fill requires only 18 oz.

due to residual oil in engine from the

manufacturers 100% quality testing. When changing oil you may need 20 oz.

4. Insert and tighten dipstick. IMPORTANT:

• Check oil level before each use. Add oil

if needed. Fill to full line on dipstick.

• Change the oil after every 25 hours of

operation or each season. You may need to change the oil more often under dusty, dirty conditions. See "TO

CHANGE ENGINE OIL" in the Mainte- nance section of this manual.

ADD GASOLINE

• Fill fuel tank to bottom of tank filler neck.

Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel fresh-

ness.

A CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline

near an open flame.

A CAUTION: Alcohol blended fuels

(called gasohol or using ethanol or metha- nol) can attract moisture which leads to

separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To

avoid engine problems, the fuel system

should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel

next season. See Storage Instructions for additional information. Never use engine

or carburetor cleaner products in the fuel tank or permanent damage may occur.

gine

oil cap

Gasoline filler cap

Primer

TO STOP ENGINE

• To stop engine, release operator pres- ence control bar.

TO START ENGINE NOTE: Due to protective coatings on the

engine, a small amount of smoke may be present during the initial use of the prod-

uct and should be considered normal.

1. To start a cold engine, push primer three (3) times before trying to start. Use a firm push. This step is not usually necessary when starting an engine which has already run for a few

minutes.

2. Hold operator presence control bar down to the handle and pull starter handle quickly. Do not allow starter rope to snap back.

NOTE: In cooler weather it may be necessary to repeat priming steps. In

warmer weather over priming may cause

flooding and engine will not start. If you do flood engine, wait a few minutes before attempting to start and do not repeat priming steps.

MOWING TIPS

CAUTION: Do not use de-thatcher

blade attachments on your mower. Such

attachments are hazardous, will damage your mower and could void your warranty.

• Under certain conditions, such as very tall grass, it may be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of grass clip- pings. It may also be necessary to re- duce ground speed and/or run the lawn

mower over the area a second time.

• For extremely heavy cutting, reduce the

width of cut by overlapping previously

cut path and mow slowly.

• For better grass bagging and most cut- ting conditions, the engine speed should be set in the FAST position.

• Pores in cloth grass catchers can be- come filled with dirt and dust with use

and catchers will collect less grass. To prevent this, regularly hose catcher off

with water and let dry before using.

• Keep top of engine around starter clear and clean of grass clippings and chaff. This will help engine air flow and extend engine life.

MULCHING MOWING TIPS IMPORTANT: For best performance,

keep mower housing free of built-up grass and trash. See "CLEANING" in the

Maintenance section of this manual.

• The special mulching blade will recut the grass clippings many times and

reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the

mulched grass will biodegrade quickly to provide nutrients for the lawn. Always

mulch with your highest engine (blade) speed as this will provide the best recut-

ting action of the blades.

• Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and

interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has

dried, yet the newly cut area will not be exposed to direct sunlight.

• For best results, adjust the lawn mower

cutting height so that the lawn mower

cuts off only the top one-third of the grass blades. If the lawn is overgrown it will be necessary to raise the height of

cut to reduce pushing effort and to keep from overloading the engine and leaving

clumps of mulched grass. For extremely

heavy grass, reduce your width of cut

by overlapping previously cut path and

mow slowly.

1/3

• Certain types of grass and grass conditions may require that an area be

mulched a second time to completely hide the clippings. When doing a sec-

ond cut, mow across (perpendicular) to the first cut path.

• Change your cutting pattern from week

to week. Mow north to south one week then change to east to west the next

week. This will help prevent matting and graining of the lawn.

MAINTENANCE

SCHEDULE

Check for Loose Fasteners

_ Clean / Inspect Grass Catcher *

Check Tires

_ Check Drive Wheels

Clean Lawn Mower ....

M Clean under Drive Cover ***

O Check Drive Belt / Pulleys ***

_ Check / Sharpen / Replace Blade

R Lubrication

Clean and Recharge Battery ** Check Engine Oil level

E Change Engine Oil N Clean Air Filter

_ Inspect Muffler

N Replace Spark Plug E Replace Air Filter Paper Cartridge

Empty fuel system or add Stabilizer

* (if so equipped)

** Electric-Start mowers

*** Power-Propelled mowers

**** Use a scraper

to clean under deck

1 - Change more often if operating under a heavy load or in high outdoor temperatures. 2 - Service more often if operating in dirty or dusty conditions, 3 - Replace blades more often when mowing in sandy soil, 4 - Charge 48 hours at end of season.

5 - And after each 5 hours of use.

BEFORE AFTER EVERY EVERY EVERY BEFORE

EACH EACH 10 25 HOURS 100 STORAGE

USE USE HOURS OR SEASON HOURS

i/ i/

i/ i/3

1,4

14 i/

i/ 14

GENERAL RECOMMENDATIONS

The warranty on this lawn mower does not

cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must

maintain unit as instructed in this manual.

Some adjustments will need to be made

periodically to properly maintain your unit. At least once a season, check to see if you should make any of the adjustments described in the Service and Adjustments

section of this manual.

• At least once a year, replace the spark plug, clean or replace air filter element and check blade for wear. A new spark

plug and clean/new air filter element assure proper air-fuel mixture and help your engine run better and last longer.

• Follow the maintenance schedule in this manual.

BEFORE EACH USE

• Check engine oil level.

• Check for loose fasteners.

LU BRICATION Keep unit well lubricated

(See "LUBRICATION CHART").

LUBRICATION CHART

Wheel

adjuster (on

each wheel)

@ Engine oil

Mulcher

door hinge

@ Rear door

hinge

@ Handle bracket mounting pins

_ Spray lubricant

See "ENGINE" in Maintenance section.

IMPORTANT: Do not oil or grease plastic

wheel bearings. Viscous lubricants will

attract dust and dirt that will shorten the life of the self-lubricating bearings. If you feel they

must be lubricated, use only a dry, powdered graphite type lubricant sparingly.

LAWN MOWER

Alwaysobservesafetyruleswhenper- forminganymaintenance.

TIRES

• Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

• Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

DRIVE WHEELS Check front drive wheels each time before

you mow to be sure they move freely. The wheels not turning freely means trash, grass cuttings, etc. are in the drive wheel

area and must be cleaned to free drive

wheels.

If necessary to clean the drive wheels, be

sure to clean both front wheels.

1. Remove hubcaps, Iocknuts & washers.

2. Remove wheels from wheel adjusters.

3. Remove any trash or grass cuttings

from inside the dust cover, pinion and/ or drive wheel gear teeth.

4. Put wheels back in place. NOTE: If after cleaning, the drive wheels

do not turn freely, contact a Husqvarna or other qualified service center.

BLADE CARE For best results, blade must be kept

sharp. Replace a bent or damaged blade.

CAUTION: Use only a replacement

blade approved by the manufacturer of

your mower. Using a blade not approved

by the manufacturer of your mower is haz-

ardous, could damage your mower and void your warranty.

TO REMOVE BLADE

1. Disconnect spark plug wire from spark

plug and place wire where it cannot come in contact with plug.

2. Turn lawn mower on its side. Make

sure air filter and carburetor are up.

3. Use a wood block between blade and

mower housing to prevent blade from

turning when removing blade bolt. NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4. Remove blade bolt by turning counter- clockwise.

5. Remove blade & attaching hardware (bolt, lock washer & hardened washer).

Blade adapter

Lockwasher _

Blade \ bolt Hardened

washer

TO REPLACE BLADE

1. Position blade on the blade adapter aligning the two (2) holes in the blade

with the raised lugs on the adapter.

2. Be sure the trailing edge of blade (op- posite sharp edge) is up toward the

engine.

3. Install the blade bolt with the lock

washer and hardened washer into

blade adapter and crankshaft.

4. Use block of wood between blade and lawn mower housing and tighten the

blade bolt, turning clockwise.

Recommendedtighteningtorque:35-40ft.lbs. IMPORTANT: Blade bolt is heat treated.

If bolt needs replacing, replace only with

approved bolt shown in the Repair Parts section of this manual. TO SHARPEN BLADE

NOTE: We do not recommend sharp- ening the blade - but if you do, be sure the

blade is balanced. Care should be taken to keep the blade balanced. An unbal-

anced blade will cause eventual damage to mower or engine.

• The blade can be sharpened with a file

or on a grinding wheel. Do not attempt to sharpen while on the mower.

• To check blade balance, drive a nail into

a beam or wall. Leave about one inch of

the straight nail exposed. Place center

hole of blade over the head of the nail. If blade is balanced, it should remain in

a horizontal position. If either end of the

blade moves downward, sharpen the heavy end until the blade is balanced.

GRASS CATCHER

• The grass catcher may be hosed with

water, but must be dry when used.

• Check your grass catcher often for dam-

age or deterioration. Through normal

use it will wear. If catcher needs replac- ing, replace only with approved replace- ment catcher shown in the Repair Parts

section of this manual. Give the lawn

mower model number when ordering.

Key _-

,/ (

Crankshaft

GEARCASE

• To keep your drive system working properly, the gear case and area around the drive should be kept clean and free of trash build-up. Clean under the drive

cover twice a season.

• The gear case is filled with lubricant to the proper level at the factory. The only

time the lubricant needs attention is if service has been performed on the gear

case.

• If lubricant is required, use only Texaco Starplex Premium 1 Grease, Part No.

750369. Do not substitute.

ENGINE LU BRICATION

Use only high quality detergent oil rated with

API service classification SG-SL. Select the oil's SAE viscosity grade according to your

expected operating temperature.

SAE VISCOSITY GRADES

F -20 0 30 32 40 60 80 100

c -_0 -2? -1; ; _; 10 _o 4?

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT O{L CHANGE

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in

cold weather, these multi-viscosity oils will result in increased oil consumption when

used above 32°F. Check your engine oil level more frequently to avoid possible

engine damage from running low on oil.

Change the oil after every 25 hours of op-

eration orat least once a year if the mower

is not used for 25 hours in one year. Check the crankcase oil level before

starting the engine and after each five (5)

hours of continuous use. Tighten oil plug

securely each time you check the oil level. TO CHANGE ENGINE OIL

NOTE: Before tipping lawn mower to

drain oil, empty fuel tank by running en- gine until fuel tank is empty.

1. Disconnect spark plug wire from spark

plug and place wire where it cannot come in contact with plug.

2. Remove engine oil cap; lay aside on a clean surface.

3. Tip lawn mower on its side as shown and drain oil into a suitable container.

Rock lawn mower back and forth to re-

move any oil trapped inside of engine.

Containel

4. Wipe off any spilled oil from lawn mower or side of engine.

5. Slowly pour oil down the oil fill spout, stopping every few ounces to check the oil level with the dipstick.

6. Stop adding oil when you reach the FULL mark on the dipstick. Wait a

minute to allow oil to settle.

7. Continue adding small amounts of oil, rechecking the dipstick until oil level settles at FULL. DO NOT overfill, or engine will smoke heavily from the muffler on startup.

8. Always be sure to retighten oil dipstick before starting engine.

9. Reconnect spark plug wire to spark plug.

AIR FILTER

Your engine will not run properly and may be damaged by using a dirty air filter. Replace the air filter cartridge every 100 hours of operation or every season, which-

ever occurs first. Service air cleaner more often under dusty conditions.

TO CLEAN AIR FILTER

1. Loosen screw and tilt cover to remove.

2. Carefully remove cartridge.

3. Clean by gently tapping on a flat sur-

A face. If very dirty, replace cartridge.

CAUTION: Petroleum solvents, such

as kerosene, are not to be used to clean cartridge. They may cause deterioration

of the cartridge. Do not oil cartridge. Do not use pressurized air to clean or dry cartridge.

4. Install cartridge, then replace cover. Be sure tabs are aligned with slots in the back plate. Fasten screw securely.

Back plate

Cartridge _ / ,

_ Slot

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG Replace spark plug at the beginning of

each mowing season or after every 100

hours of operation, whichever occurs first. Spark plug type and gap setting are shown

in the "PRODUCT SPECIFICATIONS"

section of this manual.

Cover

CLEANING

IMPORTANT: For best performance,

keep mower housing free of built-grass

and trash. Clean the underside of your mower after each use.

_IbCAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

• Clean the underside of your lawn mower by scraping to remove build-up

of grass and trash.

• Clean engine often to keep trash from

accumulating. A clogged engine runs

tab

hotter and shortens engine life.

• Keep finished surfaces and wheels free

of all gasoline, oil, etc.

• We do not recommend using a garden hose to clean lawn mower unless the

electrical system, muffler, air filter and

carburetor are covered to keep water

out. Water in engine can result in short- ened engine life.

CLEAN UNDER DRIVE COVER Clean under drive cover at least twice a sea- son. Scrape underside of cover with putty

knife or similar tool to remove any build-up

of trash or grass on underside of drive cover.

_L WARNING: To avoid serious injury, before performing any service and adjustments:

1. Release control bar and stop engine.

2. Make sure the blade and all moving parts have completely stopped.

3. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

LAWN MOWER

TO ADJUST CUTTING HEIGHT

See "TO ADJUST CUTTING HEIGHT" in

the Operation section of this manual.

REAR DEFLECTOR

The rear deflector, attached between the rear wheels of your mower, is provided to minimize the possibility that objects will

be thrown out of the rear of the mower

into the operator mowing position. If the deflector becomes damaged, it should be replaced.

+ 33 hidden pages