Husqvarna SRD17530, 917280020 Owner’s Manual

( )

Operator's Manual

Gasoline containing up to 10% ethanol (EIO) is acceptable for use in this machine.

The use of any gasoline exceeding 10% ethanol (EIO) will void the product warranty.

532 44 10-43

Safe Operation Practices for Ride=On Mowers

DANGER: THiS CUTTING MACHINE iS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE

TO OBSERVE THE FOLLOWING SAFETY iNSTRUCTiONS COULD RESULT iN SERIOUS iNJURY OR DEATH.

_) WARNING: Inordertopreventaccidental

_) are recommended by and comply with

starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.

tral, you may lose control of the tractor.

WARNING: Donot coast down a hill inneu-

WARN ING: Towonly the attachments that specifications of the manufacturer of your

tractor. Use common sensewhen towing. Operate only at the lowest possible speed

when on a slope. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

WARNING

Engine exhaust, some of itsconstituents, and certain

vehicle components contain or emit chemicals

known to the State of California to cause cancer

and birth defects or other reproductive harm.

WARNING

Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known

to the State of California to cause cancer and birth

defects or other reproductive harm. Wash hands

after handling.

I. GENERAL OPERATION

Read, understand, and follow all instructions on the machine and in the manual before starting. Do not put hands or feet near rotating parts or under

the machine. Keep clear of the discharge opening at all times.

Only allow responsible adults, who are familiar with the instructions, to operate the machine. Clear the area of objects such as rocks,toys, wire, etc., which could be picked up and thrown by the blades.

Be sure the area is clear of bystanders before

operating. Stop machine if anyone enters the area.

• Never carry passengers. Do not mow in reverse unless absolutely necessary.

Always look down and behind before and while

backing. Never direct discharged material toward anyone. Avoid

discharging material against a wall or obstruction.

Material may ricochet back toward the operator. Stop

the blades when crossing gravel surfaces.

Do not operate machine without the entire grass catcher,

discharge chute, or other safety devices in place and working.

SAFETY RULES

• Slow down before turning.

• Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and

remove keys before dismounting.

• Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or

unclogging the discharge chute.

• Operate machine only in daylight or good artificial

light.

• Do not operate the machine while under the influence of alcohol or drugs.

• Watch for traffic when operating near or crossing

roadways.

• Use extra care when loading or unloading the machine

into a trailer or truck.

• Always wear eye protection when operating

machine.

• Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower-

related injuries. These operators should evaluate their

ability to operate the riding mower safely enough to

protect themselves and others from serious injury.

• Follow the manufacturer's recommendation for wheel weights or counterweights.

• Keep machine free of grass , leaves or other debris

build-up which can touch hot exhaust / engine parts and burn. Do not allow the mower deck to plow leaves or other debris which can cause build-up to occur.

Clean any oil or fuel spillage before operating or storing the machine. Allow machine to cool before storage.

II. SLOPE OPERATION

Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or

death. Operation on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it,

do not mow it.

• Mow up and down slopes, not across.

• Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could overturn the machine. Tall grass can hide obstacles.

• Choose a low ground speed so that you will not have to stop or shift while on the slope.

• Do not mow on wet grass. Tires may lose traction. Always keep the machine in gear when going down

slopes. Do not shift to neutral and coast downhill.

• Avoid starting, stopping, or turning on a slope. If the tires lose traction, disengage the blades and proceed slowly straight down the slope.

• Keep all movement on the slopes slow and gradual.

Do not make sudden changes in speed or direction,

which could cause the machine to roll over.

• Use extra care while operating machine with grass catchers or other attachments; they can affect the

stability of the machine. Do no use on steep slopes.

• Do not try to stabilize the machine by putting your foot on the ground.

• Do not mow near drop-offs, ditches, or embankments. The machine could suddenly roll over ifawheel is over the edge or if the edge caves in.

SAFETY RULES

ill. CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to

the machine and the mowing activity. Never assume that children will remain where you last saw them.

• Keep children out ofthe mowing area and inthe watchful care of a responsible adult other than the operator.

• Be alert and turn machine off if a child enters the

area.

• Before and while backing, look behind and down for

small children.

• Never carry children, even with the blades shut off. They

may fall off and be seriously injured or interfere with

safe machine operation. Children who have been given

rides in the past may suddenly appear in the mowing

area for another ride and be run over or backed over

by the machine.

• Never allow children to operate the machine.

• Useextra care when approaching blind corners, shrubs,

trees, or other objects that may block your view of a child.

IV. TOWING

• Tow only with a machine that has a hitch designed for towing. Do not attach towed equipment except at the

hitch point.

• Follow the manufacturer's recommendation for weight

limits for towed equipment and towing on slopes.

• Never allow children or others in or on towed equipment.

• On slopes, the weight of the towed equipment may cause loss of traction and loss of control.

• Travel slowly and allow extra distance to stop.

V. SERVICE

SAFE HANDLING OF GASOLINE

To avoid personal injury or property damage, use extreme care inhandling gasoline. Gasoline isextremely flammable

and the vapors are explosive.

• Extinguish all cigarettes, cigars, pipes, and other sources of ignition.

• Use only approved gasoline container.

• Never remove gas cap or add fuel with the engine

running. Allow engine to cool before refueling.

• Never fuel the machine indoors.

• Never store the machine orfuel container where there

isan open flame, spark, or pilot light such as on a water heater or other appliances.

• Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner. Always place containers

on the ground away from your vehicle when filling.

• Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment with a portable container,

rather than from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim ofthe fuel tank or container opening at all times until fueling is complete.

Do not use a nozzle lock-open device.

• If fuel is spilled on clothing, change clothing immedi- ately.

• Never overfill fuel tank. Replace gas cap and tighten securely.

Safe Operation Practices for Ride=On Mowers

GENERALSERVlCE

Never operate machine in a closed area.

Keep all nuts and bolts tight to be sure the equipment is in safe working condition.

• Never tamper with safety devices. Check their proper operation regularly.

• Keep machine free of grass, leaves, or other debris

build-up. Clean oil or fuel spillage and remove any fuel-

soaked debris. Allow machine to cool before storing.

• If you strike a foreign object, stop and inspect the

machine. Repair, if necessary, before restarting.

• Never make any adjustments or repairs with the engine

running.

• Check grass catcher components and the discharge chute frequently and replace with manufacturer's rec- ommended parts, when necessary.

• Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them.

• Check brake operation frequently. Adjust and service as required.

• Maintain or replace safety and instruction labels, as

necessary.

Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area.

Never carry passengers.

Do not mow in reverse unless absolutely necessary.

Always look down and behind before and while back-

ing. Never carry children, even with the blades shut off. They

may fall off and be seriously injured or interfere with

safe machine operation. Children who have been given

rides in the past may suddenly appear in the mowing

area for another ride and be run over or backed over

by the machine.

Keep children out of the mowing area and in the watchful

care of a responsible adult other than the operator.

Be alert and turn machine off if a child enters the

area.

Before and while backing, look behind and down for

small children.

Mow up and down slopes (15° Max), not across.

Choose a low ground speed so that you will not have to stop or shift while on the slope.

Avoid starting, stopping, or turning on a slope. If the tires lose traction, disengage the blades and proceed slowly straight down the slope.

If machine stops while going uphill, disengage blades,

shift into reverse and back down slowly.

Do not turn on slopes unless necessary, and then, turn

slowly and gradually downhill, if possible.

PRODUCT SPECiFiCATiONS

Gasoline Capacity 1.50 Gallons and Type: Unleaded Regular

:3ilType SAE 30 (above 32°F) o API-SG-SL)' SAE 5W30 (below 32 F)

Oil Capacity: W/Filter: 56 oz.

Spark Plug: Champion RC12YC

Ground Speed Forward: 1st 1.0

(MPH): 2nd 1.4

Charging System: 3 Amps Battery

Battery: AMP/HR: 28

Blade Bolt Torque: 45-55 FT. LBS.

W/O Filter: 48 oz.

(Gap: .030")

3rd 2.1 4th 3.1

5th 4.0 6th 5.1

Reverse: 1.6

5 Amps Headlights Min. CCA: 230

Case Size: U1R

CONGRATULATIONS on your purchase of a new tractor.

Ithas been designed, engineered and manufactured to give

you the best possible dependability and performance. Should you experience any problem you cannot easily rem-

edy, please contact your nearest authorized service center/ department. We have competent, well-trained technicians and the proper tools to service or repair this tractor.

Please read and retain this manual. The instructions will

enable you to assemble and maintain your tractor properly. Always observe the "SAFETY RULES".

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in maintaining, caring for and using your tractor.

• Follow the instructions under "Maintenance" and "Stor- age" sections of this manual.

WARNING: This tractor is equipped with an internal com- bustion engine and should not be used on or near any

unimproved forest-covered, brush-covered orgrass-covered land unless the engine's exhaust system is equipped with

a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained

in effective working order by the operator.

A spark arrester for the muffler is available through your

nearest authorized service center/department. In the state of California the above is required by law

(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply

on federal lands.

TABLE F CONTENTS

SAFETY RULES ......................................................... 2=3

PRODUCT SPECIFICATIONS ....................................... 4

CUSTOMER RESPONSIBILITIES ................................. 4

ASSEMBLY ................................................................. 6=9

OPERATION ........................................................... 10-15

MAINTENANCE SCHEDULE ...................................... 16

MAINTENANCE ..................................................... 16-19

SERVICE AND ADJUSTMENTS ............................ 20-25

STORAGE ....................................................................26

TROUBLESHOOTING ............................................ 27-28

WARRANTY ............................................................ 29-32

UNASSEMBLED PARTS

Bagger

1/4 x 20 x 1.25"

Carriage Bolts

1/4 x20 x 1.15 Shoulder Bolts

Retainer Spring clip

Steering Wheel

Steering

Wheel

/ \

Steering

Wheel Insert

[ ]

Steering Wheel

Adapter

(1) Bolt

/ \

i_- _" \

I \ #/ \ I \,./# /I

Steering Boot

Steering

Extension

Shaft

1/4 x 20

Flange Lock Nuts

(1) Washer

(1) Bolt

Seat

Clevis Pin

(1) Seat

(1) Large (1) Lock

Flat Washer Washer

Slope Sheet

Key(s)

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use

the correct tools as necessary to ensure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 5/16" wrench Utility knife (2) 7/16" wrenches Tire pressure gauge

(2) 1/2" wrenches Pliers (1) 9/16" wrench

When right or left hand ismentioned inthis manual, itmeans when you are in the operating position (seated behind the

steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

Remove all accessible loose parts and parts cartons from carton.

• Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

• Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

TO CHECK BATTERY (See Fig. 1)

• Lift seat to raised position.

NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

• For battery and battery cable installation see "RE- PLACING BATTERY"in the "Service and Adjustments"

section in this manual.

INSTALL STEERING WHEEL

• Position front wheels of the tractor so they are pointing straight forward.

• Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

• Position steering wheel so cross bars are horizontal

(left to right) and slide inside boot and onto adapter.

• Assemble large flat washer, lock washer, hex bolt and tighten securely.

• Snap steering wheel insert into center ofsteeringwheel.

• Remove protective materials from tractor hood and grill.

iMPORTANT: CHECK FOR AND REMOVE ANY STAPLESIN SKIDTHAT MAYPUNCTURETIRESWHERE TRACTOR ISTO ROLL OFF SKID.

LARGE FLAT i_ .... L =_

:'+ LOCK

.;::'S;) ::: -.-. STEERING

,J_-_ ......._".....IWNEEL

" ::.:::: ::: :::; "

<-",'::_ STEERING

LOWE R STEERING

BOOT

LABEL

Fig. 1

TO INSTALL STEERING WHEEL (See Fig. 2)

ASSEMBLE EXTENSION SHAFT AND BOOT

• Slide extension shaft onto lower steering shaft.

• Place tabs of steering boot over tab slots in dash and push down to secure.

Fig. 2

INSTALL SEAT (See Figs. 3 and 4)

• Remove bolt and flat washer securing seat tocardboard packing and set aside for assembly of seat to tractor.

Remove the cardboard packing and discard.

• Connect switch to seat.

• Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan.

• Push down on seat to engage pads in slots and pull seat towards rear of tractor.

• Raise seat and tighten bolt securely.

• Remove tape and discard.

• Lower seat into operating position and sit on seat.

Press clutch/brake pedal all the way down. Ifoperating

position is not comfortable, adjust seat.

SEAT /

SWITCH

ASSEMBLY

TO INSTALL HOOD SCOOP (See Fig. 5)

PAD _

SLOT [

Fig. 3

I I

/ /

WiRiNG HARNESS

TAPE

TO ADJUST SEAT

• Grasp adjustment handle and pull up, slide seat to desired position and release adjustment handle.

SLOT TAPE

FLAT WASHER

SEAT PAN

BOLT TAB

Fig. 4

NOTE: You may now roll your tractor off the skid. Follow the instructions below to remove the tractor from the skid.

_IWARNIN6: Before starting, read, understand and follow

all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in

front of tractor is clear of other people and objects.

ADJUSTMENT

HANDLE

TO ROLLTRACTOR OFF SKiD (See Operation section for location and function of controls)

• Raise attachment lift lever to its highest position.

• Releaseparkingbrakebydepressingclutch/brakepedal.

• Place gearshift lever inneutral (N) position.

• Roll tractor forward off skid.

• Remove banding holding the deflector shield up against tractor.

Continue with the instructionsthat follow.

Fig. 5

ASSEMBLY

TO ASSEMBLY BAGGER (See Figs 6 =8)

• Unfold bag and stand right side up.

• Feed front bagger frame (1) up through fabric loops at each side of bagger.

• Snap bottom offront bagger frame (1) into snap feature at front of bagger bottom.

• Slide bagger fabric loop (2) segments at the ends of

bag onto top bagger frame tubing.

• Uninstall two (1\4"-20 x 1.15") hex bolts (3) from the front of top frame.

• Reinstall the two (1\4"-20 x 1.15") hex bolts (3) through

holes at top of the front bagger frame and thread into nuts inside the tubing of top bagger frame.

• Remove clevis pin (6) and retainer spring (7) from bagger handle (8).

• Slide bagger handle (8) down through bagger cover and frame upper weldment holes.

• Reinstall clevis pin (6) through hole at bottom of bag- ger handle and slide retainer spring (7) into hole at

the end of the clevis pin until it locks into place

Fig. 8

TO ADJUST BAGGER FULL LEVER/PADDLE (See Fig 9)

• Before adjusting, tractor engine must be shut off and parking brake engaged.

Fig. 6

• Uninstall (1/4"-20) lock nuts (4)at bottom offront bagger frame.

• Unfold cross braces (5) and attach to carriage bolts at

bottom corners of front bagger frame.

• Reinstall (1/4"-20) lock nuts (4) and tighten until fully seated.

Fig. 7

Fig. 9

• For the heaviest/wet grasses, remove paddle (3).

• For lighter grasses use the paddle (3) on setting "1",

"2", or "3" ("3" being for the lightest or dry grass).

• Choose your setting and rotate the bagger paddle (3) so that the desired number (setting) faces you.

• Setting may be changed by loosening fasteners (4 and

5), removing/rotating paddle (3), and tightening again.

ASSEMBLY

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important

for best cutting performance.

• Reduce tire pressure to PSI shown on tires.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be prop-

erly leveled. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF BELTS

See the figures that are shown for replacing motion and mower blade drive belts inthe Service and Adjustments sec-

tion of this manual. Verifythat the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that the brake is operating properly. See "TO CHECK BRAKE"

in the Service and Adjustments section of this manual.

Vf CHECKMST

BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST

PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIS_

J" All assembly instructions have been completed. J" No remaining loose parts in carton.

J" Battery is properly prepared and charged. J" Seat is adjusted comfortably and tightened securely.

J" All tires are properly inflated. (For shipping purposes,

the tires were overinflated at the factory).

J" Be sure mower deck is properly leveled side-to-side/

front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

J" Check mower and drive belts. Be sure they are routed

properly around pulleys and inside all belt keepers.

J" Check wiring. See that all connections are still secure

and wires are properly clamped.

WHILE LEARNING HOWTO USEYOUR TRACTOR, PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS:

J" Engine oil is at proper level. _/' Fuel tank is filled with fresh, clean, regular unleaded

gasoline.

J" Become familiar with all controls, their location and

function. Operate them before you start the engine. J" Be sure brake system is in safe operating condition. J" Be sure Operator Presence System and Reverse Op-

eration System (ROS) are working properly (See the

Operation and Maintenance sections in this manual).

OPERATION

These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.

L I',,I

REVERSE NEUTRAL HiGH

ENGINE OFF REVERSE ENGINE ON ENGINE START PARKING BRAKE PARKING BRAKE PARKING BRAKE

OPERATION LOCKED UNLOCKED

SYSTEM (ROS)

LOW CHOKE FAST SLOW

iGNiTiON SWITCH

OVER TEMP

LIGHT

FUEL OiL PRESSURE

BATTERY REVERSE FORWARD MOWER HEIGHT

MOWER LiFT

ATTACHMENT ATTACHMENT

CLUTCH DISENGAGED CLUTCH ENGAGED

LIGHTS ON

FREE WHEEL

(Automatic Models only)

Failure to follow instructions

could result in serious injury or death. The safety alert symbol

is used to identify safety inform-

ation about hazards which can

result in death, serious injury

and/or property damage.

DANGER, KEEP HANDS

AND FEET AWAY

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury. WARNING indicates a hazard which, if not avoided,

could result in death or serious injury. CAUTION indicates a hazard which, if not avoided,

might result in minor or moderate injury.

CAUTION when used without the alert symbol,

indicates a situation that could result in damage

to the tractor and/or engine.

HOT SURFACES indicates a hazard which, if not avoided, could result in death, serious injury

and/or property damage. FIRE indicates a hazard which, if not avoided,

could result in death, serious injury and/or

property damage.

KEEP AREA CLEAR SLOPE HAZARDS

(SEE SAFETY RULES SECTION)

OPERATION

KNOW YOUR TRACTOR

READ THiS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR

Compare the illustrationswith your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.

Our tractors conform to the applicable safety standards of the American National Standards Institute.

(A) ATTACHMENT LIFT LEVER - Used to raise and lower the mower or other attachments mounted to your tractor.

(B) BRAKE PEDAL - Used for braking the tractor and starting the engine.

(D) THROTTLE/CHOKE CONTROL - Used for starting and controlling engine speed.

(E) ATTACHMENT CLUTCH LEVER -Used to engage the mowerblades, orother attachmentsmountedtoyour tractor.

03078

Fig. 10

(F) IGNITION SWITCH - Used for starting and stopping the engine.

(G) REVERSE OPERATION SYSTEM (ROS) "ON" POSITION - Allows operation of mower or other powered

attachment while in reverse. (H) LIGHT SWITCH - Turns the headlights on and off.

(J) GEARSHIFT LEVER - Selects the speed and direction of the tractor.

+ 25 hidden pages