9030PW
Table of contents
Loading...
Operator’s manual
5525PW, 6026PW, 9030PW, 1335PW
Please read the operator’s manual carefully and make sure you
understand the instructions before using the machine.
English
English — 1
CONTENTS
Contents
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
KEY TO SYMBOLS . . . . . . . . . . . . . . . . . . . . .2
Symbols in the Operator’s Manual . . . . . . . . .2
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . .3
Dear Customer . . . . . . . . . . . . . . . . . . . . . . . . .3
WHAT IS WHAT? . . . . . . . . . . . . . . . . . . . . . . .4
What is what on the pressure washer . . . . . .4
FREQUENTLY ASKED QUESTIONS . . . . . . . .5
How do I start my pressure washer? . . . . . . .5
What type of oil do I use? . . . . . . . . . . . . . . .5
Why don’t I have any water pressure? . . . . . .5
How do I get high pressure? . . . . . . . . . . . . . .5
How do I get the soap suction to work? . . . .5
Why doesn’t the pressure washer apply
detergents with high pressure? . . . . . . . . . . .5
What maintenance do I need to perform
on my pressure washer? . . . . . . . . . . . . . . . . .5
Where can I buy accessories for my
pressure washer? . . . . . . . . . . . . . . . . . . . . . . .5
SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . .6
Important Safety Guidelines . . . . . . . . . . . . . .6
PRE-OPERATION . . . . . . . . . . . . . . . . . . . . . . .8
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Trigger Safety Latch . . . . . . . . . . . . . . . . . . . .10
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . .11
1. Surface preparation . . . . . . . . . . . . . . . . . .11
2. Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3. Initial High Pressure Rinse . . . . . . . . . . . . .12
Pressure Adjustment . . . . . . . . . . . . . . . .12
Adjusting the Spray Fan Angle . . . . . . .12
Angle to the Cleaning Surface . . . . . . . .13
Distance from Cleaning Surface . . . . . . .13
How to Avoid Damaging Surfaces . . . . .13
4. Detergent Application . . . . . . . . . . . . . . .13
Detergents . . . . . . . . . . . . . . . . . . . . . . . .13
General Cleaning Tips . . . . . . . . . . . . . . .14
5. Cleaning Power . . . . . . . . . . . . . . . . . . . . .14
6. Final Rinse . . . . . . . . . . . . . . . . . . . . . . . . .14
7. Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . .14
Pressure Relief Procedure . . . . . . . . . . . . . . .14
8. Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Long Term Storage Instructions
(More than 30 days in storage) . . . . . . .15
Tips for Extending the Life of Your
Pressure Washer . . . . . . . . . . . . . . . . . . .15
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .16
Engine Oil Changing Instructions . . . . . . . . .16
Check Pump Oil and Pump Oil Changing . .17
MAINTENANCE SCHEDULE . . . . . . . . . . . .18
TECHNICAL AND CONSUMER
INFORMATION . . . . . . . . . . . . . . . . . . . . . . .19
TROUBLESHOOTING CHART . . . . . . . . . . .20
CART PARTS LIST . . . . . . . . . . . . . . . . . . . . .23
5525PW Cart . . . . . . . . . . . . . . . . . . . . . . . . . .23
6026PW Cart . . . . . . . . . . . . . . . . . . . . . . . . . .24
9030PW Cart . . . . . . . . . . . . . . . . . . . . . . . . . .25
1335PW Cart . . . . . . . . . . . . . . . . . . . . . . . . . .25
PUMP PART LIST . . . . . . . . . . . . . . . . . . . . .26
5525PW Pump . . . . . . . . . . . . . . . . . . . . . . . .26
6026PW Pump . . . . . . . . . . . . . . . . . . . . . . . .27
9030PW Pump . . . . . . . . . . . . . . . . . . . . . . . .28
1335PW Pump . . . . . . . . . . . . . . . . . . . . . . . .28
IN466700AV 7/06
2 — English
Safety Guidelines
This manual contains information that is very
important to know and understand. This
information is provided for SAFETY and to PREVENT
EQUIPMENT PROBLEMS. To help recognize this
information, observe the following symbols.
Warning indicates a potentially
hazardous situation which, if not
avoided, COULD result in death or serious injury.
Caution indicates a potentially
hazardous situation which, if not
avoided, MAY result in minor or moderate injury.
Notice indicates important
information, that if not followed,
may cause damage to equipment.
NOTE: Information that requires special attention.
KEY TO SYMBOLS
Symbols in the Operator’s Manual
Please read the operator’s manual
carefully and make sure you
understand the intructions before
using the tool.
DO NOT overreach or stand on
unstable support. Keep good footing
and balance at all times.
Risk of injection or severe injury. Keep
clear of nozzle.
ALWAYS wear safety glasses or
goggles and protective equipment
(hearing protection, gloves, rubber
boots, protective clothing) when
operating or performing
maintenance.
Risk of explosion.
Risk of fire.
!
WARNING
!
CAUTION
NOTICE
English — 3
INTRODUCTION
Dear Customer,
Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition
that dates back to 1689, when the Swedish King Charles XI ordered the construction of a factory
on the banks of the Husqvarna River, for production of muskets. The location was logical, since
waterpower was harnessed from the Husqvarna River to create the water-powered plant. During
the more than 300 years of being, the Husqvarna factory has produced a lot of different products,
from wood stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles, etc. In
1956, the first motor driven lawn mowers appeared, followed by chain saws in 1959, and it is
within this area Husqvarna is working today.
Today, Husqvarna is one of the leading manufacturers in the world of forest and garden products,
with quality as our highest priority. The business concept is to develop, manufacture and market
motor driven products for forestry and gardening, as well as for the building and construction
industry. Husqvarna’s aim is also to be in the front edge according to ergonomics, usability, security
and environmental protection. That is the reason why we have developed many different features
to provide our products within these areas.
We are convinced that you will appreciate, with great satisfaction, the quality and performance of
our product for a very long time to come. The purchase of one of our products gives you access to
professional help with repairs and service whenever this may be necessary. If the retailer who sells
your machine is not one of our authorized dealers, ask for the address of your nearest service
workshop.
It is our wish that you will be satisfied with your product and that it will be your companion for a
long time. Think of this operator’s manual as a valuable document. By following its’ content (using,
service, maintenance, etc) the life span and the second-hand value of the machine can be
extended. If you will sell this machine, make sure that the buyer will get the operator’s manual.
Thank you for using a Husqvarna product.
Husqvarna AB has a policy of continuous product development and therefore reserves the right to
modify the design and appearance of products without prior notice.
For customer assistance call 704-921-7000 or contact us at our website: www.husqvarna.com
4 — English
WHAT IS WHAT?
1 Serial Number/Product Decal
2 Tip Holder with Spray Tips
3 Detergent Tank (5525PW, 6026PW)
4 Injection Tube (not shown)
5 Gun with trigger
6 Lance
7 Inlet Connection for High Pressure Hose
(not shown on 9030PW/1335PW)
8 Inlet Connection for Garden Hose
(not shown on 9030PW/1335PW)
9 Engine Oil Fill
10 Engine switch - On/Off
11 Throttle Control
12 Muffler
13 Choke
14 Fuel Tank
15 Pressure Adjusting Knob (models 9030PW,
1335PW)
16 Fuel Valve - On/Off
1
2
3
5
6
7
8
9
10
12
13
14
16
1
2
3
4
5
6
7
7
8
9
10
11
12
13
14
16
1
2
5
6
7
7
10
9
10
11
12
13
14
15
16
5525PW
6026PW
9030PW/1335PW*
English — 5
FREQUENTLY ASKED QUESTIONS
How do I start my pressure
washer?
1. Make sure you have gas and oil in the engine.
2. Turn the water on, then squeeze the trigger on
the gun to make sure the water will flow
smoothly out of the nozzle or tip.
3. Put the engine throttle control in the
“Fast/Start” position. Set the fuel valve to “ON”
Set the On/Off switch to “ON” (if applicable).
4. Close the choke.
5. Squeeze and hold the trigger (to relieve any
back pressure in the pump) while pulling the
starter cord.
6. If the engine does not start after three tries, see
Troubleshooting Section (Pages 20-21).
What type of oil do I use?
ENGINE
THE ENGINE DOES NOT COME FILLED WITH OIL. For
engine oil types and quantities refer to Pages 16
and 19 of this manual and also refer to the included
engine owner’s manual for oil changing instructions.
PUMP
See Page 17 for pump oil types and quantities.
Please note the 5525PW model has a pump that is
sealed and does not require service.
Why don’t I have any water
pressure?
• Is the water hose attached to the pressure
washer?
• Is the water turned on?
• Check for any kinks, leaks, or blockage in the
hoses, fittings, or the nozzle.
• Is the inlet filter screen free of debris? Check and
remove debris if needed.
• Is the quick connect tip in place? (See Page 9.)
How do I get high pressure?
• Use any color tip except black. The black tip is
only used for low pressure detergent application.
How do I get the soap
suction to work?
For Detergent Tanks:
1. Attach clear plastic tube to plastic barb on
detergent tank (see Figure 2).
2. Fill detergent tank with detergent formulated
for use with pressure washers.
3. Install the black spray tip to apply low pressure
detergent.
For Other Units:
1. Attach clear plastic tube to brass barb on pump
(see Figure 3).
2. Put the other filter end of the clear tube into
the detergent container.
3. Install the black spray tip to apply low pressure
detergent.
Why doesn’t the pressure
washer apply detergents
with high pressure?
The reason you don’t apply detergents with high
pressure is that the detergents “bounce” off the
cleaning surface as fast as you apply them.
Detergent is only effective when you allow it time
to work on the surface of whatever you are
cleaning. You can only apply detergent at low
pressure, wait 1-3 minutes to allow it to work, and
rinse the surface with high pressure.
What maintenance do I
need to perform on my
pressure washer?
1. After turning off the pressure washer and the
water, depressurize the hose by triggering the
gun.
2. Remove the garden hose and high pressure hose
from the pump.
3. Pull the start rope slowly five times to purge
water from the pump. This will help protect the
pump from damage.
4. DO NOT store your pressure washer in an area
where the temperature will drop below 32˚F /
0˚C) unless pressure washer is properly
winterized (see Page 15).
Where can I buy accessories
for my pressure washer?
• Call your local Husqvarna Dealer.
6 — English
SAFETY GUIDELINES
Important Safety Instructions
SAVE THESE INSTRUCTIONS
The engine exhaust from
this product contains chemicals
known to the State of California to cause cancer,
birth defects or other reproductive harm.
When using this product, basic precautions should
ALWAYS be followed, including the following:
• Read all instructions before using
the product.
• To reduce the risk of injury, close
supervision is necessary when the
product is used near children.
• Follow all safety codes as well as the Occupational
Safety and Health Act (OSHA).
• Ensure safety devices are operating properly
before each use. DO NOT remove or modify any
part of the gun or unit.
• Know how to stop this product and bleed
pressure quickly. Be thoroughly familiar with the
controls.
• Stay alert – watch what you are doing.
• DO NOT operate the product when fatigued or
under the influence of alcohol or drugs.
• Keep operation area clear of all persons.
• DO NOT overreach or stand on
unstable support. Keep good
footing and balance at all times.
• Follow the maintenance instructions
specified in the manual.
Risk of injection or
severe injury. Keep
clear of nozzle. DO NOT discharge
streams at persons. This product is to
be used only by trained operators.
ALWAYS remove lance from gun before
cleaning debris from tip.
• Keep clear of nozzle. NEVER direct high pressure
spray at a person, animal, or yourself.
• ALWAYS wear safety glasses or
goggles and protective equipment
(hearing protection, gloves, rubber
boots, protective clothing) when
operating or performing
maintenance.
• NEVER put hand or fingers over the spray tip
while operating the unit.
• NEVER try to stop or deflect leaks with any body
part.
• ALWAYS engage the trigger safety latch in the
safe position when spraying is stopped even if
only for a few moments.
• ALWAYS follow detergent manufacturer’s label
recommendations for proper use of detergents.
ALWAYS protect eyes, skin, and respiratory
system from detergent use.
DO NOT use
pressure that
exceeds the operating pressure of any
of the parts (hoses, fittings, etc.) in
the pressurized system. Ensure all
equipment and accessories are rated
to withstand the maximum working
pressure of the unit.
Explosion hazard.
• NEVER spray flammable liquids or use pressure
washer in areas containing combustible dust,
liquids, or vapors.
• NEVER operate this machine in a closed building
or in or near an explosive environment.
• DO NOT remove fuel tank cap or fill fuel tank
while engine is hot or running (allow engine to
cool two minutes before refueling). ALWAYS fill
the tank slowly.
• NEVER disconnect the high pressure discharge
hose from the machine while the system is
pressurized. To depressurize machine, turn
power and water supply off, then press the gun
trigger 2-3 times.
• NEVER permanently engage the trigger
mechanism on the gun.
• NEVER operate the machine without all
components properly connected to the machine
(handle, gun/wand assembly, nozzle, etc.).
Keep hose away from sharp
objects. Bursting hoses may
cause injury. Examine hoses regularly and replace if
damaged. DO NOT attempt to mend a damaged
hose.
Equipment damage.
• ALWAYS turn water supply “ON” before turning
pressure washer “ON.” Running pump dry causes
serious damage.
• DO NOT operate the pressure washer with the
inlet water screen removed. Keep screen clear of
debris and sediment.
• NEVER operate pressure washer with broken or
missing parts. Check equipment regularly and
repair or replace worn or damaged parts
immediately.
NOTICE
!
CAUTION
!
WARNING
!
WARNING
!
WARNING
!
WARNING
!
WARNING
English — 7
SAFETY GUIDELINES
• Use only the nozzle supplied with this machine.
• NEVER leave the wand unattended while the
machine is running.
• NEVER tamper with the engine governor or
attempt to alter factory settings. Altering factory
settings could damage the unit and will void the
warranty.
• ALWAYS hold gun and wand firmly when
starting and operating the machine.
• NEVER allow the unit to run with the trigger
released (off) for more than two minutes.
Resulting heat buildup will damage the pump.
• NEVER store the pressure washer outdoors or
where it could freeze. Freezing temperatures can
seriously damage the pump.
• Release the trigger when changing from high to
low pressure modes. Failure to do so could result
in damage to the nozzle.
8 — English
2. On models 5525W and 6026W connect clear plastic
hose to hose barb on detergent tank (See Figure 2).
On models 1335PW and 9030PW connect to brass
barb on pump (See Figure 3).
3. Secure garden hose (not included) to the inlet
connection on pump (See Figures 4 and 5).
PRE-OPERATION
UNPACKING
Remove the equipment and all parts from the
carton. The carton should contain the following.
• One pressure washer (pump, engine, cart base).
• One cart handle assembly.
• One spray gun.
• One lance.
• Two spray tips for Model 5525PW
Five spray tips for Models 1335PW, 6026PW and
9030PW
• One high pressure hose.
• One pack of nuts, bolts, and manuals.
• One bottle of engine oil.
If any parts are missing, Please contact your
Husqvarna dealer.
After unpacking the product, inspect it carefully for
any damage that may have occurred during transit.
Make sure to tighten fittings and bolts before using
the pressure washer.
DO NOT operate the unit if it’s
damaged during shipping,
handling, or use. Damage could result in bursting
and cause injury or property damage.
ASSEMBLY
Use 1/2” (13 mm) wrench to assemble pressure
washer. On model 5525PW use two adjustable or
7/16” wrenches.
1. Slide the handle assembly over the lower legs of
the cart base. Use the standard nut and bolt to
secure the legs. See Figure 1.
Figure 1 - Assemble Handle
Figure 3 - Connect detergent hose to brass barb
Figure 2 - Connect detergent hose to detergent tank
Figure 4 - Secure garden hose
Garden Hose
High Pressure
Hose
!
WARNING
Loading...