Page 1
7021R
Operator’s Manual
532 43 10-24 12.07.09 BY Printed in U.S.A.
Page 2
SAFETY RULES
Safe Operation Practices for Walk-Behind Mowers
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE
TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
Look for this symbol to point out im por tant safety precautions. It means
CAUTION!!! BE COME ALERT!!! YOUR
SAFE TY IS IN VOLVED.
CAUTION: Always disconnect spark plug
wire and place wire where it cannot contact
spark plug in order to prevent ac ci den tal
starting when setting up, trans port ing,
adjusting or making re pairs.
WARNING: Engine exhaust, some of its
con stit u ents, and certain vehicle com po nents contain or emit chem i cals known to
the State of Cal i for nia to cause can cer and
birth defects or oth er re pro duc tive harm.
WARNING: Battery posts, terminals and
related ac ces so ries contain lead and lead
compounds, chemicals known to the State
of Cal i for nia to cause can cer and birth
defects or oth er re pro duc tive harm. Wash
hands after handling.
CAUTION: Muffl er and other engine parts
become extremely hot during operation
and remain hot after engine has stopped.
To avoid severe burns on contact, stay away
from these areas.
I. GENERAL OPERATION
• Read, understand, and follow all instructions on the
machine and in the manual(s) before starting. Be thor ough ly familiar with the controls and the proper use of
the machine before starting.
• Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
• Only allow responsible individuals, who are familiar
with the instructions, to operate the machine.
• Clear the area of objects such as rocks, toys, wire,
bones, sticks, etc., which could be picked up and thrown
by the blade.
• Be sure the area is clear of other people before mow ing. Stop machine if anyone enters the area.
• Do not operate the mower when barefoot or wearing
open sandals. Always wear substantial foot wear.
• Do not pull mower backwards unless absolutely nec es sary. Always look down and behind before and while
moving backwards.
• Never direct discharged material toward anyone.
Avoid discharging material against a wall or obstruction. Material may richochet back toward the operator.
Stop the blade when crossing gravel surfaces.
• Do not operate the mower without proper guards,
plates, grass catcher or other safety protective devices
in place.
• See manufacturer’s instructions for proper operation
and installation of accessories. Only use accessories
approved by the manufacturer.
• Stop the blade(s) when crossing gravel drives, walks,
or roads.
• Stop the engine (motor) whenever you leave the equip ment, before cleaning the mower or unclogging the
chute.
• Shut the engine (motor) off and wait until the blade comes
to complete stop before removing grass catch er.
• Mow only in daylight or good artifi cial light.
• Do not operate the machine while under the infl uence
of alcohol or drugs.
• Never operate machine in wet grass. Always be sure of
your footing: keep a fi rm hold on the handle and walk;
never run.
• Disengage the self-propelled mechanism or drive clutch
on mowers so equipped before starting the engine (motor).
• If the equipment should start to vibrate abnormally,
stop the engine (motor) and check immediately for the
cause. Vibration is generally a warning of trouble.
• Always wear safety goggles or safety glasses with side
shields when operating mower.
II. SLOPE OPERATION
Slopes are a major factor related to slip and fall accidents
which can result in severe injury. All slopes require extra
caution. If you feel uneasy on a slope, do not mow it.
DO:
• Mow across the face of slopes: never up and down. Exercise extreme caution when changing direction on slopes.
• Remove obstacles such as rocks, tree limbs, etc.
• Watch for holes, ruts, or bumps. Tall grass can hide
obstacles.
DO NOT:
• Do not trim near drop-offs, ditches or embankments.
The operator could lose footing or balance.
• Do not trim excessively steep slopes.
• Do not mow on wet grass. Reduced footing could cause
slipping.
III. CHILDREN
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
Never
the machine and the mowing activity.
assume that
children will remain where you last saw them.
• Keep children out of the trimming area and under the
watchful care of another re spon si ble adult.
• Be alert and turn machine off if children enter the
area.
• Before and while walking backwards, look behind and
down
for small children.
• Never allow children to operate the machine.
• Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
IV. SAFE HANDLING OF GASOLINE
Use extreme care in handling gasoline. Gasoline is extremely fl ammable and the vapors are explosive.
• Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
• Use only an approved container.
• Never remove gas cap or add fuel with the engine run-
2
ning. Allow engine to cool before refueling.
Page 3
• Never refuel the machine indoors.
• Never store the machine or fuel container where there
is an open fl ame, spark or pilot light such as a water
heater or on other appliances.
• Never fi ll containers inside a vehicle, on a truck or trailer
bed with a plastic liner. Always place containers on
the ground away from your vehicle before fi lling.
• Remove gas-powered equipment from the truck or trailer
and refuel it on the ground. If this is not possible, then
refuel such equipment with a portable container, rather
than from a gasoline dispenser nozzle.
• Keep the nozzle in contact with the rim of the fuel tank
or container opening at all times until fueling is complete.
Do not use a nozzle lock-open device.
• If fuel is spilled on clothing, change clothing immediately.
• Never overfi ll fuel tank. Replace gas cap and tighten
securely.
V. GENERAL SERVICE
• Never run a machine inside a closed area.
• Never make adjustments or repairs with the engine
(motor) running. Disconnect spark plug wire, and keep
WARNING: This lawn mower is equipped with an internal com bus tion engine and should not be used on or near any
un im proved forest-covered, brush-covered or grass-cov ered land unless the engine’s exhaust system is equipped with
a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in
effective working order by the operator.
A spark arrester for the muffl er is available through your nearest authorized service center.
wire away from plug to prevent accidental starting.
• Keep nuts and bolts, especially blade attachement
bolts, tight and keep equipment in good condition.
• Never tamper with safety devices. Check their proper
operation regularly.
• Keep machine free of grass, leaves, or other debris
build-up. Clean oil or fuel spillage. Allow machine to
cool before storing.
• Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
• Never attempt to make wheel height adjustments while
the engine (motor) is running.
• Grass catcher components are subject to wear, dam age, and deterioration, which could expose moving
parts or allow objects to be thrown. Frequently check
com po nents and replace with manufacturer’s rec om mend ed parts, when necessary.
• Mower blade is sharp and can cut. Wrap the blade or
wear gloves, and use extra caution when servicing it.
• Do not change the engine governor setting or overspeed
the engine.
• Maintain or replace safety and instruction labels, as
necessary.
CONGRATULATIONS on your purchase of a new lawn
mower. It has been designed, engineered and man u fac tured
to give you the best possible dependability and performance.
Should you experience any problem you cannot easily
remedy, please contact your nearest authorized service
center/department. We have competent, well-trained
tech ni cians and the proper tools to service or repair this
lawn mower.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your lawn mower
properly. Always observe the “SAFETY RULES”.
SERIAL
NUMBER: _________________________________
DATE OF PURCHASE: _______________________
THE MODEL AND SERIAL NUMBERS WILL BE FOUND
ON A DECAL ATTACHED TO THE REAR OF THE LAWN
MOWER HOUSING.
YOU SHOULD RECORD BOTH SERIAL NUMBER AND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
PRODUCT SPECIFICATIONS
Gasoline Capacity 1.0 Quarts
and Type: (Unleaded Regular Only)
Oil Type (API SG–SL): SAE 30 (above 0°C / 32°F)
SAE 10W-30 (below 0°C / 32°F)
Oil Capacity: 18.5 Ounces
Spark Plug: NGK BPR6ES (Gap: .030")
Valve Clearance: Intake: 0.015 mm
(± 0.04 mm) Exhaust: 0.020 mm
Blade Bolt Torque: 35-40 ft. lbs.
CUSTOMER RESPONSIBILITIES
• Read and observe the safety rules.
• Follow a regular schedule in maintaining, caring for
and using your lawn mower.
• Follow the instructions under “Maintenance” and “Stor age” sec tions of this own er’s manual.
TABLE OF CONTENTS
SAFETY RULES .........................................................2-3
PRODUCT SPECIFICATIONS....................................... 3
CUSTOMER RESPONSIBILITIES................................. 3
ASSEMBLY.................................................................... 4
OPERATION ...............................................................5-9
MAINTENANCE SCHEDULE ...................................... 10
MAINTENANCE...................................................... 10-12
SERVICE AND AD JUST MENTS ............................13-14
STORAGE............................................................... 14-15
TROU BLE SHOOT ING ................................................. 16
WARRANTY................................................................. 18
3
Page 4
ASSEMBLY
Read these instructions and this man u al in its entirety before you attempt to assemble or operate your new lawn mow er.
IMPORTANT: THIS LAWN MOWER IS SHIPPED WITH OUT OIL OR GASOLINE IN THE ENGINE.
Your new lawn mower has been as sem bled at the factory with the ex cep tion of those parts left unassembled for shipping
purposes. All parts such as nuts, washers, bolts, etc., necessary to com plete the as sem bly have been placed in the parts
bag. To ensure safe and proper operation of your lawn mow er, all parts and hard ware you assemble must be tightened
se cure ly. Use the correct tools as nec es sary to ensure proper tightness.
TO RE MOVE LAWN MOW ER FROM CAR TON
1. Remove loose parts included with mower.
2. Cut down two end corners of car ton and lay end panel
down fl at.
3. Remove all packing materials ex cept padding be tween
upper and lower handle and padding holding operator
presence control bar to up per handle.
4. Roll lawn mower out of carton and check carton thorougly for ad di tion al loose parts.
HOW TO SET UP YOUR LAWN MOW ER
TO UNFOLD HANDLE (See Figs. 1 and 2)
IMPORTANT: UNFOLD HANDLE CAREFULLY SO AS
NOT TO PINCH OR DAMAGE CON TROL CABLES.
1. Raise lower handle section to operating position and
squeeze the bottom ends of lower handle towards
each other until the pin in handle can be inserted into
one of the three height adjustment holes.
2. Remove protective padding, raise upper handle sec tion into place on lower handle and tighten both handle
knobs.
3. Remove any packing material from around control bar.
Your handles may be adjusted for your mowing comfort.
Refer to “ADJUST HANDLE” in the Service and Ad just ments
sec tion of this man u al.
OPERATOR
PRESENCE
CONTROL
BAR
LIFT
UP
MOWING
PO SI TION
SQUEEZE
FIG. 2
TO ASSEMBLE GRASS CATCHER
(See Fig. 3)
1. Put grass catcher frame into grass bag with rigid part
of bag on the bottom. Make sure the frame handle is
outside of the bag top.
2. Slip vinyl bindings over frame.
NOTE: If vinyl bindings are too stiff, hold them in warm water
for a few minutes. If bag gets wet, let it dry before using.
HAN DLE PIN
HANDLE
BRACKET
FRAME
HANDLE
LIFT
UP
FIG. 1
UPPER
HANDLE
HANDLE
KNOB
LOWER
HANDLE
VINYL
BINDINGS
OPENING
FIG. 3
TO INSTALL ATTACHMENTS
Your lawn mower was shipped ready to be used as a
mulcher. To convert mower to bagging or discharging,
see “TO CON VERT MOWER” in the Operation section of
this man u al.
4
FRAME
Page 5
OPERATION
KNOW YOUR LAWN MOWER
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER.
Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments.
Save this manual for future reference.
These symbols may appear on your lawn mower or in literature supplied with the product. Learn and understand
their meaning.
DRIVE CONTROL LEVERS
STARTER
HANDLE
GRASS
CATCHER
MULCHER
PLUG
SINGLE POINT HEIGHT ADJUSTER
HANDLE
OPERATOR PRESENCE CON TROL BAR
HANDLE KNOB
DRIVE COVER
GAS O LINE FILL ER CAP
FUEL VALVE LEVER
AIR FILTER
EN GINE OIL CAP WITH DIPSTICK
MUFFLER
IMPORTANT: This lawn mower is shipped
MULCHER DOOR
SPARK PLUG
HOUSING
WITHOUT OIL OR GASOLINE in the engine.
MEETS CPSC SAFETY REQUIREMENTS
Our rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute
and the U.S. Consumer Product Safety Commission. WARNING: The blade turns when the engine is running.
OPERATOR PRESENCE CONTROL BAR – must be held
down to the handle to start the engine. Release to stop
the engine.
STARTER HANDLE – used for starting the engine.
DRIVE CONTROL LEVERS – used to engage power-pro-
pelled forward motion lawn mower.
SINGLE POINT HEIGHT ADJUSTER – used to adjust
cutting height of lawn mower.
MULCHER DOOR – allows conversion to discharge or
bagging operation.
MULCHER PLUG – located at the discharge opening, must
be removed when converting to bagging operation.
5
Page 6
OPERATION
The operation of any lawn mower can result in foreign objects thrown into the eyes, which can result in
severe eye damage. Always wear safety glasses or eye shields while operating your lawn mower or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask
over spectacles.
HOW TO USE YOUR LAWN MOWER
ENGINE SPEED
The engine speed was set at the factory for optimum performance. Speed is not adjustable.
ENGINE ZONE CONTROL
CAUTION: Federal regulations require
an engine control to be installed on this
lawn mower in order to minimize the risk
of blade contact injury. Do not un der
any cir cum stanc es attempt to defeat
the function of the operator control. The
blade turns when the engine is running.
• Your lawn mower is equipped with an operator presence
control bar which requires the operator to be positioned
behind the mower handle to start and operate the mower.
DRIVE CONTROL (See Fig. 4)
• Self-propelling is controlled by hold ing the operator
presence control bar down to the handle and pulling
either drive control lever rearward to the handle. The
further toward the handle a lever is pulled, the faster
the unit will travel.
• Forward motion will stop when either the operator presence control bar or a drive control lever are released. To
stop forward motion without stop ping engine, re lease a
drive control lever only. Hold op er a tor presence control
bar down against handle to con tin ue mowing without
self-propelling.
NOTE: If after releasing the drive control the mower will
not roll backwards, push the mower forward slightly to
disengage drive wheels.
OPERATOR PRESENCE CONTROL BAR
2. Rotate turnbuckle on drive control to increase drive
speed.
3. Operate mower to test drive speed. Readjust as required.
4. If condition fails to improve after the above steps (forward speed remains the same), your drive belt is worn
and should be re placed.
ADJUSTMENT TURNBUCKLE
FIG. 5
TO ADJUST CUTTING HEIGHT (See Fig. 6)
All four wheels are adjusted by a single lever.
• Pull adjuster lever toward wheel. To raise mower, move
lever forward to desired position. To lower mower, move
the lever toward the rear.
LEVER BACKWARD
TO LOWER MOWER
WHEEL
AD JUST ER
LEVER
DRIVE
CONTROL
LEVERS
TO ENGAGE
DRIVE CONTROL
DRIVE CONTROL
DISENGAGED
FIG. 4
DRIVE CONTROL ADJUSTMENT (See Fig. 5)
Over time, the drive control system may become “loose”,
resulting in decreased speed. There is a turnbuckle on
the drive control housing to increase tension on the drive
cable. Pro ceed as follows:
1. Turn unit off and disconnect spark plug wire from spark
plug.
LEVER FORWARD
TO RAISE MOWER
FIG. 6
6
Page 7
OPERATION
TO ATTACH GRASS CATCHER (See Fig. 7)
1. Lift the rear door of the lawn mower and place the grass
catcher frame side hooks onto the door pivot pins.
2. The grass catcher is secured to the lawn mower hous ing
when the rear door is lowered onto the grass catcher
frame.
CAUTION: Do not run your lawn mower
without mulcher plug or ap proved grass
catch er in place. Nev er at tempt to op er ate the lawn mower with the rear door
re moved or propped open.
PIVOT PINS
REAR DOOR
GRASS
CATCHER
HANDLE
TO CONVERT MOWER
Your lawn mower was shipped ready to be used as a
mulcher. To convert to bagging or discharging:
REAR BAGGING (See Fig. 9)
• Open rear door and remove mulcher plug. Store
mulcher plug in a safe place.
• You can now install the grass catcher.
• To convert to mulching or discharging operation, install
mulcher plug into rear discharge opening of mower.
MULCHER PLUG
FIG. 9
CATCHER FRAME HOOK
FIG. 7
TO EMPTY GRASS CATCHER (See Fig. 8)
1. Lift up on grass catcher using the frame han dle.
2. Remove grass catcher with clippings from under lawn
mower han dle.
3. Empty clippings from bag.
NOTE: Do not drag the bag when emptying; it will cause
unnecessary wear.
FRAME
HANDLE
SIDE DIS CHARG ING (See Fig. 10)
• Mulcher plug must be installed into rear discharge
open ing of mower.
• Open mulcher door and install discharge defl ector
un der door as shown.
• Mower is now ready for discharging operation.
• To convert to mulching or bagging operation, dis charge
defl ector must be removed and mulcher door closed.
SIMPLE STEPS TO REMEMBER
WHEN CONVERTING YOUR LAWN MOWER
FOR MULCHING -
1. Rear mulcher plug installed.
2. Mulcher door closed.
FOR REAR BAGGING -
1. Rear mulcher plug removed.
2. Grass catcher installed.
3. Mulcher door closed.
FOR SIDE DISCHARGING -
1. Rear mulcher plug installed.
2. Discharge defl ector installed.
CAUTION: Do not run your lawn mower
without mulcher plug or ap proved grass
catch er in place. Nev er at tempt to op er ate the lawn mow er with the rear door
re moved or propped open.
FIG. 8
7
Page 8
OPEN MULCHER DOOR
INSTALL
DISCHARGE
DEFLECTOR
OPERATION
BEFORE STARTING ENGINE
ADD OIL (See Fig. 11)
Your lawnmower is shipped without oil in the engine. For type
and grade of oil to use, see “EN GINE” in the Maintenance
section of this manual.
CAUTION: DO NOT overfi ll engine with
oil, or it will smoke heavily from the muffl er on startup.
1. Be sure lawnmower is level.
2. Remove oil fi ll cap / dipstick from oil fi ll spout.
3. Engine holds 18.5 ounces of oil. Pour oil slowly. Do
not overfi ll. Wait one minute to allow oil to settle. Use
gauge on oil fi ll cap/dipstick for checking level. Insert
dipstick into the tube and rest the oil fi ll cap on the
tube. DO NOT thread the cap into the tube when taking reading.
4. Insert and tighten oil fi ll cap / dipstick.
IMPORTANT:
• Check oil level before each use. Add oil if needed. Fill
to full line on dipstick.
• Change the oil after every 25 hours of operation or each
season. You may need to change the oil more often
under dusty, dirty conditions. See “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.
MOWER IS NOW READY FOR
DISCHARGING OPERATION
FIG. 6
OIL FILL CAP/
DIPSTICK
UPPER
MARK
LOWER
MARK
GASOLINE
FILLER CAP
FIG. 11
8
Page 9
OPERATION
ADD GASOLINE (See Fig. 11)
• Fill fuel tank to bottom of tank fi ller neck. Do not overfi ll. Use fresh, clean, regular unleaded gasoline with
a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quan ti ties that can be used within 30
days to assure fuel freshness.
CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open fl ame.
Alcohol blended fuels (called gasohol
or using ethanol or methanol) can attract moisture which leads to separation
and for ma tion of acids during storage.
Acidic gas can damage the fuel system of an engine while in storage. To
avoid engine problems, the fuel system
should be emptied before stor age of
30 days or longer. Empty the gas tank,
start the engine and let it run until the
fuel lines and carburetor are empty. Use
fresh fuel next season. See Storage
In struc tions for additional information.
Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
TO STOP ENGINE
• To stop engine, release operator presence control bar.
Wait until blade and all moving parts have stopped and
turn fuel valve to OFF position if you do not intend to
re start the engine soon.
TO START ENGINE (See Fig. 12)
NOTE: Due to protective coatings on the engine, a small
amount of smoke may be present during the initial use of
the product and should be considered normal.
1. Be sure fuel valve is in the ON po si tion.
2. Move choke lever to ON ( ) position.
3. Hold operator presence control bar down to the han dle
and pull starter handle quickly. Do not allow starter rope
to snap back.
NOTE: The choke lever automatically begins moving to
the OFF position when operator presence control bar is
held down to handle.
OFF
CHOKE LEVER
MOWING TIPS
CAUTION: Do not use de-thatcher blade
attachments on your mower. Such attachments are hazardous, will damage
your mower and could void your warranty.
• Under certain conditions, such as very tall grass, it
may be necessary to raise the height of cut to reduce
pushing effort and to keep from overloading the engine
and leaving clumps of grass clippings. It may also be
necessary to reduce ground speed and/or run the lawn
mower over the area a second time.
• For extremely heavy cutting, reduce the width of cut
by overlapping previously cut path and mow slowly.
• For better grass bagging and most cutting conditions,
the engine speed should be set in the fast position.
• Pores in cloth grass catchers can become fi lled with
dirt and dust with use and catchers will collect less
grass. To prevent this, regularly hose catcher off with
water and let dry before using.
• Keep top of engine around starter clear and clean of
grass clippings and chaff. This will help engine air fl ow
and extend engine life.
MULCHING MOWING TIPS
IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER
HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE
“CLEANING” IN THE MAINTENANCE SECTION OF THIS MANUAL.
• The special mulching blade will recut the grass clippings many times and reduce them in size so that as
they fall onto the lawn they will disperse into the grass
and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always
mulch with your highest engine (blade) speed as this
will provide the best recutting action of the blades.
• Avoid cutting your lawn when it is wet. Wet grass tends
to form clumps and interferes with the mulching action.
The best time to mow your lawn is the early afternoon.
At this time the grass has dried, yet the newly cut area
will not be exposed to direct sunlight.
• For best results, adjust the lawn mower cutting height
so that the lawn mower cuts off only the top one-third
of the grass blades (See Fig. 13). If the lawn is overgrown it will be necessary to raise the height of cut to
reduce pushing effort and to keep from overloading
the engine and leaving clumps of mulched grass. For
extremely heavy mulching, reduce your width of cut by
overlapping previously cut path and mow slowly.
ON
( )
ON
FUEL VALVE LEVER
FIG. 12
OFF
MAX 1/3
FIG. 13
• Certain types of grass and grass conditions may require
that an area be mulched a second time to completely
hide the clippings. When doing a second cut, mow
across (perpendicular) to the fi rst cut path.
• Change your cutting pattern from week to week. Mow
north to south one week then east to west the next week.
9
This will help prevent matting and graining of the lawn.
Page 10
MAINTENANCE
Check for Loose Fasteners
Clean / Inspect Grass Catcher *
Check Tires
Check Drive Wheels ***
Clean Lawn Mower ****
Clean under Drive Cover ***
Check Drive Belt / Pulleys ***
Check / Sharpen / Replace Blade
Lubrication
Clean and Recharge Battery **
Check Engine Oil level
Change Engine Oil
Clean Air Filter
Inspect Muffler
Replace Spark Plug
Replace Air Filter Paper Cartridge
Empty fuel system or add Stabilizer
BEFORE
EACH
USE
AFTER
EACH
USE
EVERY
10
HOURS
EVERY
25 HOURS
OR SEASON
EVERY
100
HOURS
BEFORE
STORAGE
(if so equipped)
*
Electric-Start mowers
**
Power-Propelled mowers
***
Use a scraper
****
to clean under deck
The warranty on this lawn mower does not cover items that
have been subjected to operator abuse or negligence. To
receive full value from the warranty, operator must maintain
mower as instructed in this manual. Some adjustments
will need to be made periodically to properly maintain your
unit. At least once a season, check to see if you should
make any of the adjustments described in the Service and
Ad just ments section of this manual.
• At least once a year, replace the spark plug, clean or
replace air fi lter element and check blade for wear. A
new spark plug and clean/new air fi lter element assure
proper air-fuel mixture and help your engine run better
and last longer.
• Follow the maintenance schedule in this manual.
1 - Change more often if operating under a heavy load or in high outdoor temperatures.
2 - Service more often if operating in dirty or dusty conditions.
3 - Replace blades more often when mowing in sandy soil.
4 - Charge 48 hours at end of season.
5 - And after each 5 hours of use.
BEFORE EACH USE
1. Check engine oil level.
2. Check for loose fasteners.
LUBRICATION CHARTGENERAL RECOMMENDATIONS
ENGINE OIL
➁
MULCHER
➀
DOOR
HINGE PIN
REAR DOOR HINGE
➀
LUBRICATION
Keep unit well lubricated (See “LUBRICATION CHART”).
IMPORTANT: DO NOT OIL OR GREASE PLASTIC WHEEL
BEARINGS. VISCOUS LU BRI CANTS WILL ATTRACT DUST
AND DIRT THAT WILL SHORT EN THE LIFE OF THE SELFLU BRI CAT ING BEARINGS. IF YOU FEEL THEY MUST BE
LU BRI CATED, USE ONLY A DRY, POW DERED GRAPHITE
TYPE LUBRICANT SPAR INGLY.
10
HANDLE BRACK ET MOUNT ING PINS
➀
SPRAY LUBRICANT
➀
SEE “ENGINE” IN MAINTENANCE SECTION
➁
Page 11
MAINTENANCE
LAWN MOWER
Always observe safety rules when performing any main te nance.
TIRES
• Keep tires free of gasoline, oil, or insect control chem i cals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
DRIVE WHEELS
Check rear drive wheels each time you mow to be sure they
move freely. The wheels not turning freely means trash,
grass cuttings, etc., may be inside the drive wheel and dust
cover area and must be cleaned out to free drive wheels.
If necessary to clean drive wheels, check both rear wheels.
BLADE CARE
For best results, mower blade must be kept sharp. Re place
bent or dam aged blades.
CAUTION: Use only a replacement blade
approved by the manufacturer of your
mower. Using a blade not approved
by the manufacturer of your mower is
hazardous, could damage your mower
and void your warranty.
TO REMOVE BLADE (See Fig. 14)
1. Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
2. Turn lawn mower on its side. Make sure air fi lter and
carburetor are up.
3. Use a wood block between blade and mower hous ing
to prevent blade from turning when re mov ing blade bolt.
NOTE: Protect your hands with gloves and/or wrap blade
with heavy cloth.
4. Remove blade bolt by turning counter-clockwise.
5. Remove blade and attaching hardware (bolt, lock wash er
and hardened wash er).
NOTE: Remove the blade adapter and check the key inside
hub of blade adapter. The key must be in good condition to
work properly. Replace adapter if dam aged.
TO REPLACE BLADE (See Fig. 14)
1. Position the blade adapter on the engine crank shaft. Be
sure key in adapter and crankshaft key way are aligned.
2. Position blade on the blade adapter aligning the two
(2) holes in the blade with the raised lugs on the
adapter.
3. Be sure the trailing edge of blade (opposite sharp edge)
is up toward the engine.
4. Install the blade bolt with the lock washer and hard ened
washer into blade adapter and crank shaft.
5. Use block of wood between blade and lawn mower
housing and tighten the blade bolt, turning clock wise.
• The recommended tightening torque is 35-40 ft. lbs.
IMPORTANT: BLADE BOLT IS HEAT TREATED. IF BOLT NEEDS
REPLACING, REPLACE ONLY WITH APPROVED BOLT SHOWN
IN THE REPAIR PARTS SECTION OF THIS MANUAL.
BLADE ADAPTER KEY
BLADE
LOCK
WASHER
BLADE
BOLT
TO SHARPEN BLADE
NOTE: We do not recommend sharp en ing blade - but if
you do, be sure the blade is balanced.
Care should be taken to keep the blade balanced. An
un bal anced blade will cause eventual damage to lawn
mower or engine.
• The blade can be sharp ened with a fi le or on a grinding
• To check blade balance, drive a nail into a beam or
HARDENED
WASHER
TRAILING EDGE
wheel. Do not attempt to sharpen while on the mower.
wall. Leave about one inch of the straight nail ex posed.
Place center hole of blade over the head of the nail.
If blade is balanced, it should remain in a horizontal
position. If either end of the blade moves downward,
sharpen the heavy end until the blade is balanced.
CRANKSHAFT
FIG. 14
CRANKSHAFT
KEY WAY
RETAINER
GRASS CATCHER
• The grass catcher may be hosed with water, but must
be dry when used.
• Check your grass catcher often for damage or de te ri o ra tion. Through normal use it will wear. If catcher
needs replacing, replace only with ap proved replacement catcher shown in the Repair Parts section of this
manual. Give the lawn mower model number when
ordering.
GEAR CASE
• To keep your drive system working properly, the gear
case and area around the drive should be kept clean
and free of trash build-up. Clean under the drive cover
twice a season.
• The gear case is fi lled with lubricant to the proper
level at the factory. The only time the lubricant needs
attention is if service has been performed on the gear
case.
• If lubricant is required, use only Texaco Starplex Pre mi um 1 Grease, Part No. 750369. Do not substitute.
ENGINE
Maintenance, re pair, or re place ment of the emission con trol de vic es and sys tems, which are be ing done at the
cus tom ers expense, may be performed by any non-road
engine repair es tab lish ment or individual. Warranty repairs
must be performed by an authorized engine man u fac tur er's
service outlet.
11
BELT
Page 12
MAINTENANCE
LUBRICATION
Use only high quality detergent oil rated with API service
classifi cation SG–SL. Select the oil's SAE viscosity grade
according to your expected operating temperature.
NOTE: Multi-viscosity oils (5W30, 10W30 etc.) improve
starting in cold weather, and you should check your engine
oil level frequently to avoid possible engine damage from
running low on oil.
Change the oil after every 25 hours of operation or at least
once a year if the lawn mower is not used for 25 hours in
one year.
Check the crankcase oil level before starting the engine
and after each fi ve (5) hours of continuous use. Tighten oil
plug securely each time you check the oil level.
TO CHANGE ENGINE OIL (See Figs. 15 & 16)
NOTE: Before tipping lawn mower to drain oil, empty fuel
tank by running engine until fuel tank is empty.
1. Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
2. Remove engine oil cap; lay aside on a clean surface.
3. Tip lawn mower on its side as shown and drain oil into
a suitable container. Rock lawn mower back and forth
to remove any oil trapped inside of engine.
7. Continue adding small amounts of oil and rechecking
the dipstick until it reads full. DO NOT overfi ll, or engine
will smoke on startup.
8. Always be sure retighten dipstick before starting engine.
9. Re con nect spark plug wire to spark plug.
OIL FILL CAP /
DIPSTICK
UPPER
MARK
LOWER
MARK
FIG. 16
AIR FILTER
Your engine will not run properly and may be damaged
by using a dirty air fi lter. Replace the air fi lter every 100
hours of operation or every season, whichever occurs fi rst.
Ser vice air cleaner more often under dusty conditions. See
the main te nance section of your engine manual.
MUFFLER
Inspect and replace corroded muffl er as it could create a
fi re hazard and/or damage.
SPARK PLUG
Replace spark plug at the beginning of each mowing season
or after every 100 hours of operation, whichever occurs
fi rst. Spark plug type and gap setting are shown in the
“PROD UCT SPEC I FI CA TIONS” section of this manual.
CONTAINER
FIG. 15
4. Wipe off any spilled oil from mower or side of engine.
5. Fill engine with oil. The engine oil capacity is 18.5 oz.
If oil is not com plete ly drained from engine, you may
not need the entire container of a 20 oz. bottle of oil.
Slowly pour 3/4 of the oil from the container down the
oil fi ll spout into the engine.
6. Wait one minute to allow oil to settle. Use guage on oil
fi ll cap/dipstick for checking level. Insert dipstick into
the tube and rest the oil fi ll cap on the tube. DO NOT
thread the cap into the tube when taking reading.
CLEANING
IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER
HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN
THE UNDERSIDE OF YOUR MOWER AFTER EACH USE.
CAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with plug.
• Clean the underside of your lawn mower by scraping
to remove build-up of grass and trash.
• Clean engine often to keep trash from accumulating. A
clogged engine runs hotter and shortens engine life.
• Keep fi nished surfaces / wheels free of gasoline, oil, etc.
• We do not recommend using a garden hose to clean
lawn mower unless the electrical system, muffl er, air
fi lter and carburetor are covered to keep water out.
Water in engine can result in shortened engine life.
CLEAN UNDER DRIVE COVER
Clean under drive cover at least twice a season. Scrape underside of cover with putty knife or similar tool to remove any
build-up of trash or grass on underside of drive cover.
12
Page 13
SERVICE AND ADJUSTMENTS
CAUTION: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:
1. Release control bar and stop engine.
2. Make sure the blade and all moving parts have completely stopped.
3. Disconnect spark plug wire from spark plug and place where it cannot come in contact with plug.
LAWN MOWER
TO ADJUST CUTTING HEIGHT
See “TO ADJUST CUTTING HEIGHT” in the Operation
section of this manual.
REAR DEFLECTOR
The rear defl ector, attached between the rear wheels of
your mower, is provided to minimize the possibility that
objects will be thrown out of the rear of the mower into
the operator's mowing position. If the defl ector becomes
damaged, it should be replaced.
TO REMOVE DRIVE BELT (See Fig. 17 & 18)
1. Remove drive cover.
2. Remove spring and belt keeper.
3. Remove belt from gearcase pulley.
4. Turn lawn mower on its side with air fi lter and car bu re tor down.
5. Remove blade and blade adapter.
6. Remove belt from blade adapter.
TO REPLACE DRIVE BELT
7. Position the blade adapter on the engine crank shaft.
Be sure key in adapter and crankshaft keyway are
aligned; and that the drive belt is inside the tabs of the
belt retainer.
8. Route the other end of the new drive belt through hole
in housing.
9. Return mower to upright po si tion.
10. Install new belt on gearcase pulley.
11. Reinstall belt keeper and spring.
12. Reinstall drive cover.
NOTE: Always use factory approved belt to assure proper
fi t and long life.
13. Turn lawn mower on its side with air fi lter and car bu re tor down.
14. Reinstall blade.
BLADE ADAPTER KEY
BLADE
LOCK
WASHER
CRANKSHAFT
KEY WAY
GEARCASE
PULEY
FIG. 17
DRIVE
COVER
SPRING
BELT
KEEPER
BELT
13
BLADE
BOLT
HARDENED
WASHER
TRAILING EDGE
CRANKSHAFT
FIG. 18
BELT
RETAINER
Page 14
SERVICE AND ADJUSTMENTS
TO ADJUST HANDLE (See Fig. 19)
The handle on your lawn mower has three (3) height positions - adjust to height that suits you.
• Squeeze the bottom ends of lower handle towards each
other until the pin in handle can be inserted into one
of the three height adjustment holes.
HANDLE PIN
SQUEEZE
HIGH
HANDLE
BRACKET
MED.
LOW
ENGINE
Maintenance, re pair, or re place ment of the emission con trol de vic es and sys tems, which are be ing done at the
cus tom ers expense, may be performed by any non-road
engine repair es tab lish ment or individual. Warranty repairs
must be performed by an authorized engine man u fac tur er's
service outlet.
ENGINE SPEED
Your engine speed has been factory set. Do not attempt to
increase engine speed or it may result in personal injury. If
you believe that the engine is running too fast or too slow,
take your lawn mower to an authorized service center for
repair and adjustment.
CARBURETOR
Your carburetor is not adjustable. If your engine does not
operate properly due to suspected carburetor problems,
take your lawn mower to an authorized service center for
repair and/or adjustment.
IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR,
WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.
OVER SPEED ING THE ENGINE ABOVE THE FACTORY HIGH
SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE
ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING,
CONTACT YOUR NEAREST AUTHORIZED SER VICE CEN TER,
WHICH HAS PROPER EQUIP MENT AND EXPERIENCE TO
MAKE ANY NEC ES SARY ADJUSTMENTS.
FIG. 19
STORAGE
Immediately prepare your mower for storage at the end of the season or if the unit will not be used for 30 days or more.
LAWN MOWER
When lawn mower is to be stored for a period of time, clean
it thoroughly, remove all dirt, grease, leaves, etc. Store in
a clean, dry area.
1. Clean entire lawn mower (See “CLEANING” in the
Maintenance section of this manual).
2. Lubricate as shown in the Maintenance section of this
manual.
3. Be sure that all nuts, bolts, screws, and pins are securely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
4. Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
HANDLE (See Figs. 20 and 21)
You can fold your lawn mower handle for stor age.
1. Loosen the two (2) handle knobs on sides of the upper
handle and allow handle to fold down to the rear.
2. Squeeze the bottom ends of lower handle toward each
other until pins in handle clear the brackets and pivot
entire han dle assembly forward and allow it to rest on
mower.
• When setting up your handle from the storage position,
the lower handle will require manually locking into the
mowing position.
IMPORTANT: WHEN FOLDING THE HANDLE FOR STORAGE
OR TRANSPORTATION, BE SURE TO FOLD THE HANDLE AS
SHOWN OR YOU MAY DAMAGE THE CONTROL CABLES.
14
Page 15
STORAGE
OPERATOR
PRES ENCE
CONTROL
BAR
FOLD
FORWARD
FOR
STORAGE
FIG. 20
MOWING
POSITION
UPPER
HANDLE
HANDLE
KNOB
LOWER
HANDLE
ENGINE
FUEL SYSTEM
IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS
FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS
SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR
TANK DURING STORAGE. ALCOHOL BLENDED FUELS
(CALLED GASOHOL OR USING ETHANOL OR METHANOL)
CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION
AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS
CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN
STORAGE.
• Empty the fuel tank by starting the engine and letting
it run until the fuel lines and carburetor are empty.
• Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during stor age.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of
this manual).
SQUEEZE
HANDLE
BRACKET
FIG. 21
HANDLE PIN
CYLINDER
1. Remove spark plug.
2. Pour one ounce (29 ml) of oil through spark plug hole
into cylinder.
3. Pull starter handle slowly a few times to distribute oil.
4. Replace with new spark plug.
OTHER
• Do not store gasoline from one season to another.
• Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
• If possible, store your unit indoors and cover it to give
protection from dust and dirt.
• Cover your unit with a suitable protective cover that
does not retain moisture. Do not use plastic. Plastic
cannot breathe, which allows condensation to form and
will cause your unit to rust.
IMPORTANT: NEVER COVER MOWER WHILE ENGINE AND
EXHAUST AREAS ARE STILL WARM.
CAUTION: Never store the lawn mower
with gasoline in the tank inside a build ing where fumes may reach an open
fl ame or spark. Allow the engine to cool
before storing in any enclosure.
15
Page 16
TROUBLESHOOTING POINTS
PROBLEM CAUSE CORRECTION
Does not start 1. Dirty air fi lter. 1. Clean/replace air fi lter.
2. Out of fuel. 2. Fill fuel tank.
3. Stale fuel. 3. Empty fuel tank and refi ll tank with fresh,
clean gasoline.
4. Water in fuel. 4. Empty fuel tank and refi ll tank with fresh,
clean gasoline.
5. Spark plug wire is disconnected. 5. Connect wire to plug.
6. Bad spark plug. 6. Replace spark plug.
7. Loose blade or broken blade adapter. 7. Tight en blade bolt or replace blade adapter.
8. Control bar in released position. 8. Depress control bar to handle.
9. Control bar defective. 9. Replace control bar.
10. Fuel valve lever (if equipped) in OFF position. 10. Turn fuel valve lever to the ON position.
11. Weak battery (if equipped). 11. Charge battery.
12. Disconnected battery connector (if equipped). 12. Connect battery to engine.
Loss of power 1. Rear of lawn mower housing or cutting 1. Raise cutting height.
blade dragging in heavy grass.
2. Cutting too much grass. 2. Raise cutting height.
3. Dirty air fi lter. 3. Clean/replace air fi lter.
4. Buildup of grass, leaves and trash under 4. Clean underside of mower housing.
mower.
5. Too much oil in engine. 5. Check oil level.
6. Walking speed too fast. 6. Cut at slower walking speed.
Poor cut – 1. Worn, bent or loose blade. 1. Replace blade. Tighten blade bolt.
uneven 2. Wheel heights uneven. 2. Set all wheels at same height.
3. Buildup of grass, leaves and trash under 3. Clean underside of mower housing.
mower.
Excessive 1. Worn, bent or loose blade. 1. Replace blade. Tighten blade bolt.
vibration 2. Bent engine crankshaft. 2. Contact a qualifi ed service center.
Starter rope 1. Engine fl ywheel brake is on when control 1. Depress control bar to upper handle before
hard to pull bar is released. pulling starter rope.
2. Bent engine crankshaft. 2. Contact a qualifi ed service center.
3. Blade adapter broken. 3. Replace blade adapter.
4. Blade dragging in grass. 4. Move lawn mower to cut grass or other
hard surface before starting.
Grass catcher 1. Cutting height too low. 1. Raise cutting height.
not fi lling 2. Lift on blade worn off. 2. Replace blade.
(if so equipped) 3. Catcher not venting air. 3. Clean grass catcher.
Hard to push 1. Grass is too high or wheel height is too low. 1. Raise cutting height.
2. Rear of lawn mower housing or cutting 2. Raise rear of lawn mower housing one (1)
blade dragging in heavy grass. setting higher.
3. Grass catcher too full. 3. Empty grass catcher.
4. Handle height position not right for you. 4. Adjust handle height to suit.
Loss of drive 1. Belt wear. 1. Check/replace drive belt.
(or slowing of 2. Belt off of pulley. 2. Check/reinstall drive belt.
drive speed) 3. Drive cable worn or broken. 3. Put belt on pulleys / replace belts if broken.
4. “Loose” drive control system. 4. Adjust drive control.
16
Page 17
SERVICE NOTES
17
Page 18
O OBTAIN WARRANTY CONSIDERATION
The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written in the
manufactured by third party engine manufacturer.
(6) Emission Control System components necessary to comply with CARB-TIER II and EPA regulations which are
(5) Commercial or consumer mowing decks with sand abrasion damage.
to the manufacturer,
(4) Lawn and garden attachments are covered by a third party which gives a warranty, all claims for warranty should be sent
starter ropes and tines;
SECTION 4: EXCEPTIONS AND LIMITATIONS
(2) Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction sheet furnished
adverse reaction due to incorrect storage or use habits;
(1) Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any
This warranty shall be inapplicable to defects resulting from the following:
appropriate manufacturer;
warranty as provided in writing with the product information supplied at the time of purchase; all claims must be sent to the
(3) Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective manufacturer’s
(2) Natural discoloration of material due to ultraviolet light;
(4) Additional damage to parts or components due to continued use occurring after any of the above.
safety, or durability, or causes the product to fail to comply with any applicable laws; or:
(3) Alterations or modifications that change the intended use of the product or affects the product’s performance, operation,
by Husqvarna;
PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT TO THE EXTENT
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE
PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR
PREVIOUSLY MANUFACTURED PRODUCTS.
IMPROVE THE DESIGN OF THE PRODUCT WITHOUT NOTICE, AND DOES NOT ASSUME OBLIGATION TO UPDATE
DEFINED IN THE LIMITED WARRANTY STATEMENT. HUSQVARNA RESERVES THE RIGHT TO CHANGE OR
PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO THE WARRANTY PERIOD AS
you may also have other rights which vary from state to state.
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and
Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long an implied
not be used, but delivered as is to an authorized Husqvarna retailer for evaluation. Proof of purchase, as explained in
maintenance section of the Owner’s/Operator’s manual. Should an operational problem or failure occur, the product should
SECTION 5: CUSTOMER RESPONSIBILITIES
It is the Owner’s and Retailer’s responsibility to make certain that the Warranty Registration Card is properly filled out and
section 6, rests solely with the customer.
SECTION 6: PROCEDURE T
Charlotte, NC 28269 Nov 2006
HUSQVARNA
7349 Statesville Road
To obtain the benefit of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna
Proof of purchase must be presented to the authorized Husqvarna retailer in order to obtain warranty service. This proof
must include date purchased, model number, serial number, and complete name and address of the selling retailer.
in order to confirm the warranty and to facilitate post-sale service.
mailed to Husqvarna Forest & Garden Company. This card should be mailed within ten (10) days from the date of purchase
HUSKY62 for a retailer in your area.
Husqvarna retailer can be normally located through the “Yellow Pages” of the local telephone directory or by calling 1-800-
delivered at the owner’s expense. Downtime, pick-up and delivery charges are not covered by this warranty. An authorized
retailer in a timely manner, no later than thirty (30) days from date of the operational problem or failure. The product must be
WARRANTY STATEMENT
5 year consumer warranty or 1,500 hours of use (when used solely at the owner’s residence.)
been limited to the owner’s residence.
nonprofessional, noninstitutional or nonincome producing use, except as herein stated. All consumer product use must have
defects in material and workmanship from the date of purchase for the “Warranty Period” of the product as set forth below:
SECTION 1: LIMITED WARRANTY
Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from
Proof of purchase required.
Lifetime Warranty (Parts and Labor): All tiller tines and trimmer shafts against breakage. Proof of purchase required.
Lifetime Warranty (“PARTS ONLY” after initial warranty expiration): Ignition coils and modules on handheld product.
WARRANTY SCHEDULE FOR TURF CARE Equipment - Zero Turn Riders
(New warranty applies to units sold after August 1, 2005. Also applies to units factory-equipped with R.O.P.S.
EZ Zero Turn Riders: 3 year consumer warranty or 600 hours of use (when used solely at the owner’s residence.)
EZ Zero Turn Riders: 1 year commercial warranty or 600 hours of use.
iZ, LZ & BZ Zero Turn Riders:
warranty. New warranty applies to units sold after August 1, 2005. Also applies to units factory-equipped with R.O.P.S.
Warranty Schedule for Turf Care Walk Behind Units - W, WG & WH Zero Turn Riders - 3 year consumer and commercial
iZ, LZ & BZ Zero Turn Riders: 5 year commercial warranty or 1,500 hours of use.
3 Year or 1,500 Hour Commercial Use Warranty: spindles on zero turn riders, hydraulic pumps and wheel motors.
2 Year COMMERCIAL and CONSUMER Warranty: all Husqvarna ground-engaging commercial equipment.
blowers, backpack blowers, hedge trimmers, electrical products and power-assist collection systems for noncommercial,
noncommercial walk behind mowers, tillers, chain saws, trimmers, brushcutters, clearing saws, snow blowers, handheld
WARRANTY SCHEDULE FOR CONSUMER TURF CARE EQUIPMENT:
2 Year Consumer Warranty: Automatic mower, all Residential Zero Turn Riders, all lawn, yard and garden tractors, all
producing use, except as herein stated. All consumer product use must have been limited to the owner’s residence.
blowers, hedge trimmers, and electrical products for noncommercial, nonprofessional, noninstitutional or nonincome
WARRANTY SCHEDULE FOR CONSUMER FOREST & GARDEN EQUIPMENT:
2 Year Consumer Warranty: all consumer chain saws, trimmers, brushcutters, clearing saws, handheld blowers, backpack
hovering trimmers, stick edgers, backpack blowers, hand held blowers, hedge trimmers, power-assist collection systems for
noninstitutional, non-municipality or non-income producing use. All 300 series trimmers, brushcutters, clearing saws,
2 Year or 2,000 Hour Powertrain & 1 Year or 1,000 Hour Body Warranty: Husqvarna Utility Vehicles.
1 Year Warranty: Power cutters, stump grinder, pole pruners and pole saws for non-commercial, non-professional,
18
Automatic mower, chain saws, 100 series trimmers, power cutters, stump grinders, pole
commercial, institutional, professional or income producing purposes or use.
1 Year Conditional Component Warranty: Chain saw crankshafts for commercial/professional use (parts and labor).Saw
commercial, institutional, professional, municipality or income producing purposes or use except as otherwise provided herein.
saws, pole pruners, snow throwers, model series 580 & 600 walk-behind mowers, or any Husqvarna product used for
must be operated with Husqvarna XP 2 cycle oil.
90 Day Commercial Warranty:
Batteries: 1 year prorated limited warranty with 100% replacement during the first 6 months.
Rental Warranty: 90 days on all applicable professional equipment reference warranty time period charts
care label. The fit of the protective apparel/boot is not covered under warranty.
with a warranty claim form. All care and maintenance instructions must be followed as stated by the manufacturer on the
located in the back of the Retailer Warranty Policy & Procedure Manual.
material and workmanship. Normal wear, tear or abuse is not covered under warranty. Product must be returned to Charlotte
Husqvarna Safety Apparel carries a 90-day warranty from the date of the customer’s original purchase for defects in
warranty with product at time of purchase.
part of engine systems manufactured by third part engine manufacturers for which the purchaser has received a separate
system components necessary to comply with CARB-TIER II and EPA regulations, except for those components which are
30 Day Warranty: Replacement parts, accessories including bars and chains, tools and display items. Emission control
Husqvarna will repair or replace defective components without charge for parts or labor if a component fails because of a
defect in material or workmanship during the warranty period.
SECTION 2: HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY
blades, blade adapters, bulbs, clutches, clutch drums, filters, guide bars, lubricants, rewind springs, saw chain, spark plugs,
(1) Normal customer maintenance items which become worn through normal regular use, including, but not limited to, belts,
SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY
The following items are not covered by this warranty:
Loading...