Page 1
Owner’s Manual
532180311 10.15.01 BY
Printed in U.S.A.
6022SH
Page 2
SAFETY RULES
Safe Operation Practices for Walk-Behind Mowers
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS.
FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
I. GENERAL OPERATION
• Read, understand, and follow all instructions on the machine
and in the manual(s) before starting. Be thoroughly familiar
with the controls and the proper use of the machine before
starting.
• Do not put hands or feet near or under rotating parts. Keep
clear of the discharge opening at all times.
• Only allow responsible individuals, who are familiar with the
instructions, to operate the machine.
• Clear the area of objects such as rocks, toys, wire, bones,
sticks, etc., which could be picked up and thrown by the blade.
• Be sure the area is clear of other people before mowing. Stop
machine if anyone enters the area.
• Do not operate the mower when barefoot or wearing open
sandals. Always wear substantial foot wear.
• Do not pull mower backwards unless absolutely necessary.
Always look down and behind before and while moving
backwards.
• Do not operate the mower without proper guards, plates, grass
catcher or other safety protective devices in place.
• See manufacturer’s instructions for proper operation and
installation of accessories. Only use accessories approved
by the manufacturer.
• Stop the blade(s) when crossing gravel drives, walks, or
roads.
• Stop the engine (motor) whenever you leave the equipment,
before cleaning the mower or unclogging the chute.
• Shut the engine (motor) off and wait until the blade comes to
complete stop before removing grass catcher.
• Mow only in daylight or good artificial light.
• Do not operate the machine while under the influence of
alcohol or drugs.
• Never operate machine in wet grass. Always be sure of your
footing: keep a firm hold on the handle and walk; never run.
• Disengage the self-propelled mechanism or drive clutch on
mowers so equipped before starting the engine (motor).
• If the equipment should start to vibrate abnormally, stop the
engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.
• Always wear safety goggles or safety glasses with side
shields when operating mower.
II. SLOPE OPERATION
Slopes are a major factor related to slip and fall accidents which
can result in severe injury. All slopes require extra caution. If you
feel uneasy on a slope, do not mow it.
DO:
• Mow across the face of slopes: never up and down. Exercise
extreme caution when changing direction on slopes.
• Remove obstacles such as rocks, tree limbs, etc.
• Watch for holes, ruts, or bumps. Tall grass can hide obstacles.
DO NOT:
• Do not trim near drop-offs, ditches or embankments. The
operator could lose footing or balance.
• Do not trim excessively steep slopes.
• Do not mow on wet grass. Reduced footing could cause
slipping.
III. CHILDREN
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the machine
and the mowing activity.
where you last saw them.
• Keep children out of the trimming area and under the watchful
care of another responsible adult.
• Be alert and turn machine off if children enter the area.
• Before and while walking backwards, look behind and
for small children.
• Never allow children to operate the machine.
• Use extra care when approaching blind corners, shrubs, trees,
or other objects that may obscure vision.
Never
assume that children will remain
down
IV. SERVICE
• Use extra care in handling gasoline and other fuels. They are
flammable and vapors are explosive.
- Use only an approved container.
- Never remove gas cap or add fuel with the engine
running. Allow engine to cool before refueling. Do
not smoke.
- Never refuel the machine indoors.
- Never store the machine or fuel container inside
where there is an open flame, such as a water
heater.
• Never run a machine inside a closed area.
• Never make adjustments or repairs with the engine (motor)
running. Disconnect the spark plug wire, and keep the wire
away from the plug to prevent accidental starting.
• Keep nuts and bolts, especially blade attachement bolts, tight
and keep equipment in good condition.
• Never tamper with safety devices. Check their proper
operation regularly.
• Keep machine free of grass, leaves, or other debris build-up.
Clean oil or fuel spillage. Allow machine to cool before storing.
• Stop and inspect the equipment if you strike an object. Repair,
if necessary, before restarting.
• Never attempt to make wheel height adjustments while the
engine (motor) is running.
• Grass catcher components are subject to wear, damage, and
deterioration, which could expose moving parts or allow
objects to be thrown. Frequently check components and
replace with manufacturer’s recommended parts, when necessary.
• Mower blades are sharp and can cut. Wrap the blade(s) or
wear gloves, and use extra caution when servicing them.
• Do not change the engine governor setting or overspeed the
engine.
2
Page 3
Look for this symbol to point out important safety precautions. It means
CAUTION!!! BECOME ALERT!!! YOUR
SAFETY IS INVOLVED.
WARNING: Engine exhaust, some of its
constituents, and certain vehicle components contain or emit chemicals known
to the State of California to cause cancer
and birth defects or other reproductive
harm.
CAUTION: Always disconnect spark
plug wire and place wire where it cannot
contact spark plug in order to prevent
accidental starting when setting up,
transporting, adjusting or making repairs.
CAUTION: Muffler and other engine parts
become extremely hot during operation
and remain hot after engine has stopped.
To avoid severe burns on contact, stay
away from these areas.
CONGRATULATIONS on your purchase of a new lawn
mower. It has been designed, engineered and manufactured
to give you the best possible dependability and performance.
Should you experience any problem you cannot easily
remedy, please contact your nearest authorized service
center/department. We have competent, well-trained technicians and the proper tools to service or repair this lawn
mower.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your lawn mower
properly. Always observe the “SAFETY RULES”.
WARNING: Battery posts, terminals and
related accessories contain lead and
lead compounds, chemicals known to
the State of California to cause cancer
and birth defects or other reproductive
harm. Wash hands after handling.
PRODUCT SPECIFICATIONS
GASOLINE CAPACITY 1.6 QUARTS
AND TYPE: UNLEADED REGULAR ONLY
OIL TYPE (API-SF-SJ): SAE 30 (above 32°F)
SAE 5W-30 (BELOW 32°F)
OIL CAPACITY: 20 OUNCES
SPARK PLUG: Champion RJ19LM
(GAP: .030")
BLADE BOLT TORQUE: 35-40 FT. LBS.
SERIAL
NUMBER: ____________________________________
DATE OF PURCHASE: __________________________
THE MODEL AND SERIAL NUMBERS WILL BE FOUND
ON A DECAL ATTACHED TO THE REAR OF THE LAWN
MOWER HOUSING.
YOU SHOULD RECORD BOTH SERIAL NUMBER AND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
TABLE OF CONTENTS
SAFETY RULES ........................................................ 2-3
PRODUCT SPECIFICATIONS ....................................... 3
CUSTOMER RESPONSIBILITIES ................................ 3
WARRANTY .................................................................. 4
ASSEMBLY ................................................................... 5
OPERATION ............................................................... 6-9
CUSTOMER RESPONSIBILITIES
• Read and observe the safety rules.
• Follow a regular schedule in maintaining, caring for and
using your lawn mower.
• Follow the instructions under “Maintenance” and “Storage” sections of this owner’s manual.
MAINTENANCE .......................................................10-12
MAINTENANCE SCHEDULE ....................................... 10
SERVICE AND ADJUSTMENTS ................................. 13
STORAGE ................................................................... 14
TROUBLESHOOTING ................................................. 15
REPAIR PARTS ...................................................... 16-17
3
Page 4
SECTION 1: LIMITED WARRANTY
Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original
purchaser to be free from defects in material and workmanship from the date of purchase for the
“Warranty Period” of the product as set forth below:
Lifetime Warranty: All tiller tines, trimmer shafts, ignition coils and modules on hand held product.
2-Year Warranty: Riding lawn mowers, yard and garden tractors, walk behind mowers, tillers, chain
saws, trimmers, brushcutters, clearing saws, snow blowers, handheld blowers, backpack blowers,
hedge trimmers, and electrical products for noncommercial, nonprofessional, non-institutional or
non-income producing use, except as herein stated. Emission control system components
necessary to comply with CARB-95 and EPA regulations, except for those components which are
part of engine systems manufactured by third party engine manufacturers for which the purchaser
has received a separate warranty with product information supplied at time of purchase.
1-Year Warranty: Power cutters, stump grinder, hydraulic pole pruners and hydraulic pole saws
for non-commercial, non-professional, non-institutional or non-income producing use. All trimmers,
brushcutters, clearing saws, hovering trimmers, stick edgers, backpack blowers, hand held
blowers, hedge trimmers and model series 580 & 600 walk-behind mowers used for commercial,
institution-al, professional or income producing purposes or use.
90-Day Warranty: Chain saws, power cutters, stump grinders, trimmers, brushcutters, clearing
saws, hovering trimmers, stick edgers, hedge trimmers, backpack blowers, hand held blowers,
4
hydraulic pole saws, hydraulic pole pruners, snow throwers or any Husqvarna product used for
rental purposes or use except as otherwise provided herein.
30 Day Warranty: Husqvarna bow guide bars, replacement parts including bar and chains, product
accessories, tools, display features and safety apparel.
SECTION 2: HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY
Husqvarna will repair or replace defective components without charge for parts or labor if a
component fails because of a defect in material or workmanship during the warranty period.
SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY
The following items are not covered by this warranty:
(1) Normal customer maintenance items which become worn through normal regular use, including,
but not limited to, belts, blades, blade adapters, bulbs, filters, guide bars, lubricants, rewind springs,
saw chain, spark plugs, starter ropes and tines;
(2) Natural discoloration of material due to ultraviolet light;
(3) Engine and drive systems not manufactured by Husqvarna; these items are covered by the
respective manufacturer’s warranty as provided in writing with the product information supplied at
the time of purchase; all claims must be sent to the appropriate manufacturer;
(4) Lawn and garden attachments are covered by a third party that gives a warranty, all claims for
warranty should be sent to the manufacturer; and
(5) Emission Control System components necessary to comply with CARB-95 and EPA regulations
which are manufactured by third party engine manufacturer.
(6) Batteries have a one-year prorated limited warranty with 100% replacement during the first 6
months.
WARRANTY STATEMENT
SECTION 4: EXCEPTIONS AND LIMITATIONS
This warranty shall be inapplicable to defects resulting from the following:
(1) Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust,
corrosion, or any adverse reaction due to incorrect storage or use habits;
(2) Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction
sheet furnished by Husqvarna;
(3) Alterations or modifications that change the intended use of the product or affects the product’s
performance, operation, safety, or durability, or causes the product to fail to comply with any applicable
laws; or:
(4) Additional damage to parts or components due to continued use occurring after any of the above.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE
REMEDY OF THE PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSE-QUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON
THESE PROD-UCTS EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THESE
PRODUCTS IS LIMIT-ED IN DURATION TO THE WARRANTY PERIOD AS DEFINED IN THE
LIMITED WARRANTY STATE-MENT.
HUSQVARNA RESERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE
PRODUCT WITHOUT NOTICE, AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY MANUFACTURED PRODUCTS.
Some states do not allow the exclusion of incidental or consequential damages, or limitations on how
long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state.
SECTION 5: CUSTOMER RESPONSIBILITIES
The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written in the maintenance section of the Owner’s/Operator’s manual. Should an operational problem or
failure occur, the product should not be used, but delivered as is to an authorized Husqvarna dealer
for evaluation. Proof of purchase, as explained in section 6, rests solely with the customer.
SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION
It is the Owner’s and Dealer’s responsibility to make certain that the Warranty Registration Card is
properly filled out and mailed to Husqvarna Forest & Garden Company. This card should be mailed within
ten (10) days from the date of purchase in order to confirm the warranty and to facilitate post-sale service.
Proof of purchase must be presented to the authorized Husqvarna dealer in order to obtain warranty
service. This proof must include date purchased, model number, serial number, and complete name
and address of the selling dealer. To obtain the benefit of this warranty, the product believed to be defective
must be delivered to an authorized Husqvarna dealer in a timely manner, no later than thirty (30) days
from date of the operational problem or failure. The product must be delivered at the owner’s expense.
Pick-up and delivery charges are not covered by this warranty. An authorized Husqvarna dealer can
be normally located through the “Yellow Pages” of the local telephone directory or by calling 1-800HUSKY62 for a dealer in your area.
HUSQVARNA
7349 STATESVILLE ROAD
CHARLOTTE, NC 28269-3702
531 83 81-23 11/99
Page 5
ASSEMBLY
Read these instructions and this manual in its entirety before
you attempt to assemble or operate your new lawn mower.
IMPORTANT: THIS LAWN MOWER IS SHIPPED WITHOUT
OIL OR GASOLINE IN THE ENGINE.
Your new lawn mower has been assembled at the factory
with the exception of those parts left unassembled for
shipping purposes. All parts such as nuts, washers, bolts,
etc., necessary to complete the assembly have been placed
in the parts bag. To ensure safe and proper operation of your
lawn mower, all parts and hardware you assemble must be
tightened securely. Use the correct tools as necessary to
ensure proper tightness.
TO REMOVE LAWN MOWER FROM CARTON
1. Remove loose parts included with mower.
2. Cut down two end corners of carton and lay end panel
down flat.
3. Remove all packing materials except padding between
upper and lower handle and padding holding operator
presence control bar to upper handle.
4. Roll lawn mower out of carton and check carton thorougly
for additional loose parts.
HOW TO SET UP YOUR LAWN MOWER
TO UNFOLD HANDLE (See Fig. 1)
IMPORTANT: UNFOLD HANDLE CAREFULLY SO AS
NOT TO PINCH OR DAMAGE CONTROL CABLES.
1. Raise handles until lower handle section locks into place
in mowing position.
2. Remove protective padding, raise upper handle section
into place on lower handle and tighten both handle
knobs.
3. Remove handle padding holding operator presence
control bar to upper handle.
Your lawn mower handle can be adjusted for your mowing
comfort. Refer to “ADJUST HANDLE” in the Service and
Adjustments section of this manual.
OPERATOR PRESENCE
CONTROL BAR
UPPER HANDLE
LOWER HANDLE
LIFT
UP
LIFT UP
FIG. 1
MOWING
POSITION
5
Page 6
OPERATION
KNOW YOUR LAWN MOWER
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER. Compare the
illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments. Save this manual
for future reference.
These symbols may appear on your lawn mower or in literature supplied with the product. Learn and understand their meaning.
OPERATOR PRESENCE CONTROL BAR
THROTTLE
CONTROL
ENGINE ZONE CONTROL CABLE
STARTER HANDLE
GASOLINE FILLER CAP
AIR FILTER
DISCHARGE GUARD
IMPORTANT: THIS LAWN MOWER IS SHIPPED
WITHOUT OIL OR GASOLINE IN THE ENGINE.
HANDLE KNOB
ENGINE OIL CAP WITH DIPSTICK
PRIMER
MUFFLER
HOUSING
WHEEL ADJUSTER (ON EACH WHEEL)
MEETS CPSC SAFETY REQUIREMENTS
Our rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute and
the U.S. Consumer Product Safety Commission. The blade turns when the engine is running.
OPERATOR PRESENCE CONTROL BAR - must be held
down to the handle to start the engine. Release to stop the
engine.
STARTER HANDLE - used for starting the engine.
THROTTLE CONTROL – used for starting the engine and
allows you to select either FAST or SLOW engine speed.
PRIMER - pumps additional fuel from the carburetor to the
cylinder for use when starting a cold engine.
6
Page 7
OPERATION
The operation of any lawn mower can result in foreign objects thrown into the eyes, which can result in
severe eye damage. Always wear safety glasses or eye shields while operating your lawn mower or
performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or
standard safety glasses.
HOW TO USE YOUR LAWN MOWER
ENGINE SPEED (See Fig. 2)
The engine speed is controlled by a throttle located on the
side of the upper handle. FAST position is for starting,
normal cutting, trimming and better grass bagging. SLOW
position is for light cutting, trimming and fuel economy.
SLOW
FAST
LOWER WHEELS FOR HIGH CUT
LEVER
RAISE WHEELS FOR LOW CUT
FIG. 3
PLATE
TAB
TO CONVERT MOWER (See Fig. 4)
Your mower is shipped ready to be used as a mulcher. To
convert to bagging or discharging:
• Lift discharge guard and remove mulcher plate.
• Mower can now be used for side discharge or optional
grass catcher can be attached.
• To return to mulching operation, simply reinstall mulcher
plate as shown.
CAUTION: Do not run your lawn mower
without discharge guard, approved grass
catcher or mulcher plate in place.
FIG. 2
ENGINE ZONE CONTROL
CAUTION: Federal regulations require
an engine control to be installed on this
lawn mower in order to minimize the
risk of blade contact injury. Do not under any circumstances attempt to defeat
the function of the operator control. The
blade turns when the engine is running.
• Your lawn mower is equipped with an operator presence
control bar which requires the operator to be positioned
behind the lawn mower handle to start and operate the
lawn mower.
TO ADJUST CUTTING HEIGHT (See Fig. 3)
Raise wheels for low cut and lower wheels for high cut, adjust
cutting height to suit your requirements. Medium position is
best for most lawns.
• To change cutting height, squeeze adjuster lever toward
wheel. Move wheel up or down to suit your requirements.
Be sure all wheels are in the same setting.
NOTE: Adjuster is properly positioned when plate tab inserts
into hole in lever. Also, 9-position adjusters (if so equipped)
allow lever to be positioned between the plate tabs.
OPENING
MULCHER PLATE
7
HOOKSHOUSING
TABHINGE ROD
FIG. 4
Page 8
OPERATION
BEFORE STARTING ENGINE
ADD OIL (See Fig. 5)
Your lawnmower is shipped without oil in the engine. Engine
holds 20 ounces of oil. For type and grade of oil to use, see
“ENGINE” in the Maintenance section of this manual.
1. Be sure lawnmower is level and area around oil fill is
clean.
2. Remove engine oil cap and fill to the full line on the
dipstick. Pour oil slowly. Do not over fill.
NOTE: Allow oil to settle down into engine for accurate
reading. To read proper level, tighten engine oil cap, then
remove it to read the dipstick.
3. Reinstall engine oil cap and tighten.
• Check oil level before each use. Add oil if needed. Fill
to full line on dipstick.
• Change the oil after every 25 hours of operation or each
season. You may need to change the oil more often
under dusty, dirty conditions.
ADD GASOLINE (See Fig. 5)
NOTE: Before filling fuel tank, remove and discard the debris
plug that is inside the tank.
• Fill fuel tank. Use fresh, clean, regular unleaded
gasoline with a minimum of 87 octane. Do not mix oil
with gasoline. Purchase fuel in quantities that can be
used within 30 days to assure fuel freshness.
WARNING: Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or methanol) can
attract moisture which leads to separation and formation of
acids during storage. Acidic gas can damage the fuel
system of an engine while in storage. To avoid engine
problems, the fuel system should be emptied before storage
of 30 days or longer. Drain the gas tank, start the engine and
let it run until the fuel lines and carburetor are empty. Use
fresh fuel next season. See Storage Instructions for
additional information. Never use engine or carburetor
cleaner products in the fuel tank or permanent damage may
occur.
CAUTION: Fill to bottom of gas tank
filler neck. Do not overfill. Wipe off any
spilled oil or fuel. Do not store, spill or
use gasoline near an open flame.
ENGINE
OIL CAP
GASOLINE
FILLER CAP
(DISCARD
DEBRIS
PLUG
INSIDE)
PRIMER
FIG. 5
TO START ENGINE
NOTE: Due to protective coatings on the engine, a small
amount of smoke may be present during the initial use of the
product and should be considered normal.
1. To start a cold engine, push primer three (3) times before
trying to start. Use a firm push. This step is not usually
necessary when starting an engine which has already
run for a few minutes.
2. Move throttle control lever to FAST position.
3. Hold operator presence control bar down to the handle
and pull starter handle quickly. Do not allow starter rope
to snap back.
TO STOP ENGINE
• To stop engine, release operator presence control bar.
NOTE: In cooler weather it may be necessary to repeat
priming steps. In warmer weather over priming may cause
flooding and engine will not start. If you do flood engine, wait
a few minutes before attempting to start and do not repeat
priming steps.
8
Page 9
OPERATION
MOWING TIPS
• Under certain conditions, such as very tall grass, it may
be necessary to raise the height of cut to reduce pushing
effort and to keep from overloading the engine and
leaving clumps of grass clippings. It may also be
necessary to reduce ground speed and/or run the lawn
mower over the area a second time.
• For extremely heavy cutting, reduce the width of cut by
overlapping previously cut path and mow slowly.
• For better grass bagging and most cutting conditions,
the engine speed should be set in the fast position.
• For side discharge lawn mowers, cutting in a counterclockwise direction, starting at the outside of the area to
be cut, spreads grass clippings more evenly and puts
less load on the engine. To keep clippings off of
walkways, flower beds, etc., make the first cuts in a
clockwise direction.
• Pores in cloth grass catchers can become filled with dirt
and dust with use and catchers will collect less grass.
To prevent this, regularly hose catcher off with water and
let dry before using.
• Keep top of engine around starter clear and clean of
grass clippings and chaff. This will help engine air flow
and extend engine life.
MULCHING MOWING TIPS
IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER
HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE
“CLEANING” IN THE MAINTENANCE SECTION OF THIS
MANUAL.
• The special mulching blade will recut the grass clippings
many times and reduce them in size so that as they fall
onto the lawn they will disperse into the grass and not be
noticed. Also, the mulched grass will biodegrade
quickly to provide nutrients for the lawn. Always mulch
with your highest engine (blade) speed as this will
provide the best recutting action of the blades.
• Avoid cutting your lawn when it is wet. Wet grass tends
to form clumps and interferes with the mulching action.
The best time to mow your lawn is the early afternoon.
At this time the grass has dried and the newly cut area
will not be exposed to the direct sun.
• For best results, adjust the lawn mower cutting height so
that the lawn mower cuts off only the top one-third of the
grass blades (See Fig. 6). If the lawn is overgrown it will
be necessary to raise the height of cut to reduce pushing
effort and to keep from overloading the engine and
leaving clumps of mulched grass. For extremely heavy
mulching, reduce your width of cut by overlapping
previously cut path and mow slowly.
MAX 1/3
FIG. 6
• Certain types of grass and grass conditions may require
that an area be mulched a second time to completely
hide the clippings. When doing a second cut, mow
across or perpendicular to the first cut path.
• Change your cutting pattern from week to week. Mow
north to south one week then change to east to west the
next week. This will help prevent matting and graining
of the lawn.
9
Page 10
MAINTENANCE
MAINTENANCE SCHEDULE
FILL IN DATES
AS YOU COMPLETE
REGULAR SERVICE
Check for Loose Fasteners
Clean/Inspect Grass Catcher
(If Equipped)
Clean Lawn Mower
M
Clean Under Drive Cover
O
(Power-Propelled Mowers)
W
Check drive belt/pulleys
E
(Power-Propelled Mowers)
R
Check/Sharpen/Replace Blade
Lubrication Chart
Clean Battery/Recharge
(Electric Start Mowers)
Check Engine Oil Level
E
Change Engine Oil
N
Clean Air Filter
G
Inspect Muffler
I
Clean or Replace Spark Plug
N
Replace Air Filter Paper Cartridge
E
E
E
S
S
U
U
H
H
C
C
A
A
E
E
E
R
R
O
F
FTE
E
A
B
E
10 H
Y
R
E
E
V
V
E
O
3
1,2
2
2
2
R
R
U
O
25 H
Y
E
S
R
R
U
O
S
Y
R
E
V
FO
E
B
4
N
S
O
S
A
E
TO
S
E
R
SERVICE DATES
R
E
G
A
1 - Change more often when operating under a heavy load or in high ambient temperatures.
2 - Service more often when operating in dirty or dusty conditions.
3 - Replace blades more often when mowing in sandy soil.
4 - Charge 48 hours at end of season.
GENERAL RECOMMENDATIONS
The warranty on this lawn mower does not cover items that
have been subjected to operator abuse or negligence. To
receive full value from the warranty, operator must maintain
mower as instructed in this manual.
Some adjustments will need to be made periodically to
properly maintain your unit.
All adjustments in the Service and Adjustments section of
this manual should be checked at least once each season.
• Once a year, replace the spark plug, clean or replace air
filter element and check blade for wear. A new spark
plug and clean/new air filter element assure proper airfuel mixture and help your engine run better and last
longer.
• Follow the maintenance schedule in this manual.
BEFORE EACH USE
1. Check engine oil level.
2. Check for loose fasteners.
LUBRICATION
Keep unit well lubricated (See “LUBRICATION CHART”).
IMPORTANT: DO NOT OIL OR GREASE PLASTIC WHEEL
BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT
DUST AND DIRT THAT WILL SHORTEN THE LIFE OF THE
SELF-LUBRICATING BEARINGS. IF YOU FEEL THEY
MUST BE LUBRICATED, USE ONLY A DRY, POWDERED
GRAPHITE TYPE LUBRICANT SPARINGLY.
10
SPRAY LUBRICANT
À
SEE “ENGINE” IN MAINTENANCE SECTION
Á
LUBRICATION CHART
Á
HANDLE BRACKET MOUNTING PINS
À
WHEEL
À
ADJUSTER
(ON EACH
WHEEL)
ENGINE OIL
DIS-
À
CHARGE
GUARD
HINGE PIN
Page 11
MAINTENANCE
LAWN MOWER
Always observe safety rules when performing any maintenance.
TIRES
• Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
BLADE CARE
For best results, mower blade must be kept sharp. Replace
bent or damaged blades.
TO REMOVE BLADE (See Fig. 7)
1. Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with spark plug.
2. Turn lawn mower on its side. Make sure air filter and
carburetor are up.
3. Use a wood block between blade and mower housing to
prevent blade from turning when removing blade bolt.
NOTE: Protect your hands with gloves and/or wrap blade
with heavy cloth.
4. Remove blade bolt by turning counter-clockwise.
5. Remove blade and attaching hardware (bolt, lock washer
and hardened washer).
NOTE: Remove the blade adapter and check the key inside
hub of blade adapter. The key must be in good condition to
work properly. Replace adapter if damaged.
TO REPLACE BLADE (See Fig. 7)
1. Position the blade adapter on the engine crankshaft. Be
sure key in adapter and crankshaft keyway are aligned.
2. Position blade on the blade adapter aligning the two (2)
holes in the blade with the raised lugs on the adapter.
3. Be sure the trailing edge of blade (opposite sharp edge)
is up toward the engine.
4. Install the blade bolt with the lock washer and hardened
washer into blade adapter and crankshaft.
5. Use block of wood between blade and lawn mower
housing and tighten the blade bolt, turning clockwise.
• The recommended tightening torque is 35-40 ft. lbs.
IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.
TO SHARPEN BLADE
NOTE: We do not recommend sharpening blade - but if you
do, be sure the blade is balanced.
Care should be taken to keep the blade balanced. An
unbalanced blade will cause eventual damage to lawn mower
or engine.
• The blade can be sharpened with a file or on a grinding
wheel. Do not attempt to sharpen while on the mower.
• To check blade balance, drive a nail into a beam or wall.
Leave about one inch of the straight nail exposed. Place
center hole of blade over the head of the nail. If blade is
balanced, it should remain in a horizontal position. If
either end of the blade moves downward, sharpen the
heavy end until the blade is balanced.
BLADE ADAPTER
KEY
BLADE
LOCK
WASHER
BLADE
BOLT
HARDENED
WASHER
TRAILING EDGE
CRANKSHAFT
KEYWAY
CRANK-
SHAFT
BLADE ADAPTER
FIG. 7
11
Page 12
MAINTENANCE
GRASS CATCHER
(If purchased as an accesssory)
• The grass catcher may be hosed with water, but must be
dry when used.
• Check your grass catcher often for damage or deterioration. Through normal use it will wear. If catcher needs
replacing, replace only with a manufacturer approved
replacement catcher. Give the lawn mower model
number when ordering.
ENGINE
Read the Maintenance section of your engine manual.
LUBRICATION
Use only high quality detergent oil rated with API service
classification SF-SJ. Select the oil's SAE viscosity grade
according to your expected operating temperature.
SAE VISCOSITY GRADES
SAE 30
5W-30
-20 0 30 40
F
C
-30
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
-20 0
-10
32
10
60
80
20 30 40
100
CONTAINER
FIG. 8
AIR FILTER
Your engine will not run properly and may be damaged by
using a dirty air filter. Replace the air filter every 100 hours
of operation or every season, whichever occurs first. Service air cleaner more often under dusty conditions. See the
maintenance section of your engine manual.
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
32°F. Check your engine oil level more frequently to avoid
possible engine damage from running low on oil.
Change the oil after every 25 hours of operation or at least
once a year if the lawn mower is not used for 25 hours in one
year.
Check the crankcase oil level before starting the engine and
after each five (5) hours of continuous use. Tighten oil plug
securely each time you check the oil level.
TO CHANGE ENGINE OIL (See Fig. 8)
NOTE: Before tipping lawn mower to drain oil, drain fuel tank
by running engine until fuel tank is empty.
1. Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with spark plug.
2. Remove engine oil cap; lay aside on a clean surface.
3. Tip lawn mower on its side as shown and drain oil into a
suitable container. Rock lawn mower back and forth to
remove any oil trapped inside of engine.
4. Wipe off any spilled oil from lawn mower or side of
engine.
5. Fill engine with oil. (See “ADD OIL” in the Operation
section of this manual.)
6. Reconnect spark plug wire to spark plug.
MUFFLER
Inspect and replace corroded muffler as it could create a fire
hazard and/or damage.
SPARK PLUG
Replace spark plugs at the beginning of each mowing
season or after every 100 hours of operation, whichever
occurs first. Spark plug type and gap setting are shown in
“PRODUCT SPECIFICATIONS” in the Maintenance section
of this manual.
CLEANING
IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER
HOUSING FREE OF BUILT-UP GRASS AND TRASH.
CLEAN THE UNDERSIDE OF YOUR MOWER AFTER EACH
USE.
CAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with spark plug.
• Clean the underside of your lawn mower by scraping to
remove build-up of grass and trash.
• Clean engine often to keep trash from accumulating. A
clogged engine runs hotter and shortens engine life.
• Keep finished surfaces and wheels free of all gasoline,
oil, etc.
• We do not recommend using a garden hose to clean lawn
mower unless the electrical system, muffler, air filter
and carburetor are covered to keep water out. Water in
engine can result in shortened engine life.
12
Page 13
SERVICE AND ADJUSTMENTS
CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:
1. Release control bar and stop engine.
2. Make sure the blade and all moving parts have completely stopped.
3. Disconnect spark plug wire from spark plug and place where it cannot come in contact with plug.
LAWN MOWER
TO ADJUST CUTTING HEIGHT
See “TO ADJUST CUTTING HEIGHT” in the Operation
section of this manual.
REAR DEFLECTOR
The rear deflector, attached between the rear wheels of your
mower, is provided to minimize the possibility that objects
will be thrown out of the rear of the mower into the operator's
mowing position. If the deflector becomes damaged, it
should be replaced.
DISCHARGE GUARD
The discharge guard, attached to the discharge opening of
your lawn mower, is provided to prevent the possibility of
injury resulting from objects being thrown out of the discharge opening into the operator mowing position. If the
discharge guard becomes damaged, it should be replaced.
LOWER
HANDLE
TO ADJUST HANDLE (See Figs. 9 and 10)
The handle can be mounted in a high or low position. The
mounting holes in the bottom of lower handle are off center
for raising or lowering the handle.
1. Remove upper handle and all parts attached to lower
handle.
2. Remove hairpin cotters from lower handle bracket mounting pin.
3. Squeeze lower handle in to remove it from mounting
pins.
4. Turn lower handle over to raise or lower handle.
5. Squeeze lower handle in and position holes onto mounting pins on handle bracket.
6. Reassemble upper handle and all parts removed from
lower handle.
SQUEEZE
TO REMOVE
LOWER HANDLE
MOUNTING PIN
HANDLE
BRACKET
FIG. 9
HAIRPIN
COTTER
ROTATE
FIG. 10
ENGINE
ENGINE SPEED
Your engine speed has been factory set. Do not attempt to
increase engine speed or it may result in personal injury. If
you believe that the engine is running too fast or too slow,
take your lawn mower to an authorized service center for
repair and adjustment.
THROTTLE CONTROL
If it becomes necessary to adjust or replace the throttle
control, see the adjustment section of your engine manual.
CARBURETOR
Your carburetor is not adjustable. If your engine does not
operate properly due to suspected carburetor problems, take
your lawn mower to an authorized service center for repair
and/or adjustment.
IMPORTANT: NEVER TAMPER WITH THE ENGINE
GOVERNOR, WHICH IS FACTORY SET FOR PROPER
ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE
THE FACTORY HIGH SPEED SETTING CAN BE
DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED
HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR
NEAREST AUTHORIZED SERVICE CENTER, WHICH HAS
PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY
NECESSARY ADJUSTMENTS.
13
Page 14
STORAGE
Immediately prepare your lawn mower for storage at the end
of the season or if it will not be used for 30 days or more.
OPERATOR PRESENCE
CONTROL BAR
LAWN MOWER
When lawn mower is to be stored for a period of time, clean
it thoroughly, remove all dirt, grease, leaves, etc. Store in
a clean, dry area.
1. Clean entire lawn mower (See “CLEANING” in the
Maintenance section of this manual).
2. Lubricate as shown in the Maintenance section of this
manual.
3. Be sure that all nuts, bolts, screws, and pins are
securely fastened. Inspect moving parts for damage,
breakage and wear. Replace if necessary.
4. Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
HANDLE (See Figs.11 and 12)
You can fold your lawn mower handle for storage.
1. Squeeze the bottom ends of the lower handle toward
each other until the lower handle clears the handle
bracket, then move handle forward.
2. Loosen upper handle mounting bolts enough to allow
upper handle to be folded back.
IMPORTANT: WHEN FOLDING THE HANDLE FOR
STORAGE OR TRANSPORTATION, BE SURE TO FOLD
THE HANDLE AS SHOWN OR YOU MAY DAMAGE THE
CONTROL CABLES.
• When setting up your handle from the storage position,
the lower handle will automatically lock into the mowing
position.
SQUEEZE TO FOLD
LOWER HANDLE
UPPER HANDLE
LOWER
HANDLE
FOLD
FORWARD
FOR
STORAGE
FOLD
BACKWARD
MOWING
POSITION
FIG. 12
ENGINE
FUEL SYSTEM
IMPORTANT: IT IS IMPORTANT TO PREVENT GUM
DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM
PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL
HOSE, OR TANK DURING STORAGE. ALSO,
EXPERIENCE INDICATES THAT ALCOHOL BLENDED
FUELS (CALLED GASOHOL OR USING ETHANOL OR
METHANOL) CAN ATTRACT MOISTURE WHICH LEADS
TO SEPARATION AND FORMATION OF ACIDS DURING
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL
SYSTEM OF AN ENGINE WHILE IN STORAGE.
1. Drain the fuel tank.
2. Start the engine and let it run until the fuel lines and
carburetor are empty.
• Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage
container. Always follow the mix ratio found on stabilizer
container. Run engine at least 10 minutes after adding
stabilizer to allow the stabilizer to reach the carburetor. Do
not drain the gas tank and carburetor if using fuel stabilizer.
FIG. 11
ENGINE OIL
Drain oil (with engine warm) and replace with clean engine oil.
(See “ENGINE” in the Maintenance section of this manual).
CYLINDER
1. Remove spark plug.
2. Pour one ounce (29 ml) of oil through spark plug hole into
cylinder.
3. Pull starter handle slowly a few times to distribute oil.
4. Replace with new spark plug.
14
Page 15
OTHER
• Do not store gasoline from one season to another.
• Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
• If possible, store your unit indoors and cover it to give
protection from dust and dirt.
• Cover your unit with a suitable protective cover that does
not retain moisture. Do not use plastic. Plastic cannot
breathe, which allows condensation to form and will
cause your unit to rust.
IMPORTANT: NEVER COVER MOWER WHILE ENGINE
AND EXHAUST AREAS ARE STILL WARM.
CAUTION: Never store the lawn mower
with gasoline in the tank inside a building where fumes may reach an open
flame or spark. Allow the engine to cool
before storing in any enclosure.
TROUBLESHOOTING CHART
PROBLEM CAUSE CORRECTION
Does not start 1. Dirty air filter. 1. Clean/replace air filter.
2. Out of fuel. 2. Fill fuel tank.
3. Stale fuel. 3. Drain tank and refill with fresh, clean fuel.
4. Water in fuel. 4. Drain fuel tank and carburetor and refill tank
with fresh, clean fuel.
5. Spark plug wire is disconnected. 5. Connect wire to plug.
6. Bad spark plug. 6. Replace spark plug.
7. Loose blade or broken blade adapter. 7. Tighten blade bolt or replace blade adapter.
8. Control bar in released position. 8. Depress control bar to handle.
9. Control bar defective. 9. Replace control bar.
Loss of power 1. Rear of lawn mower housing or cutting 1. Set to “Higher Cut” position.
blade dragging in heavy grass.
2. Cutting too much grass. 2. Set to “Higher Cut” position.
3. Dirty air filter. 3. Clean/replace air filter.
4. Buildup of grass, leaves and trash under 4. Clean underside of mower housing.
mower.
5. Too much oil in engine. 5. Check oil level.
6. Walking speed too fast. 6. Cut at slower walking speed.
Poor cut – 1. Worn, bent or loose blade. 1. Replace blade. Tighten blade bolt.
uneven 2. Wheel heights uneven. 2. Set all wheels at same height.
3. Buildup of grass, leaves and trash under 3. Clean underside of mower housing.
mower.
Excessive 1. Worn, bent or loose blade. 1. Replace blade. Tighten blade bolt.
vibration 2. Bent engine crankshaft. 2. Contact a qualified service center.
Starter rope 1. Engine flywheel brake is on when control 1. Depress control bar to upper handle before
hard to pull bar is released. pulling starter rope.
2. Bent engine crankshaft. 2. Contact a qualified service center.
3. Blade adapter broken. 3. Replace blade adapter.
4. Blade dragging in grass. 4. Move lawn mower to cut grass or other hard
surface before starting.
Grass catcher 1. Cutting height too low. 1. Raise cutting height.
not filling 2. Lift on blade worn off. 2. Replace blade.
(if so equipped) 3. Catcher not venting air. 3. Clean grass catcher.
Hard to push 1. Grass is too high or wheel height is too low. 1. Raise cutting height.
2. Rear of lawn mower housing or cutting 2. Raise rear of lawn mower housing one (1)
blade dragging in heavy grass. setting higher.
3. Grass catcher too full. 3. Empty grass catcher.
4. Handle height position not right for you. 4. Adjust handle height to suit.
15
Page 16
REPAIR PARTS
16
ROTARY LAWN MOWER - - MODEL NUMBER 6022SH (6022SHB)
Page 17
REPAIR PARTS
ROTARY LAWN MOWER - - MODEL NUMBER 6022SH (6022SHB)
17
KEY PART
NO. NO. DESCRIPTION
1 532 06 36-01 Locknut 1/4-20
2 532 17 65-63 Control Bar
3 532 17 95-85 Rope Guide
4 532 17 36-93 Upper Handle (with Foam Grip)
5 532 17 42-91 Lower Handle
6 532 06 36-01 Locknut 1/4-20
7 532 13 19-59 Handle Bolt 5/16-18
8 532 14 49-29 Hex Washer Head Screw 1/4-20 x 2-1/8
9 532 16 41-37 Throttle Control
11 532 13 31-07 Engine Zone Control Cable
12 532 75 00-97 Hex Washer Head Screw #10-24 x 1/2
13 532 12 51-62 Up-Stop Bracket
14 532 21 31-46 Cable Clamp
15 532 08 38-16 Screw #10 x 5/8
16 532 13 63-76 Handle Knob
19 532 05 17-93 Hairpin Cotter
21 532 16 58-58 Rear Deflector
22 532 06 64-26 Wire Tie
23 532 17 65-61 Discharge Guard
27 532 16 08-32 Torsion Spring
30 532 16 08-33 Hinge Rod
33 532 06 31-24 Locknut 5/16-18
34 532 17 44-13 Wheel Bracket Support (Left)
35 532 17 44-14 Wheel Bracket Support (Right)
36 532 16 57-04 Wheel Bracket Adjuster
39 532 16 85-99 Selector Spring
40 532 08 78-77 Selector Knob
43 819 11 22-22 Washer
44 532 16 08-28 Shoulder Bolt
45 532 75 20-63 Wheel Assembly (Rear)
46 532 08 39-23 Locknut 1/16-18
KEY PART
NO. NO. DESCRIPTION
47 532 75 05-50 Wheel Assembly (Front)
48 532 05 71-43 Washer
50 532 07 74-00 Hubcap
51 874 76 05-14 Hex Head Bolt 5/16-18x
52 532 15 04-06 Hex Head Thread Rolling Screw 3/8-16 x 1
55 532 10 73-39 Danger Decal
59 532 17 65-65 Lawn Mower Housing (Includes Key #55)
61 532 85 15-14 Blade Adapter
62 532 14 11-14 22" Blade
63 532 85 10-74 Hardened Washer
64 532 85 02-63 Helical Lockwasher 3/8
65 532 85 10-84 Screw Hex Head 3/8-24 x 1-3/8 (Grade 8)
67 - - - Engine, Briggs & Stratton, Model No. 12H802
(Order parts from engine manufacturer)
70 532 16 86-01 Axle Arm Assembly (LR)
71 532 16 86-02 Axle Arm Assembly (RR)
72 532 16 86-05 Axle Arm Assembly (LF)
73 532 16 86-04 Axle Arm Assembly (RF)
74 532 75 11-53 Nut
75 532 17 65-62 Plate, Mulcher
76 532 17 65-60 Clip, Closeout
77 874 76 04-12 Screw
78 532 16 42-65 Foam Grip
79 532 06 15-37 Washer
80 532 13 20-04 Nut, Hex 1/4-20
- - 532 18 03-11 Owner's Manual (English/French)
- - 532 16 23-00 Warning Decal(Not Shown)
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
Page 18
NOTES
18
Loading...