Husqvarna 544 93 62-01 User Manual

Operator’s manual & spare parts list.
It is the owner’s responsibility to ensure that all operators of this

machine have read and understood the content of this manual be­fore using the product! Careless or improper use of this machine
can cause serious or even fatal injury! Allow only competent adults
to operate this machine!

K 750

SpeedMill

SpeedMill 1

TABLE OF CONTENTS

Section Page No.

Table of Contents.............................................. 2

Contact Information.......................................... 2

Symbols............................................................. 3

Introduction....................................................... 4

Safety Instructions...................................... 4 - 5

What-Is-What (Part Identication)................... 6

CONTACT INFORMATION

Husqvarna Construction Products, North America

Section Page No.

Uses................................................................... 7

Tools.................................................................. 7

Assembly...................................................... 7 - 8

Operation...................................................... 7 - 8

Maintenance.................................................... 10

Spare Parts............................................... 10 - 11

Corporate Ofce

17400 West 119th Street, Olathe, Kansas 66061 USA

Corporate Ofce: 913-928-1000
Corp. Ofce Fax: [phone]

www.husqvarnacp.com

For local service, please contact your local Husqvarna Construction Products representative.

Para efectuar un servicio local, póngase en contacto con su representante local de

Husqvarna Construction Products.

Pour toute réparation, contacter le représentant local de Husqvarna Construction Products.

Für Service vor Ort wenden Sie sich bitte an Ihren örtlichen Vertreter von

Husqvarna Construction Products.

Neem voor plaatselijke service contact op met uw plaatselijke vertegenwoordiger van de constructie-

producten van Husqvarna.

Per assistenza, rivolgersi al rappresentante di zona della Husqvarna Construction Products.

För service på platsen, kontakta din lokala representant för Husqvarna Construction Products.

Para obter serviço técnico local, contactar o representante da Husqvarna Construction Products

Husqvarna Construction Products, North America

17400 West 119th Street, Olathe, Kansas 66061 USA

Toll-Free Telephone: [phone], Telephone: [phone], Fax: [phone]

2 SpeedMill

SAFETY SYMBOLS & DECALS

KEY TO SYMBOLS

Key to symbols

WARNING! The machine can be a
dangerous tool if used incorrectly or
carelessly, which can cause serious or fatal
injury to the operator or others.

Please read the operator’s manual carefully
and make sure you understand the
instructions before using the machine.

Always wear:

• Protective helmet

• Hearing protection

• Protective goggles or a visor

WARNING! Dust forms when cutting, this
can cause injuries if inhaled. Use an
approved breathing mask. Avoid inhaling
petrol fumes and exhaust fumes. Always
provide for good ventilation.

WARNING! Sparks from the cutting blade
can cause fire in combustible materials
such as: petrol (gas), wood, dry grass etc.

Stop, in the fixed position.

Other symbols/decals on the machine refer to special
certification requirements for certain markets.

Operator must wear head protection such as

Operator must wear protective footwear such

as safety shoes or safety boots!

The operator must wear protective cloth­ing appropriate to the work he is doing.
Never wear loose clothing or jewelry. Keep
long hair tied back. Keep your hair, cloth­ing, and gloves away from the rotating tool!

The working area must be completely clear,

well lit and all safety hazards removed.

a hard hat!

Operator must wear eye protection!

Operator must wear hearing protection!

Operator must wear respiratory

(Reference OSHA 29CFR 1910.95,

1910.133-138)

protection!

Any persons not involved in the work, should

FOR INFORMATION ON DECALS FOR

THE SPEEDMILL, SEE THE SPARE

PARTS LIST SECTION OF THIS DOCU-

FOR INFORMATION ON DECALS FOR

THE K 750 POWER CUTTER, SEE THE

SPARE PARTS LIST FOR THE K 750.

leave the area.

MENT.

SpeedMill 3

SAFETY INSTRUCTIONS

Introduction

Thank you for purchasing your new machine from Husqvar­na Construction Products. We have provided important
safety messages in this manual and on the machine.
Please read these messages carefully. A safety message
alerts you to potential hazards that could hurt you or others.
Each safety message is preceded by a symbol or the safety
alert symbol ( ) and one of two words, WARNING, or

CAUTION.

These signal words mean:

WARNING: Indicates a hazardous situation which, if not
avoided COULD result in death or serious injury.

CAUTION: Indicates a hazardous situation, which, if not
avoided, COULD result in minor or moderate injury. It may
also be used to alert against unsafe practices.
Each message tells you what the hazard is, what can hap­pen, and what you can do to avoid or reduce injury.

NOTICE: Indicates a hazardous situation which, if not
avoided, COULD result in property damage. Your machine
or other property can be damaged if you don’t follow this
instruction.

If the label is worn, damaged, or is illegible, it should be
replaced.

Contents of Package

Verify the contents of the package:

• SpeedMill Power Cutter.

• SpeedMill Bowl Assembly: 100mm (4”), 150mm (6”), and
200mm (8”) Bowls with Hub and 2.00” Nut.

• Document Package. Operation Manual for Power Cut­ter, Spare Parts List for Power Cutter, Operation Manual /
Spare Parts List for Speed Mill Accessory (This Document).

If these items are not included in the package, contact our
customer service department at the telephone number
shown in this document.

Safety Instructions:

WARNING!

Before starting up machine make sure you
completely read these instructions and the
power cutter operation manual. Be familiar with
operation of the machine before operation!

Your SpeedMill comes with two Operator’s
Manual’s. This one for the SpeedMill attach­ment and one for the K750 power head. It is the
owner’s responsibility to ensure that all opera­tors of this SpeedMill have read and under­stood the content of both manuals before using
the product.

WARNING!

NEVER use a SpeedMill as a standard power cutter. A
SpeedMill is ONLY for USES listed in this document.

Cut only PVC plastic pipe with a machine equipped with
a SpeedMill Accessory! DO NOT cut other materials.

Use ONLY High Speed Reinforced Abrasive Blades with
this machine.

DO NOT use carbide tipped, wood cutting, or circular
saw blades with this machine.

DO NOT use diamond or rescue blades with this ma­chine! Cutting plastics with a diamond or rescue blade
can cause kickback. The heat produced melts the
material and it sticks to the blade.

DO NOT cut ductile iron pipe with a SpeedMill.

DO NOT touch Bowl when machine is running. Speed-

Mill Bowl Rotates with Blade.

Before performing any maintenance, ALWAYS locate
the machine on a level surface with the engine / motor
OFF and the start switch in the OFF position, and the
power source disconnected.

EVACUATE PIPE CONTENTS before cutting; else EX­PLOSION may occur. Static electricity from the cutting
operation may cause sewer or other gas within the pipe
to explode.

4 SpeedMill

The working area must be completely
clear, well lit and all safety hazards
removed.

Any persons not involved in the work,
should leave the area.