Husqvarna 536LIRX User Manual

Oper ator’s manual

Manuel d’utilisation

Manual de instrucciones

536LiRX

Please r ead the operator’s manual carefully and make sure you understand the instructions before using the machine.

Lire attentivement et bien assimiler le manuel d’utilisation avant d’utiliser la machine.

Lea detenidamente el manual de instrucciones y asegúrese de entender su contenido antes de utilizar la máquina

EEEEnnnngggglllliiiisssshhhh ((((2222----22229999))

FFFFrrrreeeennnncccchhhh ((((33330000----55558888))

SSSSppppaaaannnniiiisssshhhh ((((55559999----88888888))

))

Li-ion

KEY T O SYMBOLS

Symbols on the mac hine:

ranslation of the original Swedish operating instruction.

WARNING! Trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’s manual. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.

Always wear:

• Approved hearing protection

• Approved eye protection

Max. speed of output shaft, rpm

The operator of the machine must ensure, while working, that no persons or animals come closer than 15 meters (50 ft.).

Machines ﬁtted with saw blades or grass blades can be thrown violently to the side when the blade comes into contact with a ﬁxed object. The blade is capable of amputating an arm or leg. Always keep people and animals at least 15 meters from the machine.

Always wear approved protective gloves.

Wear sturdy, non-slip boots.

Symbols on the product or its packaging indicate that this product cannot be handled as domestic waste. This product must be deposited at an appropriate recycling facility. (Applies to Europe only)

Watch out for thrown objects and ricochets.

6000

15 m

50FT

Direct current.

Control Panel

• Rotation direction

• Activate and deactivate button

• SavE mode The machine is equipped with a battery saving function (SavE).

• Warning indicator

Symbols on the batter y and/or on the battery charger:

This product m ust be deposited at an appropriate recycling facility. (Applies to Europe only)

Fail-safe transformer

Use and store battery charger only indoors.

Double insulation

Other symbols/decals on the mac hine refer to special certiﬁcation requirements for certain markets.

Symbols in the operator’ s manual:

The engine is s witch off by pressing the stop button. Always remove the battery to prevent the machine being started by accident.

Always wear approved protective gloves.

Regular cleaning is required.

Only use non-metallic, ﬂexible cutting attachments, i.e. trimmer heads with trimmer line.

Arrows which show limits for handle positioning.

– English

Visual check.

Remove the battery. IMPORTANT! Always remove the battery to prevent the machine being started by accident.

Li-ion

3 Y

KEY T O SYMBOLS

ou will ﬁnd the following labels on your lawn trimmer,

battery and battery charger:

Husqvarna AB Huskvarna SWEDEN

Lea atentamente el manual de instrucciones y

siga todas las advertencias e instrucciones de

seguridad. No trabaje cerca de tendidos

eléctricos. Consulte la normativa local para

conocer las distancias de seguridad con respecto

a tendidos eléctricos. Lleve siempre protección

para la cabeza los ojos y los oídos, así como

guantes y calzado de protección.

Utilice únicamente una bateria de

tipo BLi de Husqvarna.

Lire attentivement le mode d’emploi et suivre tous les

avertissements et les consignes de sécurité. Ne pas opérer

près des lignes aériennes. Consulter la réglementation locale

pour les distances d’éloignement sécuritaires des lignes

électriques aériennes. Porter un casque de sécurité, des

protecteurs oculaires et auditifs, des chaussures et des gants

de protection. Utiliser uniquement une batterie Husqvarna de

type BLi.

DANGER ADVERTENC IA

DANGER

Read the operating manual carefully and

follow all warnings and safety instructions.

Do not operate near overhead electric power

lines. Consult local regulations for safe

distances from overhead electric lines.

Wear head, eye and hearing protection and

protective footwear and gloves. Use only

Husqvarna BLi battery.

battery charger

BFP

EXXXXXX

English

–

Contents

KEY TO SYMBOLS

Symbols on the machine: ...................................... 2

Symbols on the battery and/or on the battery

charger: .................................................................

Symbols in the operator’s manual: ........................ 2

CONTENTS

Contents ............................................................... 4

Note the following before starting: ........................ 4

INTR ODUCTION

Dear customer! ..................................................... 5

WHA T IS WHAT?

What is what? ....................................................... 6

GENERAL SAFETY PRECA UTIONS

Gener al power tool safety warnings ...................... 7

Personal protective equipment ............................. 8

Battery and battery charger .................................. 9

Machine ′ s safety equipment ................................. 10

Cutting equipment ................................................. 12

ASSEMBL Y

Fitting the handlebar ............................................. 14

Assembling the guard. .......................................... 14

Dismantling the Trimmer Head .............................. 14

Assembly of grass blade and grass cutter ............ 15

Adjusting the harness and trimmer ....................... 15

Standard harness ................................................. 15

Transport position, handlebar ............................... 16

ATTERY HANDLING

Batter y .................................................................. 17

Battery charger ..................................................... 17

Transport and storage ........................................... 18

Disposal of the battery, battery charger and

machine ................................................................

ARTING AND STOPPING

Chec k before starting ............................................ 19

Connect battery to the machine ............................ 19

Starting and stopping ............................................ 20

ORKING TECHNIQUES

Gener al working instructions ................................ 21

MAINTENANCE

Inspection and maintenance ................................. 25

Troubleshooting schedule ..................................... 26

Maintenance schedule .......................................... 27

TECHNICAL D ATA

echnical data ....................................................... 28

Note the f ollowing before starting:

Please read the oper ator’s manual carefully. Maintenance, replacement, or repair of the emission

control devices and system may be performed by any nonroad engine repair establishment or individual.

ARNING! Long-term exposure to noise can result in permanent hearing impairment. Always use hearing protection.

ARNING! Under no circumstances may the design of the machine be modiﬁed without the permission of the manufacturer. Always use genuine accessories. Non-authorized modiﬁcations and/or accessories can result in serious personal injury or the death of the operator or others.

Your warranty may not cover damage or liability caused by the use of nonauthorized accessories or replacement parts.

ARNING! A lawn trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual.

– English

′

INTR ODUCTION

Dear customer!

Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the waterpowered plant. During over 300 years of continuous operation, the Husqvarna factory has produced a lot of different products, from wood stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the ﬁrst motor driven lawn mowers appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working today.

Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our highest priority. We develop, manufacture and market high quality motor driven products for forestry and gardening as well as for building and construction industry.

Your purchase gives you access to professional help with repairs and service whenever this may be necessary. If the retailer who sells your machine is not one of our authorized dealers, ask for the address of your nearest servicing dealer.

It is our wish that you will be satisﬁed with your product and that it will be your companion for a long time. Think of this operator

s manual as a valuable document. By following its ′ content (using, service, maintenance etc) the life span and the second-hand value of the machine can be extended. If you ever lend or sell this machine, make sure that the borrower or buyer gets the operator

Thank you for using a Husqvarna product. Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and

appearance of products without prior notice.

s manual, so they will also know how to properly maintain and use it.

English – 5

WHA T IS WHA T?

What is what?

Trimmer head 2 Cutting attachment guard 3 Shaft 4 Harness Quick release 5 Harness, hip pad 6 Handle adjustment 7 Handlebar 8 Power trigger 9 Power trigger lockout 10 Keypad 11 SavE button 12 Rotation direction 13 Warning indicator (ERROR LED) 14 Activate and deactivate button 15 Cord 16 Battery charger

17 Power on and warning indicator (ERROR LED) 18 4 mm hex key 19 Socket spanner 20 Trimmer head 21 Battery release buttons 22 Battery 23 Battery status 24 Battery indicator button 25 Transport guard 26 Hole for locking pin 4 mm hex key 27 Drive disc 28 Blade 29 Support cup 30 Support ﬂange 31 Locking nut 32 Operator’s manual

– English

GENERAL SAFETY PRECA UTIONS

General po wer tool safety warnings

ARNING! Read all safety warnings and

all instructions. Failure to follow the

warnings and instructions may result in electric shock, ﬁre and/or serious injury.

IMPOR TANT! Save all warnings and instructions for

future reference.

Please read the oper ator’s manual carefully and make sure you understand the instructions before using the machine.

Chec k before starting

Always remove the battery to prevent the machine being started by accident. Always disconnect the battery before any maintenace on the machine.

• Before using the machine and after any impact, check for signs of wear or damage and repair as necessary.

• Inspect the working area. Remove all loose objects, such as stones, broken glass, nails, steel wire, string, etc. that could be thrown out or become wrapped around the cutter or cutter guard.

• Check the motor for dirt and cracks. Clean off grass and leaves from the engine using a brush. Gloves should be worn when necessary.

• Check that the trimmer head is completely attached to the trimmer.

• Check that the machine is in perfect working order. Check that all nuts and screws are tight.

• Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data.

• The machine operator must ensure that no people or animals come closer than 15 metres while working. When several operators are working in the same area the safety distance should be at least 15 metres.

• Do an overall inspection of the machine before use, see maintenance schedule.

• National or local regulations may regulate the use. Comply to given regulations.

ersonal safety

The cutting tool does not stop immediately after the machine is turned off.

• The machine is only design for trimming.

• Keep bystanders away.

• Stay alert, watch what you are doing and use

common sense when operaing a power tool. Do not use a power tool while you are tired or under the inﬂuence of drugs, alcohol or medication.

•

moment of inattention while operating power tools may result in serious personal injury.

• This appliance is not intended for use by person (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

• Never allow children or other persons not trained in the use of the machine and/or the battery to use or service it. Local laws may regulate the age of the user.

• Store the equipment in a lockable area so that it is out of reach of children and unauthorized persons.

• Keep hands and feet away from the cutting area at all times and especially when switching on the motor.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away from moving parts.

long hair can be caught in moving parts.

• Wear personal protective equipment. See instructions under the heading ”Personal protective equipment”.

• Always use face or dust mask if operation is dusty.

• Turn off the machine when it has to be moved. Always remove the battery when passing the machine to another person.

• Transport guard must always be used for storage and transport.

• Keep in mind that it is you, the operator that is responsible for not exposing people or their property to accidents or hazards.

Loose clothes, jewellery or

ower tool use and care

The only accessories you can operate with this product are the cutting attachment we recommend in the technical data chapter.

• Never use a machine that has been modiﬁed in any way from its original speciﬁcation. Never use the machine near explosive or ﬂammable materials.

• Never use a machine that is faulty. Carry out the safety checks, maintenance and service instructions described in this manual. Some maintenance and service measures must be carried out by trained and qualiﬁed specialists. See instructions under the heading Maintenance.

• Only use original spare parts.

• Always ensure that ventilation openings are kept clear of debris.

• Keep handles dry, clean and free from oil and grease.

• All covers, guards and handles must be ﬁtted before starting.

• Only use the machine in daylight or in other well-lit conditions.

• Do not overreach. Keep proper footing and balance at all times.

English

–

GENERAL SAFETY PRECA UTIONS

Don’t force the machine. It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.

• Never use the machine in bad weather, for instance in fog, in rain, damp or in wet locations, strong winds, intense cold, risk of lightning, etc. Extremely hot weather may cause overheating of the machine.

• If the machine starts vibrating abnormally, stop the machine and remove the battery.

• Walk, never run.

ways use common sense

It is not possib le to cover every conceivable situation you can face. Always exercise care and use your common sense. Avoid all situations which you consider to be beyond your capability. If you still feel uncertain about operating procedures after reading these instructions, you should consult an expert before continuing.

Impor tant

ARNING! This machine produces an

electromagnetic ﬁeld during operation.

This ﬁeld may under some circumstances interfere with active or passive medical implants. To reduce the risk of serious or fatal injury, we recommend persons with medical implants consult their physician and the medical implant manufacturer before operating this machine.

•

ersonal protective equipment

IMPOR TANT! A lawn trimmer can be dangerous if used incorrectly or

carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the content of this operator’s manual.

You must use approved personal protective equipment whenever you use the machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment.

WARNING! Listen out for warning signals or shouts when you are wearing hearing protection. Always remove your hearing protection as soon as the motor stops.

ARNING! There is a risk of burns as the gear housing can become very hot. Use gloves when working with the trimmer head.

HEARING PROTECTION Wear hearing protection that provides adequate noise

reduction.

– English

ARNING! Never allow children to use or be in the vicinity of the machine. Since the machine is easy to start, children may be able to start it if they are not kept under full surveillance. This can mean a risk of serious personal injury. Therefore disconnect the battery when the machine is not under close supervision.

EYE PROTECTION Always wear approved eye protection. If you use a visor

then you must also wear approved protective goggles. Approved protective goggles must comply with standard ANSI Z87.1 in the USA or EN 166 in EU countries.

GLOVES Gloves should be worn when necessary, e.g., when ﬁtting

cutting attachments.

GENERAL SAFETY PRECAUTIONS

Li-ion

BOOTS Wear sturdy, non-slip boots.

CLOTHING Wear clothes made of a strong fabric and avoid loose

clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure hair so it is above shoulder level.

FIRST AID KIT Always have a ﬁrst aid kit nearby.

SAVE THESE INSTRUCTIONS

Battery and battery charger

This section describes the battery and battery charger safety for your battery product.

Only use Husqvarna original batteries for Husqvarna products and only charge them in an original battery QC charger from Husqvarna. The batteries are software encrypted.

Use only a Husqvarna original BLi battery in your machine.

Battery safety

WARNING! Avoid all skin contact with battery acid. Battery acid may cause skin irritation, burns or corrosive injuries. If you get acid in your eyes, do not rub but ﬂush your eyes with plenty of water for at least 15 minutes. See a doctor. You must wash any exposed skin with copious amounts of water and soap in case of incidental contact.

WARNING! Never connect the battery terminal to keys, coins, screws or other metal as this may short-circuit the battery. Never insert objects into the battery's air vents.

Unused batteries must be kept away from metal objects such as nails, coins, jewellery. Do not try to disassemble or crush the battery

• Use the battery in surroundings where temperatures are between -10

• Do not expose the battery to microwaves or high pressure.

• Never clean the battery or the battery charger with water. See instructions under the heading Maintenance.

• Store the battery out of reach of children.

• Protect the battery from rain and wet conditions.

°C (14 °F) and 40 °C (104 °F).

Battery charger safety

Li-ion

The rechargeable Husqvarna batteries, BLi, are exclusively used as a power supply for the relevant Husqvarna cordless appliances. To avoid injury, the battery must not be used as a power source for other devices.

WARNING! Protect the battery from direct sunlight, heat or open ﬂame. There

is a risk the battery may explode if it is thrown into an open ﬁre. There is a risk of burns and/or chemical burns.

Only use Chargers, Husqvarna QC, for charging the Husqvarna replacement batteries, BLi.

English – 9

GENERAL SAFETY PRECAUTIONS

WARNING! Minimise the risk of electric shock or short circuit as follows:

Never insert any object into the charger’s cooling slots.

Do not try to dismantle the battery charger.

Never connect the charger terminals to metal objects as this can short circuit the battery charger.

Use approved and intact wall sockets.

WARNING! Do not use the battery charger close to corrosive or ﬂammable

materials. Do not cover the battery charger. Pull out the plug to the battery charger in the event of smoke or ﬁre. Remember the risk of ﬁre.

• Regularly check that the battery charger connection wire is intact and that there are no cracks in it.

• Never carry the battery charger using the cord and never pull out the plug by pulling the cord.

• Use a residual-current device (RCI) for increased security. A residual-current device is ﬁtted to protect operators in case an electrical fault should occur.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use.

cord suitable for outdoor use reduces the risk of electric shock.

• Use only three-wire outdoor extension cords that have three-prong grounding plugs and grounding receptacles that accept the appliance’s plug.

• Keep all cords and extension cords away from water, oil and sharp edges. Make sure the cord is not pinched in doors, fences or the like. Otherwise it can cause the object to become live. Inspect extensions cords periodically and replace if damaged.

Do not use:

• a faulty or damaged battery charger or never use a faulty, damaged or deformed battery.

Use of a

• the battery in the rain or in wet conditions.

• the battery in direct sunlight. Use the battery charger only when the surrounding

temperature is between 5 Use the charger in an environment which is well ventilated, dry and free from dust.

°C (41 °F) and 40 °C (104 °F).

Machine′s safety equipment

This section describes the machine′s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is positioned on your machine.

The life span or the runtime of the machine can be reduced and the risk of accidents can increase if machine maintenance is not carried out correctly and if service and/or repairs are not carried out professionally. If you need further information please contact your nearest service workshop.

IMPORTANT! All servicing and repair work on the machine requires

special training. This is especially true of the machine safety equipment. If your machine fails any of the checks described below you must contact your service agent. When you buy any of our products we guarantee the availability of professional repairs and service. If the retailer who sells your machine is not a servicing dealer, ask him for the address of your nearest service agent.

WARNING! Never use a machine with faulty safety equipment. The machine’s safety equipment must be checked and maintained as described in this section. If your machine fails any of these checks contact your service agent to get it repaired.

Control Panel

Make sure the machine is switched on or off when the activate/deactivate button (1) is pressed and held (>1 sec.). The green LED (2) is lit or turned off.

′s

Do not charge:

• non-rechargeable batteries in the battery charger or use them in the machine.

• the battery in the battery charger outdoors.

10 – English

Flashing warning indicator (3) and green LED (2) is lit could indicate that:

GENERAL SAFETY PRECAUTIONS

Li-ion

• it is not possible to apply full power and, at the same time, activate the machine. Release the power trigger and the machine is active.

• the machine is blocked. Deactivate the machine. Disconnect the battery. Remove the grass or other material that is wrapped around the trimmer head or gras blade.

• the machine is overloaded due to heavy trimming. Release the power trigger and the machine is active.

If the warning symbol (3) ﬂashes, it indicates that the machine is too hot and the machine deactivates. When the machine is restored to normal temperature it is again ready to run.

Solid light indicates service.

Power trigger lockout

The power trigger lockout is designed to prevent accidental operation of the power trigger. When you press the lock (1) (i.e. when you grasp the handle) it releases the power trigger (2). When you release the handle the power trigger and the power trigger lockout both move back to their original positions. This movement is controlled by two independent return springs.

Press the power trigger and make sure it returns to its original position when you release it.

Check that the power trigger and the power trigger lockout move freely and that the return spring works properly.

Make sure the power trigger is locked when the power trigger lock is in its original position.

See instructions under the heading Start. Start the machine and apply full power. Release the power trigger and check that the cutting attachment stops and remain at a standstill.

Cutting attachment guard

Li-ion

This guard is intended to prevent loose objects from being thrown towards the operator. The guard also protects the operator from accidental contact with the cutting attachment.

Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked.

Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data.

WARNING! Never use a cutting attachment without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is ﬁtted this can cause serious personal injury.

English – 11

GENERAL SAFETY PRECAUTIONS

Li-ion

WARNING! This machine is renowned for its low vibration load. Overexposure to

vibration can lead to circulatory damage or nerve damage in people who have impaired circulation. Contact your doctor if you experience symptoms of overexposure to vibration. These symptoms include numbness, loss of feeling, tingling, pricking, pain, loss of strength, changes in skin colour or condition. These symptoms normally appear in the ﬁngers, hands or wrists.

Locking nut

Li-ion

A locking nut is used to secure some types of cutting attachment.

When ﬁtting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. To remove it, undo the nut in the same direction as the cutting attachment rotates. (CAUTION! The nut has a left-hand thread.) Lock the blade shaft with the L key.

When loosening and tightening the saw blade nut, there is a risk of injury from the teeth of the saw blade. You should therefore always ensure that your hand is shielded by the blade guard when doing this. Always use a socket spanner with a shaft that is long enough to allow this. The arrow in the diagram shows the area where you should operate the socket spanner when loosening or tightening the nut.

Cutting equipment

Li-ion

This section describes how to choose and maintain your cutting equipment in order to:

• Reduce the risk of blade thrust.

• Obtain maximum cutting performance.

• Extend the life of cutting equipment.

IMPORTANT! Only use cutting attachments with the guards we

recommend! See the chapter on Technical data. Refer to the instructions for the cutting attachment to

check the correct way to load the line and the correct line diameter.

Keep the teeth of the blade correctly sharpened! Follow our recommendations. Also refer to the instructions on the blade packaging.

The blade should be completely stationary once the throttle has returned to its original position.

WARNING! Always remove the battery before you work on any part of the cutting equipment. It continues to rotate even after the power trigger has been released. Check that the cutting equipment has stopped completely and remove the battery before you start any work on it.

Using an incorrect cutting attachment or an incorrectly sharpened blade increases the risk of blade thrust.

Always wear protective gloves.

Grass blades and grass knifes are intended for cutting coarse grass.

The nylon lining inside the locking nut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.5 Nm. The nut should be replaced after it has been put on approx. 10 times.

12 – English

A trimmer head is intended for trimming grass.

GENERAL SAFETY PRECAUTIONS

General rules

Only use cutting attachments with the guards we recommend! See the chapter on Technical data.

Keep the cutting edge properly sharpened! Follow our instructions and use the recommended sharpner. A damaged or badly sharpened blade increases the risk of accidents, snags and thrust.

Keep the teeth of the blade correctly sharpened! Follow our instructions and use the recommended ﬁle gauge. An incorrectly sharpened or damaged blade increases the risk of accidents.

Check the cutting attachment for damage or cracks. A damaged cutting attachment should always be replaced.

WARNING! Using an incorrect cutting attachment or an incorrectly sharpened

blade increases the risk of blade thrust.

WARNING! Always discard a blade that is bent, twisted, cracked, broken or

damaged in any other way. Never attempt to straighten a twisted blade so that it can be reused. Only use original blades of the speciﬁed type.

Sharpening grass knifes and grass blades

• See the cutting attachment packaging for correct sharpening instructions.

• Sharpen all edges equally to maintain the balance of the blade.

Trimmer head

WARNING! Always use recommended trimmer line. See technical data. Failure to follow this instruction may cause personal injury.

IMPORTANT! Always ensure the trimmer line is wound tightly and

evenly around the drum, otherwise the machine will generate harmful vibration.

• Only use the recommended trimmer heads and trimmer lines. These have been tested by the manufacturer to suit a particular motor size. This is especially important when a fully automatic trimmer head is used. Only use the recommended cutting attachment. See the chapter on Technical data.

• Smaller machines generally require small trimmer heads and vice versa. This is because when clearing using a cord the engine must throw out the cord radially from the trimmer head and overcome the resistance of the grass being cleared.

• The length of the cord is also important. A longer cord requires greater engine power than a shorter cord of the same diameter.

• Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length.

• To increase the life of the cord it can be soaked in water for a couple of days before use. This will make the cord tougher so that it lasts longer.

• Different line lengths can result in unnecessary vibrations. Tap the trimmer head to get correct lengths on the line.

IMPORTANT! Save all warnings and instructions for future reference.

English – 13

ASSEMBLY

Li-ion

Fitting the handlebar

Li-ion

• Position the handlebar as shown. Fit the mounting components and tighten the knob lightly.

• Put on the harness and hang the machine from the support hook. Now make a ﬁnal adjustment so that the machine is in a comfortable working position when it hangs from the harness.

• Tighten the knob.

Dismantling the Trimmer Head

Li-ion

Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary.

Press the snap-in clips on the trimmer head and remove the trimmer head and line.

Pull out the line chute assembly.

Remove the nut holding the trimmer head and the drive disc.

Assembling the guard.

Li-ion

• Fit the correct trimmer guard (A) for use with the trimmer head.

• Hang the trimmer guard on the hook on the plate holder (1).

• Bend the guard around the shaft and tighten it with the bolt (2) on the opposite side of the shaft.

14 – English

ASSEMBLY

Li-ion

Assembly of grass blade and grass cutter

Li-ion

WARNING! When ﬁtting the cutting attachment it is extremely important that

the raised section on the drive disc/ support ﬂange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is ﬁtted incorrectly it can result in serious and/or fatal personal injury.

WARNING! Never use a cutting attachment without an approved guard.

See the chapter on Technical data. If an incorrect or faulty guard is ﬁtted this can cause serious personal injury.

Make sure the surface is level when ﬁtting the blade.

• Fit the drive disc (B) on the output shaft.

• Turn the output shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

• Insert the L key (C) into the hole to lock the shaft.

• Place the blade (D), support cup (E) and support ﬂange (F) on the output shaft.

• Fit the nut (G). Tighten the nut to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Grasp the handle of the spanner as close to the trimmer guard as possible.

Adjusting the harness and trimmer

WARNING! When using a trimmer it must always be hooked securely to the harness. Otherwise you will be unable to control the trimmer safetly and this can result in injury yourself or others. never use a harness with a defective quick release.

NOTE! Use the recommended blade guard.

Standard harness

Quick release

At the front is an easily accessible, quick release. Use this if the engine catches ﬁre or in any other emergency

situation that requires you to free yourself from the machine and harness.

English – 15

ASSEMBLY

Li-ion

Spreading the load on your shoulders

A well-adjusted harness and machine makes work much easier. Adjust the harness for the best working position. Tension the side straps so that the weight is evenly distributed across both shoulders.

Correct height

The machine should be supported in a harness when trimming so that the cutting equipment is parallel to the ground.

Transport position, handlebar

Li-ion

• The handlebar can easily be turned to ﬁt along the shaft for easier transportation and storage.

• Loosen the knob. Turn the handle clockwise so that the throttle handle touches the battery.

• Now twist the handlebar around the shaft. Tighten the knob.

Correct balance

Let the trimmer head balance at a comfortable cutting height, i.e. close to the ground.

16 – English

BATTERY HANDLING

Battery

The display shows the battery capacity and if there are any problems with the battery. The battery capacity is displayed for 5 seconds after the machine is switched off or the battery indicator button is pressed. The warning symbol on the battery is lit when an error has occurred. See fault codes.

LED lights Battery status

All LEDs are lit Fully charged (75-100%). LED 1, LED 2, LED 3 are

lit.

LED 1, LED 2 are lit.

LED 1 is lit.

LED 1 ﬂashes.

Battery charger

WARNING! Risk of electric shock and short circuiting. Use approved and intact

wall sockets. Make sure that the cable is not damaged. Replace cable if it appears to be damaged in any way.

Connect the battery charger

• Connect the battery charger to the voltage and frequency speciﬁed on the rating plate. Put the electric plug in a earthed socket-outlet. The LED on the battery charger ﬂashes green once.

The battery is 50%-75% charged.

The battery is 25%-50% charged.

The battery is 0%-25% charged.

The battery is empty. Charge the battery.

Connect the battery to the battery charger.

Regularly check that the battery charger and the battery are intact. See instructions under the heading Maintenance.

The battery must be charged before using it the ﬁrst time. The battery is only 30% charged when delivered.

• Put the battery in the battery charger. Make sure that the battery is connected to the battery charger.

• The green charging light on the charger is lit when the battery is connected to the battery charger.

• When all LEDs are lit the battery is fully charged.

• Pull out the plug. Never jerk the power supply cable to disconnect it from the wall socket.

• Remove the battery from the battery charger.

See separate manual for instructions on how to charge the backpack battery.

Charging status

Lithium-ion batteries can be charged at whatever charging level. The charging process can be cancelled or started whatever the battery’s charge level is. The battery is not damaged. A fully charged battery will not lose its charge even when the battery is left in the charger.

The battery will not be charged if the battery temperature is over 50

°C (122 °F).

• The battery will not be charged if the battery temperature is over 50 battery charger will actively cool down the battery.

°C (122 °F). In that case the

English – 17

BATTERY HANDLING

Li-ion

LED display Charging status

LED 1 ﬂashes.

LED 1 is lit, LED 2 ﬂashes.

LED 1, LED 2 are lit, LED 3 ﬂashes.

LED 1, LED 2, LED 3 are lit, LED 4 ﬂashes.

LED 1, LED 2, LED 3, LED 4 are lit.

Transport and storage

• The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.

• For commercial transports e.g. by third parties, forwarding agents, special requirement on packing and labeling must be observed.

• For preparation of the item being shipped, consulting an expert for hazardous material is required. Please also observe possibly more detailed national regulations.

• Tape or mask off open contacts and pack up the batteriy in such a manner that it cannot move around in the packing.

• Secure the machine during transport.

• Always remove the battery for storage or transport.

• Store the battery and the battery charger in a dry, moisture-free and frost-free space.

• To prevent accidents, ensure that your battery is not connected to the machine when stored.

• Do not store the battery in places where static electricity can occur. Never store the battery in a metal box.

• Store the battery where the temperature is between 5 °C (41 °F) and 25 °C (77 °F) and never in direct sunlight.

• Store the battery charger where the temperature is between 40

• Make sure the battery is charged to 30% - 50% before storing for long periods.

• Store the battery charger only in an enclosed and dry space.

• Be sure to store the battery separate from the battery charger. Store the equipment in a lockable area so that it is out of reach of children and unauthorized persons.

°F and 113 °F and never in direct sunlight.

The battery is 0%-25% charged.

The battery is 25%-50% charged.

The battery is 50%-75% charged.

Battery is 75%-100% charged

When all the LEDs are lit on the battery, it is fully charged.

Li-ion

• Ensure the machine is cleaned and that a complete service is carried out before long-term storage.

• Transport guard must always be used for storage and transport.

Disposal of the battery, battery charger and machine

Symbols on the product or its packaging indicate that this product cannot be handled as domestic waste. It must instead be submitted to an appropriate recycling station for the recovery of electrical and electronic equipment.

By ensuring that this product is taken care of correctly, you can help to counteract the potential negative impact on the environment and people that can otherwise result through the incorrect waste management of this product. For more detailed information about recycling this product, contact your municipality, your domestic waste service or the shop from where you purchased the product.

18 – English

STARTING AND STOPPING

Li-ion

Check before starting

Li-ion

• Check the motor for dirt and cracks. Clean off grass and leaves from the engine using a brush. Gloves should be worn when necessary.

• Check that the trimmer head is completely attached to the trimmer.

• Check that the machine is in perfect working order. Check that all nuts and screws are tight.

• Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth. Discard a blade if cracks are found.

• Check that the support ﬂange is not cracked due to fatigue or due to being tightened too much. Discard the support ﬂange if it is cracked.

trimmer guard if they have been exposed to impact or are cracked.

• Never use the machine without a guard nor with a defective guard.

• All covers must be correctly ﬁtted and undamaged before you start the machine.

• Only use the machine for the purpose it was intended for.

Connect battery to the machine

Make sure to use fully charged batteries. Use only a Husqvarna original battery in your machine. See technical data.

• Insert the battery in the machine. The battery should slide easily into the battery holder on the machine. If the battery does not slide in easily, it is not being inserted correctly. The battery will lock itself into place when you hear a click. Make sure the battery is ﬁtted correctly to the machine.

• Ensure the locking nut has not lost its captive force. The nut lock should have a locking force of at least 1.5 Nm. The tightening torque of the locking nut should be 35-50 Nm.

• Check that the blade guard is not damaged or cracked. Replace the blade guard if it is exposed to impact or is cracked.

• Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or

English – 19

STARTING AND STOPPING

Starting and stopping

WARNING! Make sure no unauthorised persons are in the working area,

otherwise there is a risk of serious personal injury. The safety distance is 15 meters (50 ft.).

Starting

Turn on the machine. Press and hold the start button (>1 sec.) until the green LED is lit.

Use the power trigger to control the speed.

IMPORTANT! The cutting attachment being used will be identiﬁed once the machine has been activated and the throttle depressed. When changing the cutting attachment from e.g. a trimmer head to a grass blade, the machine will stop and the LED lamp will ﬂash until the throttle is released to its original position. The cutting attachment has now been identiﬁed and the machine is ready to use.

Stopping

Stop the machine by releasing the throttle and the throttle lockout plus deactivating the machine.

Remove the battery from the machine by pressing the two release buttons and pulling out the battery.

IMPORTANT! Always remove the battery to prevent the machine being started by accident.

20 – English

WORKING TECHNIQUES

General working instructions

IMPORTANT! This section takes up the basic safety precautions for

working with a lawn trimmer. If you encounter a situation where you are uncertain

how to proceed you should ask an expert. Contact your dealer or your service workshop.

Avoid all usage which you consider to be beyond your capability.

WARNING! The machine can cause serious personal injury. Read the safety

instructions carefully. Learn how to use the machine.

WARNING! Always disconnect the battery before any maintenace on the

machine.

Basic safety rules

Wear personal protective equipment. See instructions under the heading ”Personal protective equipment”.

1 Look around you:

• To ensure that people, animals or other things cannot affect your control of the machine.

• To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out by the cutting attachment.

• CAUTION! Do not use the machine unless you are able to call for help in the event of an accident. Ensure that no-one comes closer than 15 m while you are working.

2 Inspect the working area. Remove all loose objects,

such as stones, broken glass, nails, steel wire, string, etc. that could be thrown out or become wrapped around the cutting attachment.

3 Never use the machine in bad weather, for instance in

fog, in rain, damp or in wet locations, strong winds, intense cold, risk of lightning, etc. Working in bad weather is tiring and can lead to dangerous conditions, e.g. slippery surfaces.

Safety instructions while working

• When working with a brush cutter the harness should always be worn. Otherwise you will be unable to control the brush cutter safely and this can result in injury to yourself or others. Never use a harness with a defective quick release.

• Make sure you can move and stand safely. Check the area around you for possible obstacles (roots, rocks, branches, ditches, etc.) in case you have to move suddenly. Take great care when working on sloping ground.

• Do not overreach. Keep proper footing and balance at all times.

• Always hold the machine with both hands. Hold the machine on the right side of your body.

• Don’t force the machine. It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.

• Keep all parts of your body away from the rotating cutting attachment. Keep the cutting attachment below waist level.

• Turn off the machine when it has to be moved. Always remove the battery when passing the machine to another person.

• Never put the machine down without turning it off ﬁrst and always remove the battery.

• If any foreign object is hit or if vibrations occur stop the machine immediately. Remove the battery from the machine and check that the machine is not damaged.

• If any unwanted vibrations occur, tap out new line to give the line the correct length and the vibrations should stop.

• Release the power trigger after each working operation to save battery power.

English – 21

WORKING TECHNIQUES

WARNING! Neither the operator of the machine nor anyone else may attempt to

remove the cut material while the motor is running or the cutting attachment is rotating, as this can result in serious injury.

Turn off the machine and remove the battery before removing materials that are wound around the trimmer head as otherwise there is risk of injury. The bevel gear can get hot during use and may remain so for a while afterwards. You could get burnt if you touch it.

WARNING! Watch out for thrown objects. Always wear approved eye protection.

Never lean over the cutting attachment guard. Stones, rubbish, etc. can be thrown up into the eyes causing blindness or serious injury.

Keep unauthorised persons at a distance. Children, animals, onlookers and helpers should be kept outside the safety zone of 15 m. (50 ft.) Stop the machine immediately if anyone approaches. Never swing the machine around without ﬁrst checking behind you to make sure no-one is within the safety zone.

Safety instructions after completing work

• Make sure the cutting attachment has stopped before cleaning, carrying out repairs or an inspection. Disconnect the battery.

SavE mode

The machine is equipped with a battery saving function (SavE). Activate the function by pressing the SavE button. A green LED will light to indicate that the function is on.

In most cases SavE mode is the most optimum when trimming and gives longest runtime. Release the power trigger after each working operation to save battery power.

Rotation direction

It is possible to change the rotation direction of the trimmer head in any position, at full speed or at stop postion.

Trimmer head

When the rotation button is pressed, the green diode will lit and the trimmer head rotates in counterclockwise. The trimmer head always rotates clockwise by default (green LED is off).

It is easier to tap out the trimmer line to make it longer when the trimmer head rotates clockwise.

Grass blade/grass cutter

When using the grass blade or grass knife, working rotation is anticlockwise only.

A clockwise direction of rotation is used to loosen any cut material that has fastened on the trimmer head or blade.

IMPORTANT! If the direction of rotation is changed to clockwise with blade, the blade speed will be reduced for a certain period and then again rotate anticlockwise.

Automatic switch off functionality

The machine is equipped with a shutdown feature that deactivates the machine if not used. The green LED will be extinguished and the machine turned off after 45 seconds.

Grass trimming with a trimmer head

22 – English

WARNING! Sometimes branches or grass get caught between the guard and cutting attachment. Always remove the battery before cleaning.

WORKING TECHNIQUES

Trimming

• Hold the trimmer head just above the ground at an angle. It is the end of the line that does the work. Let the line work at its own pace. Never press the line into the area to be cut.

• The line can easily remove grass and weeds up against walls, fences, trees and borders, however it can also damage sensitive bark on trees and bushes, and damage fence posts.

• Reduce the risk of damaging plants by shortening the line to 10-12 cm (0.32-0.39 ft.) and reducing the engine speed.

Clearing

• The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the line strike the ground around trees, posts, statues and the like. CAUTION! This technique increases the wear on the line.

• The line wears quicker and must be fed forward more often when working against stones, brick, concrete, metal fences, etc., than when coming into contact with trees and wooden fences.

• When trimming and clearing you should use less than full throttle (80%) so that the cord lasts longer and to reduce the wear on the trimmer head.

Cutting

• The trimmer is ideal for cutting grass that is difﬁcult to reach using a normal lawn mower. Keep the line parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.

• Do not allow the trimmer head to constantly come into contact with the ground during normal cutting. Constant contact of this type can cause damage and wear to the trimmer head.

Sweeping

• The fan effect of the rotating line can be used for quick and easy clearing up. Hold the line parallel to and above the area to be swept and move the tool to and fro.

• When cutting and sweeping you should use full throttle to obtain the best results.

Grass clearing using a grass blade

WARNING! Machines ﬁtted with grass blades can be thrown violently to the side when the blade comes into contact with a ﬁxed object. This is called blade thrust. A blade thrust can be violent enough to cause the machine and/or operator to be propelled in any direction, and possibly lose control of the machine. Blade thrust can occur without warning if the machine snags, stalls or binds. Blade thrust is more likely to occur in areas where it is difﬁcult to see the material being cut.

Avoid cutting with the area of the blade between the 12 o’clock and 3 o’clock positions. Because of the speed of rotation of the blade, blade thrust can occur if you attempt to cut thick stems with this area of the blade.

• Grass blades and grass knifes must not be used on woody stems.

• A grass blade is used for all types of tall or coarse grass.

• The grass is cut down with a sideways, swinging movement, where the movement from right-to-left is the clearing stroke and the movement from left-to-

English – 23

WORKING TECHNIQUES

right is the return stroke. Let the left-hand side of the blade (between 8 and 12 o’clock) do the cutting.

• If the blade is angled to the left when clearing grass, the grass will collect in a line, which makes it easier to collect, e.g. by raking.

• Try to work rhythmically. Stand ﬁrmly with your feet apart. Move forward after the return stroke and stand ﬁrmly again.

• Let the support cup rest lightly against the ground. It is used to protect the blade from hitting the ground.

• Reduce the risk of material wrapping around the blade by following these instructions:

- Always work at full throttle.

• Stop the engine, unclip the harness and place the machine on the ground before you start to collect the cut material.

24 – English

MAINTENANCE

Li-ion

Inspection and maintenance

Li-ion

WARNING! Always disconnect the battery before any maintenace on the

machine.

IMPORTANT! Never clean the battery or the battery charger with water. Strong cleaning agents can damage the plastic.

All servicing and repair work on the machine requires special training. This is especially true of the machine safety equipment. If your machine fails any of the checks described below you must contact your service agent. When you buy any of our products we guarantee the availability of professional repairs and service. If the retailer who sells your machine is not a servicing dealer, ask him for the address of your nearest service agent. Only use original spare parts.

Regularly check that the battery charger and the battery are intact.

′s

Trimmer line

Check the line by threading it into the hole on the cover, as shown in the illustration.

Only use the recommended trimmer heads and trimmer lines. These have been tested by the manufacturer to suit a particular motor size. This is especially important when a fully automatic trimmer head is used. Only use the recommended cutting attachment. See the chapter on Technical data.

Trimmer head

Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary.

• Press the snap-in clips on the trimmer head and remove the trimmer head and line.

Cleaning

Clean the machine after use. If the battery connector on the machine is dirty, clean it by blowing them with compressed air or use a soft brush.

Make sure the battery and battery charger are clean and that the terminals on the battery and the battery charger are always clean and dry before the battery is placed in the battery charger.

Keep the battery guide tracks clean. Clean plastic parts with a clean and dry cloth.

• Pull out the line chute assembly.

• Remove the nut holding the trimmer head and the drive disc.

• Replace the trimmer head.

• Fit the nut and the line chute assembly.

• Fit the trimmer head.

English – 25

MAINTENANCE

Troubleshooting schedule

Keypad

Troubleshooting takes place from the keypad.

Control Panel Possible faults Possible action

Green activate LED ﬂashing.

Error LED ﬂashes.

The machine does not start Dirt in battery connectors.

Error LED is lit with red light. Service Contact your service agent.

Battery

Troubleshooting the battery and/or the battery charger during charging.

LED display Possible faults Possible action

Green activate LED ﬂashing. Low battery voltage. Charge the battery.

Error LED ﬂashing

Error LED is lit Cell difference too much (1V). Contact your service agent.

Battery charger

Low battery voltage. Charging the battery Identifying the cutting tool Release the throttle The power trigger and the activate

button are pressed at the same time.

Overload.

Temperature deviation. Allow the machine to cool down.

The battery is discharged. Charge the battery.

Temperature deviation.

Release the power trigger and the machine is active.

The trimmerhead is jammed. Remove the battery from the

machine. Release the trimmer head from grass.

Clean with compressed air or a soft brush.

Use the battery in surroundings where temperatures are between -10 °C (14 °F) and 40 °C (104 °F).

LED display Possible faults Possible action

Use the battery charger only when the

Temperature deviation.

Error LED ﬂashing

Over voltage.

Error LED is lit Contact your service agent.

26 – English

surrounding temperature is between 5 °C (41 °F) and 40 °C (104 °F).

Check that the mains voltage corresponds with that stated on the rating plate on the machine.

Remove the battery from the battery charger.

MAINTENANCE

Li-ion

Maintenance schedule

Li-ion

WARNING! Always disconnect the battery before any maintenace on the

machine.

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section.

Maintenance

Clean the outside of the machine with a clean and dry cloth. Never use water.

Keep handles dry, clean and free from oil and grease. X Make sure that the activate and deactivate button works correctly

and is not damaged. Check that all controls are undamaged and in working order. X Make sure that the power trigger lock and the power trigger

function works correctly from a safety point of view. Check that the guard is undamaged and not cracked. Replace

the guard if it has been exposed to impact or is cracked. Check that the trimmer head is undamaged and not cracked.

Replace the trimmer head if necessary. Check that nuts and screws are tight. X Check that the battery is intact. X Check the battery's charge. X Check that the release buttons on the battery works and locks the

battery into the machine. Check that the battery charger is intact and functional. X Check that the harness is not damaged. X Check that all couplings, connections and cables are intact and

free from dirt. Check the connections between the battery and the machine and

also check the connection between battery and the battery charger.

Daily Maintenance

Weekly maintenance

Monthly maintenance

English – 27

TECHNICAL DATA

Technical data

536LiRX

Motor

Motor type BLDC (brushless) 36V Speed of output shaft, rpm 5500 Cutting width, inch/mm 16/400

Weight

Weight without battery, Lbs/kg 8.4/3.8 Weight with battery, Lbs/kg 11/5

Battery runtime

Battery runtime, min, (free run) with SavE activated 60

Sound levels

(see note 1) Equivalent sound pressure level at the operator’s ear,

measured according to EN ISO 60335-91-2 and ISO 22868, dB(A):

Equipped with trimmer head (original), left/right Equipped with grass blade (original), left/right

Vibration levels

(see note 2) Equivalent vibration levels (a

measured according to ISO 22867, m/s Equipped with trimmer head (original), left/right 1,2/0,7 Equipped with grass blade (original), left/right 2,8/1,6

Approved batteries for 536LiRX. BLi80 BLi110 BLi150

Type Lithium-ion Lithium-ion Lithium-ion Battery capacity, Ah 2,1 3.0 4,2 Voltage, V 36 36 36 Weight, lb/kg 1,7/0,8 1,2/2,6 1,3/2,8

) at handles,

hv,eq

Approved chargers for the speciﬁed batteries, BLi.

Battery charger QC330 Input Voltage, V 100-240 Frequency, Hz 50-60 Power, W 330

Note 1 Reported data for equivalent sound pressure level for the machine has a typical statistical dispersion (standard deviation) of 3 dB (A).

Note 2: Reported data for equivalent vibration level has a typical statistical dispersion (standard deviation) of 2 m/s2. The accessories are recommended for use in combination with the speciﬁed power heads and have been evaluated to

applicable ISO- and EN safety requirement standards by the Swedish Machinery Testing Institute. The accessories used in combination with the speciﬁed power heads have been evaluated to ANSI B175.3-2003 Grass

Trimmers and Brushcutters - Safety Requirements. These combinations have been evaluated by Underwriters Laboratories Inc. (UL) and are consequently UL listed.

28 – English

TECHNICAL DATA

Accessories Type Cutting attachment guard, Art. no.

Arbor shaft thread M10 Trimmer head T25B (Ø 2.0 mm line) 577 01 83-03 Grass blade/grass cutter Grass blade 255-4 (Ø 255 4-teeth) 577 01 83-03 Grass blade/grass cutter Grass blade 255-3 (Ø 255 3 teeth) 577 01 83-03 Support cup Fixed

English – 29

EXPLICATION DES SYMBOLES

Li-ion

Symboles sur la machine:

Traduction du manuel d’utilisation original du suédois. AVERTISSEMENT! Les coupe-herbes

peuvent être dangereux erronée ou négligente peut occasionner des blessures graves, voire mortelles pour l’utilisateur ou d’autres personnes. Il est extrêmement important de lire et de comprendre le contenu de ce manuel de l’opérateur. Lire attentivement et bien assimiler le manuel d’utilisation avant d’utiliser la machine.

Toujours utiliser:

• Protecteurs d’oreilles homologués

• Des protège-yeux homologués

Régime maxi. recommandé de l’axe sortant, tr/min

L’utilisateur de la machine doit s’assurer qu’aucune personne ou animal ne s’approche à moins de 15 mètres (50 ft.) pendant le travail.

Les machines équipées d’une lame d’éclaircissage ou à herbe peuvent être projetées violemment sur le côté quand la lame rencontre un objet dur. La lame peut sectionner les bras et les jambes. Toujours maintenir les personnes et les animaux à au moins 15 mètres de la machine.

Toujours porter des gants de protection homologués.

Utiliser des bottes antidérapantes et stables.

Ce symbole ﬁgurant sur le produit ou sur son emballage indique que ce produit ne peut pas être traité comme déchet ménager. Ce produit doit être remis à un centre de recyclage approprié.

Attention: projections et ricochets.

! Une utilisation

6000

15 m

50FT

Courant continu.

Panneau de commande

• Sens de rotation

• Bouton d'activation/ désactivation

• SavE mode La machine est équipée d'une fonction d'économie de la batterie (SavE).

• Avertisseur

Symboles sur la batterie et/ou son chargeur :

Ce produit doit être remis à un centre de recyclage approprié.

Transformateur non dangereux en cas de

défaillance

Utilisez et stockez le chargeur de batterie uniquement en intérieur.

Double isolation

Les autres symboles/autocollants présents sur la machine concernent des exigences de certiﬁcation spéciﬁques à certains marchés.

Symboles dans le manuel:

La machine s'allume et s'arrête à l'aide du bouton marche/arrêt. Retirez toujours la batterie aﬁn d'éviter tout démarrage accidentel de la machine.

Toujours porter des gants de protection homologués.

Un nettoyage régulier est indispensable.

Destiné uniquement à des équipements de coupe ﬂexibles et non métalliques, c’est-à-dire les têtes de désherbage avec ﬁl.

Flèches indiquant les limites quant à l’emplacement de la ﬁxation de la

30 – French

poignée.

Examen visuel.

Enlever la batterie. IMPORTANT! Retirez toujours la batterie aﬁn d'éviter tout démarrage accidentel de la machine.

Li-ion

+ 73 hidden pages