Husqvarna 130BT, 380BFS, 350BF, 115 31 90-95, 370BFS User Manual
WARNING
English
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects or other reproductive
WARNING
Before using our products, please read this manual
carefully to understand the proper use of your unit.
APPLICABLE SERIAL NUMBERS: 00100101 and up
Operator’s manual
130BT
350BT/BF
370BTS/BFS
380BTS/BFS
115 31 90-95Origianl Instructions
English
FEDERAL EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS
AND OBLIGATIONS
The EPA (The US Environmental Protection Agency),
CARB (California Air Resources Board), Environment
Canada and Husqvarna Forest & Garden are pleased to
explain the emissions control system warranty on your
2007 and later small nonroad engine. In U.S. and
Canada, new small nonroad engines must be designed,
built and equipped to meet the federal stringent antismog standards. Husqvarna Forest & Garden must
warrant the emission control system on your small
nonroad engine for the period of time listed below
provided there has been no abuse, neglect or improper
maintenance of your unit. Your emission control system
includes Parts such as the carburetor, fuel tank and the
ignition system. Where a warrantable condition exists,
Husqvarna Forest & Garden will repair your small
nonroad engine at no cost to you. Expenses covered
under warranty include diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COVERAGE
The 2007 and later small nonroad engines are
warranted for two years. If any emission related part on
you engine (as listed above) is defective, the part will be
repaired or replaced by Husqvarna Forest & Garden.
OWNER’S WARRANTY
RESPONSIBILITIES
As the small nonroad engine owner, you are responsible
for the performance of the required maintenance listed in
your Operator’s Manual. Husqvarna Forest & Garden
recommends that you retain all receipts covering
maintenance on your small nonroad engine, but
Husqvarna Forest & Garden cannot deny warranty
solely for the lack of receipts or for your failure to ensure
the performance of all scheduled maintenance. As the
small nonroad engine owner, you should, however, be
aware that Husqvarna Forest & Garden may deny you
warranty coverage if your small nonroad engine or a part
of it has failed due to abuse, neglect, improper
maintenance, unapproved modifications or the use of
parts not made or approved by the original equipment
manufacturer. You are responsible for presenting your
small nonroad engine to a Husqvarna Forest & Garden
authorized servicing dealer as soon as a problem exists.
The warranty repairs should be completed in a
reasonable amount of time, not to exceed 30 days. If you
have any questions regarding your warranty rights and
responsibilities, you should contact your nearest
authorized servicing dealer or call Husqvarna Forest &
Garden at 1-800-487-5963.
WARRANTY COMMENCEMENT DATE
The warranty period begins on the date small nonroad
engine is delivered.
LENGTH OF COVERAGE
Husqvarna Forest & Garden warrants to the initial owner
and each subsequent purchaser that the engine is free
from defects in materials and workmanship which cause
the failure of a warranted part for a period of two years.
WHAT IS COVERED
REPAIR OR REPLACEMENT OF PARTS
replacement of any warranted part will be performed at
no charge to the owner at an approved Husqvarna
Forest & Garden servicing dealer. If you have any
questions regarding your warranty rights and
Repair or
responsibilities, you should contact your nearest
authorized servicing dealer or call Husqvarna Forest &
Garden at 1-800-487-5963.
WARRANTY PERIOD
scheduled for replacement as required maintenance, or
which is scheduled only for regular inspection to the
effect of “repair or replace as necessary” shall be
warranted for 2 years. Any warranted part which is
scheduled for replacement as required maintenance
shall be warranted for the period of time up to the first
scheduled replacement point for that part.
DIAGNOSIS
diagnostic labor which leads to the determination that a
warranted part is defective, if the diagnostic work is
performed at an approved Husqvarna Forest & Garden
servicing dealer.
CONSEQUENTIAL DAMAGES
Garden may be liable for damages to other engine
components caused by the failure of a warranted part
still under warranty.
Any warranted part which is not
The owner shall not be charged for
Husqvarna Forest &
WHAT IS NOT COVERED
All failures caused by abuse, neglect or improper
maintenance are not covered.
ADD -ON OR MODIFIED PARTS
The use of add-on or modified parts can be grounds for
disallowing a warranty claim. Husqvarna Forest &
Garden is not liable to cover failures of warranted parts
caused by the use of add-on or modified parts.
HOW TO FILE A CLAIM
If you have any questions regarding your warranty rights
and responsibilities, you should contact your nearest
authorized servicing dealer or call Husqvarna Forest &
Garden at 1-800-487-5963.
WHERE TO GET WARRANTY
SERVICE
Warranty services or repairs shall be provided at all
Husqvarna Forest & Garden authorized servicing
dealers.
MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS
Any Husqvarna Forest & Garden approved replacement
part used in the performance of any warranty maintenance
or repairs on emission-related parts, will be provided
without charge to the owner if the part is under warranty.
EMISSION CONTROL WARRANTY PARTS LIST
1 Carburetor and internal parts
2 Intake pipe, airfilter holder and carburetor bolts.
3 Airfilter and fuelfilter covered up to maintenance
schedule.
4 Ignition System
1Spark Plug, covered up to maintenance schedule
2Ignition Module
5 Fuel tank with cap and pipe
MAINTENANCE STATEMENT
The owner is responsible for the performance of all
required maintenance, as defined in the operator’s
manual.
2
Contents
English
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
SAFETY FIRST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Notes on types of warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Warning labels on the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Symbols on the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
WORKING CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
WORKING CIRCUMSTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
AVOID NOISE PROBLEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
WORKING PLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
FUEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
BEFORE STARTING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . 7
USING THE PRODUCT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TRANSPORTATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
What is what?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
FLEXIBLE HOSE AND SWIVEL JOINT. . . . . . . . . . . . . . . . . . . . 14
CONTROL HANDLE [130BT/350BT/370BTS/380BTS]. . . . . . . . 14
CABLING [130BT/350BT/370BTS/380BTS] . . . . . . . . . . . . . . . . 14
RIGHT HANDLE [350BF/370BFS/380BFS]. . . . . . . . . . . . . . . . . 14
HANDLEBAR [OPTION] [130BT/350BT/370BTS/380BTS] . . . . . 14
BLOW PIPES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
HARNESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
WAIST BELT [350BT/BF] [370BTS/BFS] [380BTS/BFS] . . . . . . . 15
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
FUEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
HOW TO MIX FUEL . . . . . . . . . . . . . . . . . . . . . . 16
FUELING THE UNIT. . . . . . . . . . . . . . . . . . . . . . 16
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CONTROL ARM [350BF/370BFS/380BFS] . . . . 17
STARTING ENGINE . . . . . . . . . . . . . . . . . . . . . . 17
ADJUSTING IDLE SPEED . . . . . . . . . . . . . . . . . 18
STOPPING ENGINE. . . . . . . . . . . . . . . . . . . . . . 18
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
AIR CLEANER . . . . . . . . . . . . . . . . . . . . . . . . . . 19
FUEL FILTER . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SPARK PLUG . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
MUFFLER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SPARK ARRESTER . . . . . . . . . . . . . . . . . . . . . . 20
COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . 21
AIR INLET NET . . . . . . . . . . . . . . . . . . . . . . . . . 21
SHOLDER STRAP . . . . . . . . . . . . . . . . . . . . . . . 21
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3
English
Safety
SAFETY FIRST
Instructions contained in warnings within this manual
and warning seals marked with a symbol on the
blower concern critical points which must be taken into
consideration to prevent possible serious bodily injury,
and for this reason you are requested to read all such
instructions carefully and follow them without fail.
Warning labels on the machine
Symbols
WARNING! The machine can be
a dangerous tool if used
incorrectly or carelessly, which
can cause serious or fatal injury
to the operator or others.
Please read the operator’s manual
carefully and make sure you
understand the instructions before
using the machine.
Notes on types of warnings
WARNING
Instructions labeled as shown above, concern
critical steps or procedures which must be followed in order to prevent accidents which could
lead to serious bodily injury or death.This mark is
used to indicate instructions which must be followed without exception.
IMPORTANT
Instructions labeled as shown above concern
steps or procedures which, if not followed
correctly, could lead to mechanical failure,
breakdown, or damage.
NOTE
Used to label supplementary instructions
designed to provide hints or directions useful in
the use of the product.
The blower operator must
make sure that no
bystanders or animals come
nearer than 50 feet (15
meters). Whenever several
operators are working in the same work area, they
should maintain a safe distance of at least 50 feet (15
meters) from one another.
A breathing mask should be used
when there is a risk of dust.
Always wear:
-
Hearing protection
-
Approved eye protection
Always wear protective gloves.
Wear study, non-slip boots
The blower can forcibly throw objects
that can bounce back. This can result
in serious eye injuries if the
recommended safety equipment is
not used.
4
Keep all parts of your body away
from hot surfaces.
Other symbols/decals on the machine refer to
special certification requirements for certain
markets.
IMPORTANT
If the warning label peels off or becomes soiled
and impossible to read, you should contact the
dealer from which you purchased the product to
order new labels and affix them in the required
location(s).
Symbols on the machine
English
(c)
For safe operation and maintenance, symbols are carved in relief on the machine. Using to these indications, please be
careful not to make a mistake.
(a) The port to refuel the "MIX GASOLINE"
Position:
FUEL TANK CAP
(b) The direction to close the choke
Position:
INTAKE CUP
(e) The emission information label
(c) The direction to open the choke
Position:
INTAKE CUP
(d) The direction to stop the engine
Position:
CONTROL HANDLE[130 BT/350 BT/370
BTS/380BTS only]
(d)(a) (b)
∗
1 : THE ACTUAL MANUFACTURING MONTH WILL
BE PRINTED.
A : Model B : ENGINE
130BT
350BT/BF
370BTS/BFS
380BTS/BFS
∗
2 : THE INITIAL CODE WILL BE CHANGED EVERY
YEAR OF MANUFACTURING.
AHQZS.0294BK
AHQZS.0505BP
AHQZS.0655BE
AHQZS.0725PQ
FAMILY
∗
2
∗
2
∗
2
∗
2
ENGINE
C :
DISPLACEMENT
29cc
50cc
65cc
72cc
This engine label certifies that the product is certified in
accordance with American exhaust emissions
requirements EPA Ph III and CARB Tier III. The
Emissions Compliance Period referred to on the
emissions Compliance label indicates the number of
operating hours for which the engine has been shown to
meet Federal and California emission requirements.
For customer assistance call: 704-921-7000 or contact
us at our website: www.husqvarna.com
Safety Precautions
WARNING
1. Read this Blower Operator Manual carefully.
Be sure you understand how to operate this
unit properly before you use it. Failure to do so
could result in serious injury.
2. Be sure to keep this manual
handy so that you may refer to
it later whenever any questions
arise. Also note that you are
requested to contact the dealer
from whom you purchased the
product for assistance the
event that you have any questions which
cannot be answered herein.
3. Always be sure to include this manual when
selling, lending, or otherwise transferring the
ownership of this product.
4. Do not lend or rent your machine without the
owner's manul.
5. Be sure that anyone using your unit understands
the information contained in this manual.
6. Never let a child use the machine.
7.
Long-term exposure to noise can result in
permanent hearing impairment. So always
use approved hearing protection.
8.
Under no circumstances may the design of
the machine be modified without the
permission of the manufacturer. Always use
genuine accessories. Non-authorized
modifications and/or accessories can result
in serious personal injury or the death of the
operator or others.
9.
A blower is a dangerous tool if used
carelessly or incorrectly and can cause
serious, even fatal injuries. It is extremely
important that you read and understand the
contents of this Operator’s manual.
10.
Husqvarna AB has a policy of continuous
product development and therefore reserves
the right to modify the design and appearance
of products without prior notice.
11.
The machine is only designed for blowing
lawns, pathways, asphalt roads and the like.
WORKING CONDITIONS
5
English
Safety Precautions
1. Refrain from operating the blower if you are tired, ill,
or upset, or if you are under the influence of alcohol,
drugs or medication
2. To reduce the risk of hearing loss associated with
sound levels, hearing protection is
required.
3. To reduce the risk of injury
associated with thrown objects,
always wear eye protection and
foot protection. Approved protective
goggles must comply with standard
ANSI Z87.1 in the USA or EN 166
in EU countries.
4. To reduce the risk of injury
associated with the inhalation of
dust, use a face filter mask in dusty
conditions.
5. Wear rubber-soled shoes or shoes
with some other form of anti-slip
protection to help protect you
against falling.
6. To reduce the risk of injury
associated with objects being
drawn into rotating parts, do not
wear loose clothing, scarves, neck
chains, hair longer than shoulder
length, or other loose material.
7. Prolonged use of a blower, exposing the operator to
vibrations and cold, may produce whitefinger
disease (Raynaud’s phenomenon), the symptoms of
which include tingling and burning sensations
followed by loss of color and numbness in the
fingers. All factors which contribute to whitefinger
disease are not known, but cold weather, smoking
diseases or physical conditions as well as long
periods of exposure to vibration are mentioned as
factors. In order to reduce the risk of whitefinger
disease, the following precautions are strongly
recommended
a) Keep your body warm. Never use the blower
during rain.
b) Take more than 5 minutes of break in a warm
place frequently.
c) Maintain a firm grip at all times, but do not
squeeze the handles with constant, excessive
pressure.
d) If you feel discomfort, redness and swelling of
your fingers or any other part of your body, see
a doctor before it gets worse.
8. The ignition system of your unit produces an
electromagnetic field of a very low intensity. This field
may interfere with some pacemakers. To reduce the
risk of serious or fatal injury, people with pacemaker
should consult their physician and the pacemaker
manufacturer before operating this tool.
WORKING CIRCUMSTANCE
1. To reduce the risk of injury
associated with exhaust fume
inhalation, do not operate in
unventilated area. The exhaust
gases contain harmful carbon
monoxide.
2. Avoid using the blower where
stable footing and balance are
not assured.
3. Never operate the machine in high wind, bad
weather, potentially explosive atmosphere, when
visibility is poor or in very high or low temperatures.
(Our recommended use environment is below 40
degrees C (104 degrees F).)
AVOID NOISE PROBLEM
NOTE
Check and follow the local regulations as to
sound levels and hours of operations for blower.
1. Operate power equipment only at reasonable hours,
not early in the morning or late at night when people
might be disturbed. Comply with times listed in local
ordinances.
2. To reduce sound levels, limit the number of pieces of
equipment used at any one time.
3. Operate power blowers at the lowest possible throttle
speed to do the job.
4. Check your equipment before operation, especially
the muffler, air intakes and air filters.
WORKING PLAN
To reduce the risk of health damages, avoid excessive
use and take sufficient time to rest .
FUEL
WARNING
To reduce the risk of fire and burn injury:
a) Handle fuel with care. It is highly
flammable.
b) Do not smoke while handing fuel.
c) Do not refuel a hot engine.
d) Do not refuel a running engine.
e) Avoid spilling fuel or oil. Always
wipe unit dry before using.
f ) Move at least 10 ft. (3 meters)
away from the fueling point before starting the
engine.
g) Always store gasoline in a container approved for
flammable liquids.
h) Make sure the unit is properly assembled and in
good operating condition.
i ) Do not use the blower near a fire,
as aiming the blower in the
direction of a flame may cause
flammable substances to ignite.
6
Safety Precautions
English
BEFORE STARTING THE
ENGINE
Each time before starting the engine, inspect the entire
unit to see if every part is in good order and is securely
tightened in place. If any damage is found in the fuel line,
the exhaust line, or the ignition wiring, do not use the
blower until it has been repaired.
IMPORTANT
Before starting operation, always make sure to
check if any obstacles are left inside the volute
case and net. The obstacles may cause serious
injury or damage to fan and volute case.
[130BT]
WARNING
Check to see if the shock-absorbers <A> have
become cracked or otherwise damaged. Note that
failing to replace these rubber and spring mounts
when they have become cracked or damaged may
cause the engine to come loose from its frame during
use, thus resulting in possible serious bodily injury.
If cracked, be sure to replace without delay.
<A>
<B>
[350BT/BF] [370BT/BF]
[380BT/BF]
<A>
<B>
1. This blower is a backpack type, and is shouldered
while operating. It is operated and controlled with
the handle on the tube by right hand.
2. Check the work area that the blower will be used in and
remove or cover all valuables that may be damaged by
the air blast or thrown debris.
3. Make sure you can move and
stand safely. Check the area
around you for possible obstacles
(roots, rocks, branches, ditches,
etc.) in case you have to move
suddenly. Take great care when
working on sloping ground.
4. To reduce the risk of injury
associated with thrown objects.
a) Watch out for children, pets, open windows or
freshly washed cars, and blow debris safely away.
b) Use the full blower tube extension so the air stream
can work close to the ground.
c) Do not allow bystanders in work area.
d) Do not point the
blower tube in the
direction of people
or pets.
e) Always check to
be sure that no
debris has been
blown onto someone else’s property.
f) Pay attention to the direction of the wind, do not
work against the wind.
5. To minimize blowing time.
a) Use rakes and brooms to loosen debris before
blowing.
b) In dusty conditions, slightly dampen surfaces or
use a mister attachment when water is available.
c) Conserve water by using power blowers instead of
hoses for many lawn and garden applications,
including areas such as gutters, screens, patios,
grills, porches and gardens.
6. The blower must not be used while
on a ladder or scaffolding.
<A>
[130BT] [350BT/BF] [370BT/BF]
WARNING
To reduce the risk of injury associated with contacting rotating parts, stop the engine before installing
or removing attachments.
Net <B>
.
Always disconnect the spark plug before performing
maintenance or accessing movable parts.
[380BT/BF]
Never take off the Guard
<A>
USING THE PRODUCT
WARNING
While using the product, if abnormal noise or
vibration occurs, stop the engine immediately and
contact the nearest Husqvarna servicing dealer
for assistance. Checking the fan is very important.
If the rotating fan should break up, it will lead to
serious accidents.
7. Never put the machine down with
the engine running unless you have
it in clear sight.
8. Never touch the spark plug or plug
cord while the engine is in
operation. Doing so may result in
being subjected to an electrical
shock.
9. Never touch the muffler, spark plug,
or other metallic parts of the engine,
or area around the engine cover
while the engine is in operation or
immediately after shutting down the engine. These
metallic parts reach high temperatures during
operation and doing so could result in serious burns.
WARNING
The temperature of the machine may increase after
stopping the engine. Especially never forget to cool
down the engine before refueling the machine.
10. If the engine catches fire or in any other emergency
situation that requires you to free yourself from the
machine, open the buckle in the waist belt and drop the
machine backward.
11. After using blowers and other equipment, CLEAN UP!
Dispose of debris in trash receptacles.
7
Loading...