Husky FS/2 User Manual

Page 1
Please read these instructions
before using your FS/2
TM
HUSKY FS/2
USER LEAFLET
Page 2
USING YOUR FS/2
The FS/2 hand-held computer is rugged and waterproof, but to help ensure trouble-free operation, we recommend that you:
Check how to use your application before
beginning work.
Carry a spare set of batteries
Avoid subjecting your FS/2 to:
unnecessary temperature extremes - bright
sunlight in a vehicle, for example
prolonged immersion in water
physical mistreatment
The FS/2 leaves the factory fitted with non-rechargeable Alkaline batteries and is ready for use. Note: If you fit new rechargeable batteries instead, you must charge the FS/2 before use; please refer to BATTERIES.
20
19
18
17
1a
1
2
3
4
Esc F1 F2 F3 F4
8
7
4
1
0
9
5
6
2
3
.
Del
No
Yes
5
6 7
8
9
10
PgUp PgDn
ABCD
EFGH I J
KLMNOP
11
16
15
QRS T UV
Sp
WXYZ
Clr
14
12
13
Page 3
Note: Keyboard and connector layouts vary on certain models.
1 PORT 1 CONNECTOR: main serial port. 2 PORT 2 CONNECTOR: second serial port. 1a Alternatively, on some models a single connector
is provided, combining PORT 1 and PORT 2.
3 CONTACTS: on the rear of the unit, these
connect to the FS/2 Communications and Charging Rack, if this option is fitted.
4 FUNCTION KEYS: press to use application
functions. 5 POWER KEY: press to turn on or off. 6 HANDSTRAP: on the rear of the unit, this helps
you hold the FS/2 securely. 7 DEL/NO KEY: press to delete entries or answer
No to a question. 8 ENTER/YES KEY: press to complete typing, type
a carriage return, or answer Yes to a question. 9 SHIFT KEYS (S): hold either down to type the
characters (or functions) shown above the keys. 10 BACKLIGHT KEY: press to illuminate the screen
for use in low light. You may need to press at
L
the same time (depending how your FS/2 is set
up). 11 TYPING KEYS: type letters, or symbols and
functions when used with S (SHIFT). 12 BACKSPACE KEY: press to erase typing. 13 PORT 4 CONNECTOR: option. Only fitted if
required to use other options. 14 BATTERY CAP: remove to change batteries. 15 PORT 3 CONNECTOR: for connecting the FS/2
AC Adaptor. 16 SPACE KEY: types a space (blank) character. 17 CURSOR KEYS: move the cursor.
SHIFT U and SHIFT D adjust screen contrast. 18 NUMERIC KEYPAD: type numbers. 19 ESCAPE KEY: usually used to cancel a function. 20 LCD SCREEN: displays prompts and messages
and information as you type.
Page 4
CONTROLS
Note: Your application’s user instructions may
supplement the following information.
Turning on and off
Press P to turn on, or off. To conserve power, the FS/2 turns off automatically if you have not pressed any keys for a short while.
Screen contrast
Adjust the screen contrast for optimum readability, especially at temperature extremes. Hold down either S (SHIFT) key and press U (UP ARROW) to increase contrast or D (DOWN ARROW) to decrease contrast.
Screen backlight
In low ambient light, press C to turn the backlight on. To turn it off, press C again. You may need to press
L
at the same time (depending how your FS/2 is set up). The backlight turns off automatically after a short time, to conserve power.
Date entry
To type numbers or letters, press the appropriate keys. To type a space, press the # (SPACE) key.
To delete characters you’ve just typed, press the B (BACKSPACE) key.
To select the characters or functions shown above the keys, hold down either S (SHIFT) key and then press the appropriate key.
Moving the cursor
Software applications will normally allow you to move the cursor a character or line at a time, using the arrow keys: L, R, U and D. To move the cursor up or down several lines, use U and D.
Page 5
BATTERIES
The FS/2 can be fitted with either rechargeable or replaceable batteries.
The FS/2 batteries are designed to last more than a working shift.
However, if power does run low, a warning BATTERY LEVEL LOW will be displayed. (After a further period of use, your FS/2 will turn itself off and will not turn on again.) You should do one of the following:
Return the FS/2 to your base or office.
Or if rechargeable batteries are fitted, recharge them
(see Charging batteries) or fit a fully charged battery stick (see Replacing batteries).
Or fit three new AA size Alkaline batteries (see
Replacing batteries).
Charging batteries
Charging is recommended before each working shift. You will need an FS/2 AC Adaptor.
CAUTION: DO NOT ATTEMPT TO RECHARGE NON-RECHARGEABLE BATTERIES. Check that rechargeable batteries are fitted to your FS/2, and are oriented correctly. Use only the FS/2 AC Adaptor.
Turn the unit off.
Plug the AC adaptor into the AC supply.
Connect the AC adaptor to Port 3.
Turn on the AC supply.
Leave the unit to recharge, preferably for 8 hours.
Turn off or disconnect from the AC supply.
Alternatively, if your system includes the FS/2 Charging and Communications Rack, you can
recharge a unit by placing it on the Rack.
Page 6
Replacing batteries
Turn your FS/2 off.
Remove the battery cap by using a suitable coin.
Do not allow rain or moisture into the battery
compartment.
Tilt the unit to slide out the batteries.
Slide the fresh batteries into the battery
compartment, positive end first. If you are fitting AA size batteries, it is advisable to fit the packing sleeve supplied with the FS/2.
Refit the battery cap. Seat it with finger pressure
first and make sure that it has engaged the screw threads before tightening it with a suitable coin.
Turn on and check operation.
If you can’t turn on, contact your system provider.
After changing batteries, you MUST ensure that
the battery type, capacity and power management are correctly set. (Refer to your application’s user instructions.)
CAUTION: If you have changed from rechargeable to non-rechargeable batteries, warn anyone you give the unit to. Non-rechargeable batteries must NOT be recharged. Always use batteries of the same type and charge state - don’t mix fresh batteries with used batteries, or rechargeable batteries with non-rechargeable ones. Observe the instructions printed on the battery. Replace only with batteries approved by your FS/2 supplier. DO NOT FIT LITHIUM BATTERIES.
ATTENTION: Dispose of or recycle used batteries according to the manufacturer’s instructions. Nickel-Cadmium rechargeable batteries must be recycled, or disposed of properly.
CAUTION: BATTERY CHEMICAL LEAKAGE IS CORROSIVE. In the unlikely event of battery leakage, do not touch. In case of accidental contact, flush immediately with running water.
Page 7
CLEANING
If the screen gets dirty or smeared, clean it with a clean cloth. If the FS/2 gets very dirty, it should be cleaned:
Make sure that the battery cap is tight. If you
have dropped it, check that the case and seals are intact.
Gently rinse the unit under clean running water
(no more than hand hot, 40˚C). Do not immerse the unit unnecessarily, or use a high pressure jet.
To remove stubborn deposits, use a soft bristle
brush and a mild detergent. TREAT THE KEYBOARD GENTLY.
Blow any water out of the connectors, then leave
it to drain and air dry. DO NOT EXPOSE THE UNIT TO TEMPERATURES ABOVE 55˚C.
Polish the screen with a clean cloth.
CAUTION: Do not use organic solvents or harsh detergents, as they may damage the casing.
PERIPHERALS
CAUTION: Connect only approved cables and peripherals to your FS/2.
To connect a suitable peripheral to the FS/2:
Turn off the FS/2 (and peripheral, if appropriate).
If fitted, remove the protective cap from the
appropriate connector.
Fit the peripheral to the connector.
Use connector locking mechanisms where fitted.
Turn on the FS/2 (and peripheral, if appropriate).
To disconnect a peripheral:
Turn off the FS/2 (and peripheral, if appropriate).
Disconnect the peripheral from the connector.
If provided with a protective cap, fit it to the
connector.
Page 8
PROBLEMS
If you have problems with the FS/2, TELL YOUR SYSTEM PROVIDER, but here are a few quick checks:
If the unit will not turn on, check the batteries’
orientation and try a fresh set of batteries.
If you cannot read the display, try adjusting the
screen contrast: hold down either S (SHIFT) key and press U or D.
If you drop the unit and it stops working, try
turning off and on, and check the batteries.
Your application may provide a RESET facility.
If the unit is very dirty or wet, clean it as
described in CLEANING.
CAUTION: There are no user serviceable parts inside the FS/2. Do not attempt to open.
Electromagnetic Compatibility
The FS/2 complies with EN55022 Class B. This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
If the FS/2 does cause harmful interference, turn it off and consult your dealer or technician for help.
The FS/2 must only be used with approved peripherals and approved A.C. adaptors; shielded communications cables must be employed.
Changes or modifications could void the user’s authority to operate the equipment.
Printed in England P-2240-0010 Copyright 1993 Husky Computers Ltd Issue 1
Loading...