Husky Diesel, High Volume Owner's Manual

Recommended Installation, Maintenance

and Inspection Instructions

Conventional / High-Flow / Diesel Swivels

Model #
0087

0087W
0095

0350
0350W

0352
0352W

0355
0356

2272
2950

3395
3895

3898
4860

5235
5240

WARNING Designed for use at motor fuel dispensing facilities only.

5265
5266

INSTALLATION INSTRUCTIONS

NOTE: Always adhere to installation / usage instructions and warning. Improper use may result in injury, damage or
hazardous spill.

1. Turn off dispenser and relieve line pressure.

2. Use pipe thread sealant (not Teon tape) approved for gasoline on the male
threads of hose section.

3. Install at either the nozzle or dispenser.

4. Tighten approximately 1 or 2 turns past hand tight - do not overtighten.

5. Pressurize system and visually inspect for leaks.

VERIFY SMOOTH ROTATION OF ALL SWIVEL JOINTS AFTER INSTALLATION.

DO NOT OVERTIGHTEN

IF DRIVE OFF OCCURS

• Turn off dispenser and relieve line pressure.

• Inspect the entire dispensing system for damage.

• Check for leaks.

• Check for smooth rotation of all swivel joints.

• Measure gap at joint - if a credit card ts in the gap (0.03 in / 0.76 mm) do not

reinstall.

• Check for electrical conductivity.

SWIVELS

TESTING / MAINTENANCE / INSPECTION

Daily

• Check for leaks / stains

• Check for damage

• Check for smooth rotation of
all swivel joints.

Monthly

• Measure gap at joint - a credit
card should not t in the gap
(0.03 in / 0.76 mm).

• Check "remove after" date.

Annually

• Check for electrical
conductivity.

Husky Corporation • 2325 Husky Way • Pacic, MO 63069 • Phone: [phone] • Fax: [phone] • www.husky.com

• All drive aways, maintenance and
inspection activities must be logged
using the serial number of the
individual product.

• Apply city, state, or federal testing
regulations as appropriate.

ANY TEST / INSPECTION
FAILURE REQUIRES IMMEDIATE
EQUIPMENT REPLACEMENT OR

REMOVAL FROM SERVICE.

MADE IN THE USA

Page 1 009056-12 9/2010

ALWAYS ADHERE TO INSTALLATION / USAGE INSTRUCTIONS AND WARNINGS.

Improper use may result in injury, damage, or hazardous spill.

GENERAL WARNINGS / INSTRUCTIONS

• Use of equipment is at individuals’ own risk.

• Always abide and adhere to city, state, and

federal regulations regarding use and

installation of dispensing equipment.

• Always follow the product manufacturer ’s

installation and maintenance instructions.

• Always turn off all power to dispenser during

maintenance and inspection activities.

• Always close the shear valves during

maintenance and inspection activities.

• Always relieve pressure from system prior to

performing maintenance activities.

• Always check continuity after installation using

a megohmeter (Refer to PEI RP 400

for details).

• Always replace or remove from service

damaged or leaking dispensing equipment

immediately.

• Always report leaks / spills / accidents to

appropriate authorities.

• Always wear appropriate safety equipment

during maintenance activities.

• Always have appropriate re extinguishing

equipment within 5 ft / 1.5 m of dispensers.

• Always use pipe sealant approved for

gasoline service.

• Always place containers on the ground

before lling.

• Always discharge static electricity before

using or servicing equipment by touching

a metal part of the dispenser before and

after fueling vehicle.

• Never smoke within 20 ft / 6.1 m of dispensers.

• Never keep in service past recommended life.

• Never leave the nozzle unattended while

dispensing fuel.

• Never use sparking or aming devices within

20 ft / 6.1 m of dispensers.

• Never use power tools near dispensers or

to aid in the installation process.

• Never use cell phone within 20 ft / 6.1 m

of dispensers.

• Never reenter car when fueling vehicle.

• Never allow gasoline to touch eyes or skin.

• Never use at ow rates in excess of

regulatory guidelines.

• Never use at ow rates less than 5 gpm /

18.9 Lpm.

• Never dispense ammable material into

unapproved containers.

• Never dispense fuel without a valid

driver’s license.

Listings:

WARRANTY

VAPOR PRODUCTS – Husky Corporation will, at its option, repair, replace, or credit the purchase price of any Husky

manufactured product which proves upon examination by Husky, to be defective in material and/or workmanship for a period of one (1)

year of installation or fteen (15) months from the manufacture date of shipment by Husky, whichever occurs rst. The warranty period on

repaired or replacement vapor recovery products is only for the remainder of the warranty period of the defective product.

CONVENTIONAL PRODUCTS – Husky Corporation will, at its option, repair, replace, or credit the purchase price of any Husky

manufactured product which proves upon examination by Husky, to be defective in material and/or workmanship for a period of one (1)

year from the manufacture date of shipment by Husky.

Buyer must return the products to Husky, transportation charges prepaid. This warranty excludes the replaceable bellows,

bellows spring assembly, spout assembly and scuff guard, unless (i) damage is obvious when the product is removed from shipping carton

and (ii) the defective product is returned to Husky prior to use. This warranty does not apply to equipment or parts which have been installed

improperly, damaged by misuse, improper operation or maintenance, or which are altered or repaired in any way.

The Warranty provisions contained herein apply only to original purchasers who use the equipment for commercial or

industrial purposes. There are no other warranties of merchantability, tness for a particular purpose, or otherwise, and any other such

warranties are hereby specically disclaimed.

Husky assumes no liability for labor charges or other costs incurred by Buyer incidental to the service, adjustment, repair, return,

removal or replacement of products. Husky assumes no liability for any incidental, consequential, or other damages under any warranty,

express or implied, and all such liability is hereby expressly excluded.

Husky reserves the right to change or improve the design of any Husky fuel dispensing equipment without assuming any

obligations to modify any fuel dispensing equipment previously manufactured.

Husky Corporation • 2325 Husky Way • Pacic, MO 63069 • Phone: [phone] • Fax: [phone] • www.husky.com

Page 2 009056-12 9/2010