Hunter Stoves Parkray ASPECT 5 COMPACT, Parkray ASPECT 5, Parkray ASPECT 7, Parkray ASPECT 8 COMPACT, Parkray ASPECT 8 User Manual

ASPECT 4 / 4 COMPACT

ASPECT 5 / 5 COMPACT

ASPECT 6
ASPECT 7
ASPECT 8

ASPECT 14

WOOD BURNING STOVE MODELS

HUNTERSTOVES.CO.UK

Welcome to the Hunter Stoves family and thank you for

purchasing a Parkray Aspect stove. This stove was designed and

built to be a high-performance heating appliance, and we hope

it will bring you great enjoyment. The natural environment is

important to us, so our stoves are manufactured to provided you

with a clean and efcient burn that will keep you warm through

cold winter nights.

CONTENTS INDEX

STOVE INFORMATION

GENERAL INFORMATION 4/5

MATERIAL CLEARANCES 6

GENERAL GUIDANCE 7 - 10

OPERATING INSTRUCTIONS 11/12

MAINTENANCE AND SERVICING 13 - 14

3

IMPORTANT INFORMATION 15/16

TROUBLESHOOTING 17

WARRANTY INFORMATION 18/19

STOVE INFORMATION

DIMENSIONS H W FD TF RF AC D1 D2

ASPECT 4 515mm 400mm 127mm 110mm 416mm 17.5mm 327mm 410mm

ASPECT 4
COMPACT

ASPECT 5 590mm

ASPECT 5
COMPACT

ASPECT 6 623mm 557mm 127mm 143mm 523mm 2 mm 343mm 422mm

ASPECT 7 550mm 579mm 127mm 110mm 451mm 17.5mm 327mm 410mm

ASPECT 8 623mm 617mm 127mm 128mm. 524mm 7mm 343mm 417mm

ASPECT 8
COMPACT

ASPECT 14 658mm 667mm 127mm

515mm 400mm 127mm 110mm 416mm 17.5mm 277mm 379mm

494mm 127mm 110mm

590mm 494mm 127mm 110mm 491mm 17.5mm 277mm 358mm

648mm 617mm 127mm 153mm

153mm 559mm NA

491mm 17.5mm 327mm 410mm

539mm 13mm 398mm

468mm 555mm

459mm

- 3 -

GENERAL INFORMATION

Meets the requirement of:
European Standard EN-13240
DEFRA (Smoke Control Areas
(UK)

Stove Model Nominal

Heat Output

Aspect 4 4.5kW 81.0% 56kg

Efciency Weight

Aspect 4 Compact

Aspect 5

Aspect 5 Compact

Aspect 6

Aspect 7 5.0kW 81.0% 86kg

Aspect 8 7.5kW 76.0% 110kg

Aspect 8 Compact

Aspect 14

!

The appliance will become very hot when used in
accordance with the instructions. The supplied
operating tool or glove may be used to open the door
and operate the air controls. We also recommend use

of a reguard in the presence of childre, the elderley or
the inrm. The reguard should be manufactured in

accordance with BS8423.

4.5kW 81.0%

5.0kW 80.0%

5.0kW 80.0%

5.0kW 80.0%

7.5kw 76.0%

7.8kW 77%

52kg

79kg

72kg

93kg

110kg

130kg

Competent Persons Scheme

Hunter Stoves Group recommend that this stove be
installed by a member of an accredited competent
persons scheme e.g. HETAS.

If the installer is not a member of a competent person’s
scheme, it is a legal requirement, in the UK, to notify

your Local Building Control Ofcer in advance of any

installation work starting.

Legal Requirements

These instructions cover the basic principles to ensure
satisfactory installation of the stove, although details

may need slight modication to suit particular local

site conditions.

In all cases the installation must comply with
current Building Regulations, Local Authority
Byelaws, European and National Standards and

other specications or regulations as they affect the

installation of the stove.

It should be noted that the Building Regulations
requirements may be met by adopting the relevant
recommendations given in British Standards BS
8303, BS 6461 and BS 7566 as an alternative means
to achieve an equivalent level of performance to that
obtained following the guidance given in Approved
Document J.

Hearth

Hearth constructions must comply with the current
building regulations.

Your stove must be installed on a oor with adequate

load-bearing capacity, otherwise suitable measures
should be taken.

If the existing construction does not meet this
pre-requisite, suitable measures (e.g. load distributing
plate) should be put in place.

The hearth should extend at least 225mm from the
front of the appliance(as per Building Regulations) we
recommend 300 mm.

The stove should stand wholly above a solid,
non-combustible hearth, at least 125 mm thick (this

may include the thickness of a solid oor).

Please refer to Building Regulations Approved
Document J for further information.

- 4 -

Air Supply

Connection to the Chimney

Aspects 4, 4C, 5, 5C, 6 and 7

The room or space containing this appliance does not
need a permanent, unobstructed air opening unless
the air permeability rating is less than or equal to 5m³/
hour/m².

Aspects 8, 8 Compact, 14

The room or space containing this appliance does
need a permanent, unobstructed air opening.

1375mm² - Aspect 8
1540mm² - Aspect 14.

All

If a draught stabiliser is tted, the air opening should

be at least: -

3825mm² (Aspect 4s),
4250mm² (Aspect 5s, 6 and 7)
3625mm² (Aspect 8)
3880mm² (Aspect 14).

Due consideration should be given to air requirements
for any other appliance in the same room or space.

Any air opening must be kept clear from blockage or
obstruction.

New Build

Attention is needed in new built properties where
the design air permeability is less than 5m3/h.m2.
Approved Document J and Appendix F gives further
information. A window opening is not appropriate.

An existing replace opening can be bricked up or
sealed with a register plate. A short length of ue pipe

of minimum 125mm internal diameter may then be

used to connect the stove to the chimney. This ue

pipe should be made of 316 grade stainless steel or
vitreous enamelled steel, nominal thickness 1.2mm.
Ensure that the pipe end is no closer than 76mm to
the chimney walls. The length of any horizontal run of

ue pipe must not exceed 125mm. It is essential that
all connections between the stove and chimney-ue

are sealed and made airtight. Any bend in the chimney

or connected ue pipe should not exceed 45

bends should not be used.

Ensure any existing chimneys are clear of obstruction
and have been swept prior to installation. If the stove

is being tted into a previous open replace then the
chimney must be swept one month after tting.

Make provision to access the chimney/ue system for

cleaning and the removal of debris. If there is no
existing chimney then either a prefabricated block
chimney in accordance with Building Regulations
Approved Document J, or a twin-walled insulated

stainless-steel ue to BS4543 can be used. These
chimneys must be tted in accordance with the

manufacturer’s instructions and Building Regulations.

New masonry and ue block chimneys must meet

the requirements of Building Regulations Document

J. Any connecting ue pipe systems must also meet

these regulations.

Please check the suitability of the replace and/or

surround for use with this appliance before installing
it. If you have any doubts about the suitability of
your chimney, consult your local Dealer/Stockist or
Installation Engineer.

0

and 90

0

Certicate of Compliance

After completionof the appliance instalation please
ensure the form below (specimen) is completed by your
installer to comply with the requirements of HETAS and
building regulations. The installer must supply these
details, including registration number for any insurance
details that may need changing after installation of the
appliance.

- 5 -

MATERIAL CLEARANCES

Hearth Requirements

Combustible/Non Combustible Distances

Model A (to Twin-

Walled

Flue)

Aspect 4 125mm 500mm 500mm

Aspect 4 Compact 125mm 500mm

Aspect 5 125mm 600mm 600mm 50mm 50mm 500mm 1230mm

Aspect 5 Compact 125mm 600mm 600mm 50mm 50mm 500mm 1230mm

Aspect 6 125mm 600mm 600mm 50mm 50mm 500mm 1230mm

Aspect 7 125mm 500mm 500mm 50mm 50mm 500mm 1230mm

Aspect 8 Compact 100mm 375mm 375mm 50mm 50mm 600mm 1200mm

Aspect 8 100mm 375mm 375mm 50mm 50mm 600mm 1200mm

Aspect 14 100mm 525mm 525mm 50mm 50mm 650mm 1500mm

For clearance distances for the single skin ue pipe please refer to Building Regulations Document J.

B

CombustibleCCombustible

500mm 50mm 50mm

B

Non

Combustible

50mm 50mm 500mm

C

Non

Combustible

Superimposed

Hearth

500mm 1230mm

D

Front

to

Furniture

1230mm

- 6 -