Table of Contents
www.HunterFan.com
1.888.830.1326
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or ofce for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
What to Expect with
Your Installation
2
Preparation
6
Blades Troubleshooting
Tools Needed
PAG E
Downrod
PAG E
Switch Housing
3
7
Mounting Options
PAG E
Wiring Canopy
PAG E
Maintenance &
Cleaning
4
10
Ceiling Bracket
PAG E
PAG E
?
PAG E
5
PAG E
11
?
PAG E
12
13
1
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company
PAG E
15
PAG E
?
PAG E
16
What to Expect with Your Installation
www.HunterFan.com
1.888.830.1326
Must be able to
secure the fan to
building structure or
fan-rated outlet box
You may need a
friend to help you.
Check box to see
fan weight
If you are unfamiliar
with wiring, use a
qualied electrician.
Know your wiring
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Assess ceiling angle
30 inches
from blade tip
to nearest wall
or obstruction
Assess location
Standard Downrod
1
for ceilings 8-10 feet high
Shorter Downrod
2
for fans installed close to ceiling
Longer Downrod
3
for ceilings 10 feet or higher
Select a downrod length
7 feet
from bottom
edge of blade
to the oor
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
w.1 - To reduce the risk of re, electrical shock, or
personal injury, mount fan directly from building
structure and/or an outlet box marked acceptable for
fan support of 70 lbs (31.8 kg) and use the mounting
screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing
or servicing your fan, disconnect the power by turning
off the circuit breakers to the outlet box and associated
wall switch location. If you cannot lock the circuit
breakers in the off position, securely fasten a prominent
warning device, such as a tag, to the service panel.
w.3 - To reduce the risk of re, electrical shock, or motor
damage, use only Hunter Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the
blade brackets when installing the blade brackets, balancing
the blades, or cleaning the fan. Do not insert foreign objects
in between rotating fan blades.
CAUTIONS
c.1 - All wiring must be in accordance with national and
local electrical codes ANSI/NFPA 70. If you are unfamiliar
with wiring, use a qualied electrician.
c.2 - Use only Hunter replacement parts.
2
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company
Tools Needed
www.HunterFan.com
1.888.830.1326
Ladder
Pliers Wire Strippers
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
9/64” Drill Bit
(optional)
3
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company
Screwdrivers
O
34
CEILING
Mounting Options
www.HunterFan.com
1.888.830.1326
OPTION
If you have a at ceiling:
WALL
Hang your fan by a standard downrod (included) .
Standard
Mounting
1
Support
Structure
Support
Structure
OPTION
If you have an angled ceiling:
1. You will need a longer downrod (sold separately) .
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately) .
Use the three steps below to determine if your ceiling angle is greater than 34°
Angled
Mounting
2
Standard
Mounting
Style
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
Ceiling
Outlet Box
(required)
FOLD
on dotted line
1
N
O
I
T
A
U
T
I
S
1
34°
Guide Touches
BOTH Ceiling & Wall
You need ONLY
a Longer
Downrod
*most common
2 3
PLACE
against wall
2
N
O
I
T
A
U
T
I
S
Guide Touches
but NOT Ceiling
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
SLIDE
toward ceiling
Wall
4
4
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company
Use Standard Mounting
or Low-Prole Mounting
to hang the fan from a at ceiling.
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
Ceiling Bracket
Turn Power
OFF
www.HunterFan.com
For angled ceilings, point
opening toward peak.
1.888.830.1326
Make sure all four bumpers are
still attached.
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
Use wood screws
(included) when securing
to support structure with
approved electrical outlet
box. Drill 9/64” pilot holes
in support structure to aid
in securing ceiling bracket
with hardware found in
the hardware bag.
5
5
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company
Use machine screws
(provided with outlet
box) when securing to
existing ceiling fan-rated
outlet box. Make sure
it is securely installed
and is acceptable for fan
support of 31.8 kg (70 lbs)
or less.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Refer to warning w.1 on pg. 2
Ceiling Bracket (continued)
Preparation
Time Saver Tip: Get a helper
to insert grommets, found in
the hardware bag, into the
blades while you’re doing the
next couple of steps.
www .Hunt erF an.c om
www.HunterFan.com
E
E
P
K
!
D
I
S
C
A
Remove the shipping blocks from the
motor. Save the screws. They will be
needed for blade iron installation.
Note: Some fans will have a shipping
ring instead of shipping blocks. Please
remove the ring and save the screws.
R
D
1.888.830.1326
1.888.830.1326
6
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company
Downrod
www.HunterFan.com
1.888.830.1326
Standard
Downrod
for ceilings 8-10’ high
Option 1 Option 2
Shorter
Downrod
for fans installed
close to ceiling
Included
(pre-assembled)
Longer
Downrod
for angled
ceilings or
Option 3
ceilings 10’ or
higher
skip to next page
If you need a different downrod length follow these steps:
Steps 1-5 to remove standard downrod pipe
1 2 3 4 5
Slide
Slide
6 7 8 9 10
Included
Sold Separately
Steps 6-10 to reassemble with new pipe
7
7
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company
Downrod (continued)
www.HunterFan.com
1.888.830.1326
KEEP!
E
E
P
K
!
Remove the pre-installed
setscrew so that the downrod
can be inserted.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
8”
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company
3/8”
T
U
C
P
I
R
T
S
&
8”
(not to scale)
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
3/8”
If the setscrew is not tightened
securely, the fan may fall.
8
8
Downrod (continued)
DO NOT PICK THE FAN UP BY THE
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
www.HunterFan.com
1.888.830.1326
of the fan.
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
9
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company
Wiring
Note: To connect the wires, hold the bare metal
www.HunterFan.com
1.888.830.1326
leads together and place a wire connector over
E
C
I
L
I
M
N
O
R
F
G
them, then twist clockwise until tight.
E
C
I
L
I
M
N
O
R
F
G
F
A
M
N
O
R
F
Refer to CAUTION c.1 on pg. 2
Green/Yellow
Stripe
F
R
O
M
C
E
(Grounding)
Green/Yellow
Stripe
I
L
I
(Grounded)
White
Using an orange wire
connector from
the hardware bag,
connect the 3 grounding
wires (green, green/
yellow stripe, or bare
copper) coming from the
T
E
K
C
A
R
B
G
N
ceiling, downrod, and
hanging bracket.
F
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
(Ungrounded)
Black
Blue
Using the orange wire
connectors from
the hardware bag, connect
the black wire (ungrounded)
from the ceiling to the black
and the blue wires from the
fan. Connect the white wire
(grounded) from the ceiling to
the white wire from the fan.
R
O
N
A
F
M
10
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company
Canopy
Screw
Holes
www.HunterFan.com
1.888.830.1326
Position the canopy so that, when
lifted into place, the canopy ts into
the hanging bracket as shown.
Lift the canopy into place so that
the screw holes are aligned.
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company
Insert the two canopy screws
found in the hardware bag.
Note: Fan style may vary.
11
Blades
Insert grommets found in the hardware
Remember the screws that
you kept after removing the
shipping blocks (page 6)? You
need them for this step.
www.HunterFan.com
1.888.830.1326
bag into the holes in the blades, then
secure each blade to a blade iron with
screws found in the hardware bag.
Lightly attach the blade irons to the
motor with the blade iron armature
screws, then securely tighten after both
screws are attached.
12
12
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company
Switch Housing
www.HunterFan.com
1.888.830.1326
Screw two housing assembly screws
from the hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
13
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company
Insert the third screw, found in
the hardware bag, into place and
then tighten all three screws.
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the switch
housing xture falling.
Switch Housing (continued)
www.HunterFan.com
1.888.830.1326
Connect the plugs from the upper and
lower switch housings. Make sure to line up
the colored markings on the connectors.
Lift the lower switch housing until its
screw holes are aligned with the screw
holes in the upper switch housing. Install
the three switch housing screws, found
in the hardware bag. Tighten all
three screws.
14
14
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company
Attach the pull chain pendant to the short
chain coming from the switch housing.
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
assembly screws could result in the light xture falling.
Switch Housing (continued)
CONGRATUALTIONS!
YOU’RE DONE!
Maintenance & Cleaning
Turn Power
ON
Reverse
Switch
www.HunterFan.com
1.888.830.1326
Changing the direction of air
ow - move the reverse switch
to the opposite position.
15
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company
Cleaning the fan - use soft
brushes or cloths to prevent
scratching. Cleaning products
may damage the nishes.
Troubleshooting
www.HunterFan.com
1.888.830.1326
Fan doesn’t work
• Make sure power switch is on.
• Pull the pull chain to make sure
it is on.
• Push the motor reversing switch
rmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 10.
• Check the plug connection in
the switch housing.
Excessive wobbling
• Tighten all of the blade and
blade iron screws until they
are snug.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• Use the provided balancing
kit and instructions to balance
the fan.
Noisy Operation
• Tighten the blade and blade
iron screws until they are snug.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
16
M0049-01 • 09/11/15 • © 2012–2015 Hunter Fan Company