Hunter Fan Co. B2255842, B2255872 User Manual

Download

30 inches

7 feet

Ladder

Table of Contents

www.HunterFan.com

1.888.830.1326

Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance

in your home or ofce for many

years. This installation and operation manual contains complete instructions for installing and operating your fan.

We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world.

To register your fan, please visit:

www.HunterFan.com/register

Save your receipt for proof of purchase.

Switch Housing Light Kit

What to Expect with

Your Installation

Hanging the Fan

Tools Needed

PAG E

Remote Control

Wiring

Ceiling Plate

PAG E

Canopy

PAG E

Operation,

Maintenance & Cleaning

Top Housing

PAG E

Blades

PAG E

Troubleshooting

PAG E

What to Expect with Your Installation

If you are unfamiliar with wiring, use a

qualied electrician.

Must be able to secure the fan to building structure or fan-rated outlet box

You may need a friend to help you.

Check box to see fan weight

Know your wiring

30 inches

from blade tip to nearest wall or obstruction

7 feet

from bottom

edge of blade

to the oor

Assess location

www.HunterFan.com

1.888.830.1326

Read and Save These Instructions

This product conforms to UL Standard 507.

WARNINGS

w.1 - To reduce the risk of re, electrical shock, or personal injury,

mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.

w.2 - To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.

w.3 - To reduce the risk of re, electrical shock, or motor damage, use only Hunter Solid State Speed Controls.

w.4 - To reduce the risk of personal injury, do not bend the blade brackets when

installing the blade brackets, balancing the blades, or cleaning the fan. Do not

insert foreign objects in between rotating fan blades.

CAUTIONS

c.1 - All wiring must be in accordance with national and local electrical codes

ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualied electrician.

c.2 - Use only Hunter replacement parts.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: modications not approved by the party responsible for compliance

could void user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Tools Needed

www.HunterFan.com

1.888.830.1326

Ladder

Pliers Wire Strippers

Power Drill

(optional)

If mounting to a support structure, you will also need these tools.

9/64” Drill Bit

(optional)

Screwdrivers

Ceiling Plate

Turn Power

OFF

Bumper

Make sure all four bumpers are

still attached.

Use wood screws (included) when securing

to support structure with approved electrical

outlet box. Drill 9/64” pilot holes in support

structure to aid in securing ceiling plate with

hardware found in the hardware bag.

www.HunterFan.com

1.888.830.1326

To avoid possible electrical shock, before installing your fan,

disconnect the power by turning off the circuit breakers to the

outlet box associated with the wall switch location.

Refer to warning w.1 on pg. 2

Top Housing

Adapter

Trim Ring

www.HunterFan.com

Canopy

Adapter

1.888.830.1326

Thread the wires through the

top housing.

Place the top housing onto the

motor housing so that the holes

in the top housing lineup with

the holes in the motor housing

and the adapter.

Rest the trim ring on the top

housing.

Place the canopy on the top

housing. Ensure all four screw

holes line up with the screw

holes in both the top housing

and the adapter.

Top Housing (continued)

www.HunterFan.com

1.888.830.1326

Top Housing

Screws

Grounding

Screw

Install the top housing screws. Install

the grounding screw in the smaller

screw hole. These screws can be found

in the hardware bag.

3/8”

8”

(not to scale)

The wires can be cut, but leave at

least 8” extending from the top of

the canopy.

8” 3/8”

Hanging the Fan

Ceiling Plate Hook

www.HunterFan.com

1.888.830.1326

Raise the fan and align the slots in the

canopy with the hooks on the ceiling plate.

Note: To hang the fan, you must tilt the

canopy to an almost vertical position so that

the canopy slots sit on the ceiling plate hooks.

Place the slots over the ceiling plate

hooks to hang the fan.

Note: Fan style may vary.

Wiring

Using an orange

yellow stripe, or bare

from the ceiling and

ceiling plate.

Receiver

Note: To connect the wires, hold the bare metal leads together and place a wire connector over them,

then twist clockwise until tight.

wire connector from

the hardware

bag, connect the

3 grounding wires

copper) coming

(green, green/

www.HunterFan.com

green

green/yellow stripe

(grounding)

1.888.830.1326

Refer to CAUTION c.1 on pg. 2

Place the receiver inside the canopy

Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of

the outlet box and the ungrounded wires on the other side of the outlet box.

Using the orange wire connectors from the remote control hardware bag:

• Connect the yellow wire from the receiver to the black wire from the fan.

• Connect the blue wire from the receiver to the blue wire (or possibly black with white stripe wire) from the fan.

www.HunterFan.com

yellow

blue

Using the orange wire connectors from the hardware bag:

• Connect the black (ungrounded)

black

(ungrounded)

white (grounded)

1.888.830.1326

wire from the ceiling to the black wire from the receiver.

white

• Connect the white (grounded)

black

blue

wire from the ceiling to both the

black

white

white wire from the receiver and the white wire from the fan.

Refer to CAUTION c.1 on pg. 2

Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of

the outlet box and the ungrounded wires on the other side of the outlet box.

Canopy

Canopy Screw

www.HunterFan.com

Ceiling

Plate Hooks

1.888.830.1326

Screw

Holes

Swing the fan up to align the canopy

screw holes with the mounting holes on

the ceiling plate.

Note: The slots in the canopy must

remain engaged while swinging the

canopy for alignment.

Hold the canopy up with the screw

holes aligned. Partially install two

canopy screws, found in the

hardware bag, into the holes opposite

the ceiling plate hooks.

Canopy Screw

Partially install a canopy screw, found

in the hardware bag, between the

ceiling plate hooks. When all the holes

are properly aligned, securely tighten all

three canopy screws.

Canopy (continued)

Canopy

Trim Ring

www.HunterFan.com

1.888.830.1326

Using both hands, push the canopy trim ring up

to the top of the canopy. The canopy trim ring will

snap and lock into place.

Note: Should you need to remove the trim ring,

press rmly on opposite sides of the trim ring. The

tabs will ex out releasing the canopy trim ring.

Blades

www.HunterFan.com

1.888.830.1326

Attach each blade to a blade iron using three

blade washers, found in the hardware

bag, and three blade assembly screws, found

in the hardware bag.

Switch Housing

www.HunterFan.com

1.888.830.1326

Screw two housing assembly screws from

the hardware bag halfway into the

motor housing. It does not matter which

two screw holes you choose.

Feed the wire plug through the center

hole of the upper switch housing, then

wrap keyhole slots around the screws and

twist counterclockwise.

Insert the third screw, found in the

hardware bag, into place and then tighten

all three screws.

Make sure the upper switch housing is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch

housing xture falling.

Light Kit

www.HunterFan.com

1.888.830.1326

Screw two housing assembly screws from

the hardware bag halfway into the

upper switch housing. It does not matter

which two screw holes you choose.

Connect the plugs from the upper

and lower switch housings. Make sure

to line up the colored markings on

the connectors.Wrap light kit keyhole

slots around the screws and twist

counterclockwise.

Install the third switch housing screw.

Tighten all three screws securely.

Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all three

assembly screws could result in the light xture falling.

Light Kit (continued)

Tab

Notch

www.HunterFan.com

1.888.830.1326

Install a bulb into each of the sockets.

When necessary, replace with bulbs of the

same type and wattage.

Lift the globe and align the notches in the

globe with the tabs in the light kit. Attach

the glass bowl to the light kit by twisting it

clockwise until it snaps into place.

Remote Control

www.HunterFan.com

1.888.830.1326

Battery Door

Phillips Head Screw

To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The

battery should be installed with the positive

(+) side up. Replace with a CR2032 battery

when necessary.

Switch Cover Plate

Removed Tabs

To install the transmitter cradle, remove the

two screws holding the switch cover plate. Do

not remove the cover plate. Orient the cradle

by lining up the two mounting holes with

those on the cover plate. Insert and tighten

the screws. Do not over tighten.

Note: For rocker-style cover plates, break off

the tabs by pushing outward.

Rocker- Style

Plate

Turn Power

CONGRATULATIONS!

YOU’RE DONE!

See next page for fan operation instructions.

Operation, Maintenance, & Cleaning

Medium

Speed

Fan Off

High

Speed

www.HunterFan.com

1.888.830.1326

Low

Light

Speed

To turn on fan, press a fan speed button.

Speeds range from off (0) to high (3). Quickly

press the Light button to turn the lights off

and on. Hold the Light button to raise and

dim the light level.

The remote transmitter should already be paired

to the receiver and ready to use.

Note: If your need to pair your remote, turn fan

power off and back on at the wall switch. Within 3

minutes, press and hold both the Fan Off button

and the High button for 4 seconds to pair the remote. To prevent faulty operation, please

ensure all other ceiling fans within range are

turned off at the wall switch while pairing.

Reverse Switch

To switch the direction of air ow, move the

reverse switch to the opposite position. You

will need to remove the glass to do so.

Operation, Maintenance, & Cleaning (continued)

www.HunterFan.com

1.888.830.1326

Safe-Exit

The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out. To use Safe-Exit:

• Press the Fan Off button for at least three seconds to initiate the Safe-Exit Mode.

• The lights will ash for visual

conrmation.

• The lights will stay on 50% brightness for 15 seconds and then begin to dim. After a total of 30 seconds, the lights will be completely off.

Changing the bulbs - carefully

remove the globe. Unscrew bulbs

and replace with bulbs of the same

wattage. Reinstall the globe.

When cleaning the fan, use soft brushes

or cloths to prevent scratching. Cleaning

products may damage the nishes.

Troubleshooting

www.HunterFan.com

1.888.830.1326

Fan doesn’t work

• Make sure power switch is on.

• Pull the pull chain to make sure it is on.

• Push the motor reversing switch

rmly left or right to ensure that

it is engaged.

• Check the circuit breaker to ensure the power is turned on.

• Make sure the blades spin freely.

• Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram on pages 9-10.

• Check the plug connection in the switch housing.

Excessive wobbling

• Tighten all of the blade and blade iron screws until they are snug.

• Turn the power off, support the fan carefully, and check that the hanger ball is properly seated.

• Use the provided balancing kit and instructions to balance the fan.

Remote control of fan is erratic

• Make sure the battery is installed correctly.

• Install a fresh battery.

Transmitter only works when held at close range

• Change battery.

Noisy operation

• Tighten the blade and blade iron screws until they are snug.

• Check to see if any of the blades are cracked. If so, replace all of the blades.

If you have multiple remotes or multiple remote-controlled fans installed on the same circuit breaker and you are experiencing

interference or faulty operation of your remote controls, please go to www.HunterFan.com/FAQs and click “How do I properly install multiple remote-controlled fans?” for information on how to correct this issue.

Lights dim when turned on or do not turn on at all.

• Make sure the wattage of the light bulbs installed matches

the specications on the light

sockets.

Hunter Fan Co. B2255842, B2255872 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual