Hunter Fan Co. B2113031, B2113029, B2113048 User Manual

30 inches
7 feet
Ladder
Table of Contents
www.HunterFan.com
1.888.830.1326
Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance
in your home or ofce for many
years. This installation and operation manual contains complete instructions for installing and operating your fan.
We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
What to Expect with
2
Hanging the Fan
6
Switch Housing
Tools Needed
PAG E
Wiring
PAG E
Maintenance,
Operation & Cleaning
3
7
Ceiling Bracket
PAG E
Motor Housing
PAG E
Troubleshooting
?
?
4
8
Preparation
PAG E
PAG E
5
Blades
PAG E
PAG E
9
PAG E
10
PAG E
12
1
M0047-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
?
PAG E
13
What to Expect with Your Installation
www.HunterFan.com
1.888.830.1326
1.888.830.13261.888.830.1326
Must be able to secure the fan to building structure or fan-rated outlet box
You may need a friend to help you.
Check box to see fan weight
If you are unfamiliar with wiring, use a
qualied electrician.
Know your wiring
30 inches
from blade tip to nearest wall or obstruction
Assess location
7 feet
from bottom
edge of blade
to the oor
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
w.1 - To reduce the risk of re, electrical shock, or
personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
w.3 - To reduce the risk of re, electrical shock, or motor damage, use only Hunter Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade brackets when installing the blade brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
CAUTIONS
c.1 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar
with wiring, use a qualied electrician.
c.2 - Use only Hunter replacement parts.
2
M0047-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
Tools Needed
www.HunterFan.com
1.888.830.1326
Ladder
Screwdrivers
If mounting to a support structure, you will also need these tools.
Power Drill
(optional)
3
M0047-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
9/64” Drill Bit
(optional)
Ceiling Bracket
Turn Power
Bumper
www.HunterFan.com
1.888.830.1326
OFF
To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to the
outlet box associated with the wall switch location.
Make sure all four bumpers are still attached.
4
M0047-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
Use wood screws (included) when securing to support structure with approved electrical outlet
box. Drill 9/64” pilot holes in support structure to aid in securing ceiling bracket
with hardware found in
the hardware bag.
Use machine screws
(provided with outlet
box) when securing to
existing ceiling fan-rated
outlet box. Make sure
it is securely installed
and is acceptable for fan
support of 31.8 kg (70 lbs)
or less.
Refer to warning w.1 on pg. 2
Ceiling Bracket (continued)
Preparation
www.HunterFan.com
www.HunterFan.com
Time Saver Tip: Get a helper
to insert grommets, found in
the hardware bag, into the
blades while you’re doing the
next couple of steps.
1.888.830.1326
1.888.830.1326
5
M0047-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
Hanging the Fan
Ground
Wire
www.HunterFan.com
1.888.830.1326
While holding the wires out of the way, lift
the motor assembly and place the square
hanger into the opening in the ceiling
bracket. Be sure the ground wire attached
to the hanger faces out of the large
opening in the ceiling bracket.
Screw Hole
Once the motor is in the ceiling
bracket, use the two locking screws
found in the hardware bag to secure
the motor to the ceiling bracket.
Locking
Screw
6
M0047-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
Note: Fan style may vary.
Wiring
Using an orange wire
connect the 3 grounding
www.HunterFan.com
1.888.830.1326
Note: To connect the wires,
E
C
I
L
I
M
O
R
F
N
G
hold the bare metal leads together and place a wire
E
C
I
L
M
I
O
R
F
N
G
connector over them, then twist
clockwise until tight.
M
O
R
F
Refer to CAUTION c.1 on pg. 2
Green/Yellow Stripe
(grounding)
F
A
N
Black (ungrounded)
White (grounded) White
Using the orange
Green/Yellow Stripe
F
R
O
M
C
E
I
L
Green/Yellow Stripe
I
N
connector from
the hardware bag,
Blue
Black
wires (green, green/
yellow stripe, or bare
copper) coming from
the ceiling, fan, and
hanging bracket.
T
E
K
C
A
R
B
G
Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
F
R
O
M
N
A
F
wire connectors from
the hardware bag,
connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the
fan. Connect the white
wire (grounded) from
the ceiling to the white
wire from the fan.
7
M0047-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
Motor Housing
Indentation
Notch
Screw
Holes
Motor
Housing
Screw
www.HunterFan.com
1.888.830.1326
Raise the motor housing up over the motor and ceiling bracket. Turn the motor housing so the screw holes align and the indentation
in the housing locks into place with the notch
in the ceiling bracket. The motor housing is
not secured until the next step is complete.
Do not leave unattended.
With a Phillips head screwdriver, install
the four motor housing screws found
in the hardware bag. Tighten all four
screws securely.
8
M0047-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
Blades
Insert grommets found in the hardware
Lightly attach the blade irons to the
www.HunterFan.com
1.888.830.1326
bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag.
motor with screws found in
the hardware bag, then securely
tighten after both screws are attached.
9
M0047-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
Switch Housing
www.HunterFan.com
1.888.830.1326
Screw two housing assembly screws
from the hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
10
M0047-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
Insert the third screw, found in
the hardware bag, into place and
then tighten all three screws.
Make sure the upper switch housing is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch
housing xture falling.
Switch Housing
www.HunterFan.com
Turn Power
ON
1.888.830.1326
Partially install two of the
switch housing screws found in
the bag. Connect the plugs
from the upper and lower switch
housings. Make sure to line up
the colored markings on the
plug connectors.
Align the notches in the sides of
the lower switch housing with
the screws on the upper switch
housing. Twist the lower switch
housing clockwise to lock into
place. Install the third switch
housing screw. Tighten all three
screws securely.
11
M0047-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
Connect the fan pull chain
pendant to the short chain
coming from the switch housing.
Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all three
assembly screws could result in the light xture falling.
Switch Housing (continued) Maintenance, Operation & Cleaning
CONGRATULATIONS!
YOU’RE DONE!
The pull chain controls the fan:
from high to off.
Changing the direction of air
ow - move the reverse switch
to the opposite position.
Reverse
Switch
www.HunterFan.com
Cleaning the fan - use soft
brushes or cloths to prevent
scratching. Cleaning products
may damage the nishes.
1.888.830.1326
12
M0047-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
Troubleshooting
www.HunterFan.com
1.888.830.1326
Fan doesn’t work
Make sure power switch is on.
Pull the pull chain to make sure
it is on.
Push the motor reversing switch rmly left or right to ensure that
it is engaged.
Check the circuit breaker to ensure the power is turned on.
Make sure the blades spin freely.
Turn off power from the circuit
breaker, then loosen the canopy and check all the connections according to the wiring diagram on page 7.
Check the plug connection in the switch housing.
Excessive wobbling
Tighten all of the blade and blade iron screws until they are snug.
Use the provided balancing kit and instructions to balance the fan.
Noisy Operation
Tighten the blade and blade iron screws until they are snug.
Check to see if any of the blades are cracked. If so, replace all of the blades.
13
M0047-01 • 06/25/15 • © 2012–2015 Hunter Fan Company
Loading...