Hunter Fan HTF3482 Owner Manual

Download

Page 1

ENGLISH

www.HunterFanInternational.com

MB521-01 • 03/18/15 • © Hunter Fan Company

Page 2

Before installation and usage of this product, please read this

manual and keep it for future reference.

Page 3

30 inches

7 feet

Ladder

Table of Contents

www.HunterFanInternational.com

Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance

in your home or ofce for many

years. This installation and operation manual contains complete instructions for installing and operating your fan.

We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world.

Blades Troubleshooting

What to Expect with

Your Installation

Motor Housing

Switch Housing

& Light Kit

Tools Needed

PAG E

Downrod

Globe

Mounting Options

PAG E

Wiring Canopy

PAG E

Maintenance

& Cleaning

Ceiling Bracket

PAG E

MB521-01 • 03/18/15 • © Hunter Fan Company

Page 4

What to Expect with Your Installation

If you are unfamiliar with wiring, use a

qualied electrician.

Must be able to secure the fan to building structure or fan-rated outlet box

You may need a

friend to help you.

Check box to see fan weight

Know your wiring

Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.

Assess ceiling angle

,8 Meters (30 inches)

from blade tip to nearest wall or obstruction

Assess location

Standard Downrod

for ceilings 2,4-3 m (8-10 feet) high

Shorter Downrod

for fans installed close to ceiling

Longer Downrod

for ceilings 3 m (10 feet) or higher

Select a downrod length

2,1 Meters

(7 feet)

from bottom

edge of blade

to the oor

www.HunterFanInternational.com

Read and Save These Instructions

This product conforms to UL Standard 507.

WARNINGS

w.1 - To reduce the risk of re, electrical shock, or personal

injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.

w.2 - To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.

w.3 - To reduce the risk of re, electrical shock, or motor damage, use only Hunter Solid State Speed Controls.

w.4 - To reduce the risk of personal injury, do not bend the blade brackets when installing the blade brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

w.5 - This product is not intended to be used by people (including children) whose physical, sensory, or mental capacities are different or diminished, or lack of experience or knowledge, unless such persons receive training or work under supervision of a person responsible for their safety.

w.6 - Children should be supervised to ensure they do not use the devices as a toy.

CAUTIONS

c.1 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with

wiring, use a qualied electrician.

c.2 - Use only Hunter replacement parts.

MB521-01 • 03/18/15 • © Hunter Fan Company

Page 5

Tools Needed

www.HunterFanInternational.com

Ladder

Pliers Wire Strippers

Power Drill

(optional)

If mounting to a support structure, you will also need these tools.

9/64” Drill Bit

(optional)

MB521-01 • 03/18/15 • © Hunter Fan Company

Screwdrivers

Page 6

CEILING

Mounting Options

www.HunterFanInternational.com

OPTION

If you have a at ceiling:

WALL

Hang your fan by a standard downrod (included).

Standard Mounting

Support Structure

OPTION

If you have an angled ceiling:

1. You will need a longer downrod (sold separately).

2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).

Use the three steps below to determine if your ceiling angle is greater than 34°

Angled Mounting

Standard Mounting Style

Ceiling

Outlet Box

(required)

Angled Mounting Style

Ceiling

Outlet Box

(required)

FOLD

on dotted line

34°

Guide Touches

BOTH Ceiling & Wall

You need ONLY

a Longer

Downrod

*most common

2 3

PLACE

against wall

Guide Touches

but NOT Ceiling

You need BOTH

a Longer

Downrod &

an Angled

Mounting Kit

SLIDE

toward ceiling

Wall

MB521-01 • 03/18/15 • © Hunter Fan Company

Use Standard Mounting

or Low-Prole Mounting

to hang the fan from a at ceiling.

Use Angled Mounting

to hang the fan from a

vaulted or angled ceiling.

Page 7

Ceiling Bracket

Turn Power

OFF

www.HunterFanInternational.com

For angled ceilings, point

opening toward peak.

Make sure all four bumpers are

still attached.

Refer to warning w.1 on pg. 2

Use wood screws (included) when securing to support structure with approved electrical outlet

box. Drill 9/64” pilot holes in support structure to aid in securing ceiling bracket

with hardware found in

the hardware bag.

MB521-01 • 03/18/15 • © Hunter Fan Company

Use machine screws

(provided with outlet

box) when securing to

existing ceiling fan-rated

outlet box. Make sure

it is securely installed

and is acceptable for fan

support of 31.8 kg (70 lbs)

or less.

To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet

box associated with the wall switch location.

Page 8

Motor Housing

www.HunterFanInternational.com

Gently lower the motor housing so it rests

in place on the motor assembly.

Align the screw holes in the top of the motor

housing with the screw holes in the motor

assembly. Install the three motor housing

screws, found in the hardware bag.

MB521-01 • 03/18/15 • © Hunter Fan Company

Page 9

Downrod

www.HunterFanInternational.com

Standard Downrod

for ceilings 2,4-3 m (8-10’) high

Option 1Option 2

Shorter Downrod

for fans installed close to ceiling

Included

(pre-assembled)

Longer Downrod

for angled ceilings or ceilings 3 m (10’)

Option 3

or higher

skip to next page

If you need a different downrod length follow these steps:

Steps 1-5 to remove standard downrod pipe

1 2 3 4 5

Slide

678910

Included

Sold Separately

Steps 6-10 to reassemble with new pipe

MB521-01 • 03/18/15 • © Hunter Fan Company

Page 10

Downrod (continued)

www.HunterFanInternational.com

KEEP!

Remove the pre-installed

setscrew so that the downrod

can be inserted.

Hand tighten the downrod (at

least 4-5 full turns) until it stops.

20 cm

(8”)

MB521-01 • 03/18/15 • © Hunter Fan Company

1 cm

(3/8”)

20 cm

(8”)

(not to scale)

The wires can be cut, but

leave at least 8” extending

from the top of the

Tighten the setscrew

with pliers. DO NOT

HAND TIGHTEN.

downrod.

1 cm

(3/8”)

If the setscrew is not tightened securely, the fan may fall.

Page 11

Downrod (continued)

www.HunterFanInternational.com

Put the wires and downrod through the canopy.

Let the canopy sit loosely on top of the fan.

DO NOT PICK THE FAN UP BY THE CANOPY

OR WIRES. Place the downrod ball into the slot

in the ceiling bracket.

MB521-01 • 03/18/15 • © Hunter Fan Company

Page 12

Wiring

White

(Ungrounded)

Black

Blue

(Grounded)

(Ungrounded)

Using an orange wire

connector from

the hardware bag,

connect the 3 grounding

wires (green, green/

yellow stripe, or bare

copper) coming from the

ceiling, downrod, and

hanging bracket.

Green/Yellow Stripe

(Grounding)

Green/Yellow

Stripe

Note: To connect the wires,

www.HunterFanInternational.com

hold the bare metal leads

together and place a wire

connector over them, then twist

clockwise until tight.

(Grounded)

(Ungrounded)

For Dual Switches

Using the orange wire

connectors from

the hardware bag,

For a Single Switch

Using the orange wire

White

Blue

Black

connectors from the

hardware bag, connect the

black wire (ungrounded)

from the ceiling to the black

and the blue wires from the fan. Connect the white wire

(grounded) from the ceiling to

the white wire from the fan.

connect the white wire

(grounded) from the

ceiling to the white wire

from the fan. Connect the black wire (ungrounded) from the

ceiling to the black wire

from the fan. Connect the

second (ungrounded) wire

from the ceiling to the blue

wire from the fan.

Refer to CAUTION c.1 on pg. 2

Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of

the outlet box and the ungrounded wires on the other side of the outlet box.

MB521-01 • 03/18/15 • © Hunter Fan Company

Page 13

Canopy

www.HunterFanInternational.com

Screw

Holes

Position the canopy so that, when

lifted into place, the canopy ts into

the hanging bracket as shown.

Lift the canopy into place so that

the screw holes are aligned.

MB521-01 • 03/18/15 • © Hunter Fan Company

Insert the two canopy screws

found in the hardware bag.

Note: Fan style may vary.

Page 14

Blades

www.HunterFanInternational.com

Place each blade between a blade iron

and medallion. Install three blade screws,

found in the hardware bag, to attach the

medallion to the blade iron.

Lightly attach the blade irons to the motor

with screws found in the hardware bag, then

securely tighten after both screws are attached.

MB521-01 • 03/18/15 • © Hunter Fan Company

Page 15

Switch Housing & Light Kit

Red Flag

www.HunterFanInternational.com

Remove the pre-installed light kit

assembly screw and red ag from the

light kit assembly. Save the screw. It will

be needed for light kit installation.

Note: The screw was installed for

shipping purposes only.

Remove and discard the plastic connectors

from the ends of the two pull chains.

Carefully remove the light kit from the upper

switch housing and set the light kit aside.

Page 16

Switch Housing & Light Kit (continued)

Switch Housing

Assembly Screw

www.HunterFanInternational.com

Partially install two switch housing assembly

screws ,found in the hardware bag, into

the motor housing as shown. It does not

matter which two screw holes you choose.

Feed the wire plug through the center hole

of the upper switch housing, then wrap

keyhole slots around the two screws and twist

counterclockwise to lock the upper switch

housing into place.

Insert the third screw, found in the

hardware bag, into place and then tighten

all three screws.

Make sure the upper switch housing is securely attached

to the mounting plate. Failure to properly secure all 3 assembly

screws could result in the switch housing xture falling.

Page 17

Switch Housing & Light Kit (continued)

Empty

Post

www.HunterFanInternational.com

Light Kit

Assembly

Screw

Partially install three light kit assembly

screws, found in the hardware bag,

into the posts as shown, leaving the

circled post empty.

Use only the light kit supplied

with this fan model.

Connect the plugs from the upper and lower

switch housings. Make sure to line up the

colored markings on the connectors.

Keyhole

Slot

Align the three keyhole slots in the light kit

with the three assembly screws in the posts.

Lift the light kit and twist clockwise to lock it

into place. Be sure that both pull chains are

hanging freely.

Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all

three assembly screws could result in the light xture falling.

Page 18

Switch Housing & Light Kit (continued)

Remember the screw you

kept after removing the

red ag (page 13)? You

need it for this step.

www.HunterFanInternational.com

Install the fourth light kit assembly screw

and tighten all four screws securely.

Install a bulb into each of the sockets.

When necessary, replace with bulbs of

the same wattage.

Page 19

Globe

www.HunterFanInternational.com

Globe

Assembly

Screws

Feed the pull chains from the fan switch and

the light switch down through the holes in the upper switch housing as shown. Attach the pull chain pendants to the light and fan

pull chains. The fan pull chain controls the

speed: from high to off. The light pull chain

controls the light xture: on and off.

Partially install two globe assembly screws, found in the hardware bag, halfway into

the light kit assembly as shown. It does not

matter which two screw holes you choose.

Carefully lower the globe into the globe

retainer until it rests in place.

Page 20

Globe (continued)

www.HunterFanInternational.com

CONGRATULATIONS!

YOU’RE DONE!

Align the keyhole slots in the globe assembly

with the partially installed screws in the light

kit assembly. Lift the globe assembly and

twist counterclockwise to lock it into place.

Make sure the globe assembly is securely attached to the switch housing. Failure to properly secure all three assembly

screws could result in the light xture falling.

Install the third globe assembly screw

and tighten all three screws securely.

Page 21

Maintenance & Cleaning

Turn Power

www.HunterFanInternational.com

Reverse

Switch

Changing the bulbs - carefully

remove the globe assembly.

Unscrew the bulbs and replace

with bulbs of the same wattage.

Reinstall the globe assembly.

Changing the direction of air

ow - move the reverse switch

to the opposite position.

Note: The reversing switch is

located on the switch housing.

It can only be accessed when

globe is removed.

Cleaning the fan - use soft

brushes or cloths to prevent

scratching. Cleaning products

may damage the nishes.

Page 22

Troubleshooting

www.HunterFanInternational.com

Fan doesn’t work

• Make sure power switch is on.

• Pull the pull chain to make sure it is on.

• Push the motor reversing switch

rmly left or right to ensure that

it is engaged.

• Check the circuit breaker to ensure the power is turned on.

• Make sure the blades spin freely.

• Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram on page 10.

• Check the plug connection in the switch housing.

Excessive wobbling

• Tighten all of the blade and blade iron screws until they are snug.

• Turn the power off, support the fan carefully, and check that the hanger ball is properly seated.

• Use the provided balancing kit and instructions to balance the fan.

Noisy Operation

• Tighten the blade and blade iron screws until they are snug.

• Check to see if any of the blades are cracked. If so, replace all of the blades.

Lights dim when turned on or do not turn on at all.

• Make sure the wattage of the light bulbs installed matches

the specications on the light

sockets.