Hunter Fan HTF2386 Installation and Assembly

30 inches
7 feet
Ladder
Table of Contents
www.HunterFan.com
1.888.830.1326
Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance
in your home or ofce for many
years. This installation and operation manual contains complete instructions for installing and operating your fan.
We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world.
To register your fan please visit: www.HunterFan.com/register
What to Expect with
Your Installation
2
Hanging the Fan
6
Switch Housing
Tools Needed
PAG E
PAG E
Wiring
Ceiling Bracket
PAG E
3
Motor Housing
PAG E
7
Maintenance,
Operation & Cleaning
4
8
Preparation
PAG E
PAG E
5
Blades
PAG E
PAG E
9
TroubleshootingLight Kit
?
?
PAG E
10
PAG E
11
1
M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company
13
PAG E
?
PAG E
14
What to Expect with Your Installation
www.HunterFan.com
1.888.830.1326
Must be able to secure the fan to building structure or fan-rated outlet box
You may need a friend to help you.
Check box to see fan weight
If you are unfamiliar with wiring, use a
qualied electrician.
Know your wiring
30 inches
from blade tip to nearest wall or obstruction
Assess location
7 feet
from bottom
edge of blade
to the oor
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
w.1 - To reduce the risk of re, electrical shock, or
personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
w.3 - To reduce the risk of re, electrical shock, or motor damage, use only Hunter Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade brackets when installing the blade brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
CAUTIONS
c.1 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar
with wiring, use a qualied electrician.
c.2 - Use only Hunter replacement parts.
2
M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company
Tools Needed
www.HunterFan.com
1.888.830.1326
Escalera
Taladro eléctrico
(opcional)
Si se monta a una estructura de soporte, también necesitará estas herramientas.
Destornilladores
Broca de 9/64”
(opcional)
M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company
No deseche las bolsas con herrajes ni
mezcle las partes de diferentes bolsas. Tome nota del símbolo impreso en cada bolsa con herrajes. Los símbolos pueden
ser usados para identicar los herrajes
apropiados para cada paso.
3
Ceiling Bracket
Turn Power
Bumper
www.HunterFan.com
1.888.830.1326
OFF
To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to the
outlet box associated with the wall switch location.
Make sure all four bumpers are still attached.
4
M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company
Use wood screws (included) when securing to support structure with approved electrical outlet
box. Drill 9/64” pilot holes in support structure to aid in securing ceiling bracket
with hardware found in
the hardware bag.
Use machine screws
(provided with outlet
box) when securing to
existing ceiling fan-rated
outlet box. Make sure
it is securely installed
and is acceptable for fan
support of 31.8 kg (70 lbs)
or less.
Refer to warning w.1 on pg. 2
Ceiling Bracket (continued)
Preparation
www.HunterFan.com
Time Saver Tip: Get a helper
to insert grommets, found in
the hardware bag, into the
blades while you’re doing the
next couple of steps.
1.888.830.1326
5
M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company
Hanging the Fan
Ground
Wire
Screw Hole
Locking
Screw
Screw
Hole
www.HunterFan.com
1.888.830.1326
While holding the wires out of the way, lift
the motor assembly and place the square
hanger into the opening in the ceiling
bracket. Be sure the ground wire attached
to the hanger faces out of the large
opening in the ceiling bracket.
Once the motor is in the ceiling bracket, use the two locking screws, found in the
hardware bag, to secure the motor to
the ceiling bracket. Then partially install
two of the canopy screws, found in the hardware bag, in the screw holes on opposite ends of the hanger bracket.
Note: Fan style may vary.
6
M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company
Wiring
F
R
O
M
F
A
N
White
(Ungrounded)
Black
Blue
(Grounded)
F
R
O
M
C
E
I
L
I
N
G
(Ungrounded)
Using an orange wire
connector from
the hardware bag,
connect the 3 grounding
wires (green, green/
yellow stripe, or bare
copper) coming from the
ceiling, downrod, and
hanging bracket.
O
R
F
F
A
M
N
O
R
F
Green/Yellow Stripe
F
R
O
M
C
M
(Grounding)
Green/Yellow
Stripe
E
I
L
Note: To connect the wires,
www.HunterFan.com
E
C
I
L
I
N
G
hold the bare metal leads
together and place a wire
connector over them, then twist
E
C
I
L
I
M
N
O
R
F
G
1.888.830.1326
clockwise until tight.
(Grounded)
(Ungrounded)
For Dual Switches
Using orange wire
connectors from
the hardware bag,
For a Single Switch
Using the orange wire
White
Blue
Black
connectors from
the hardware bag, connect
the black wire (ungrounded)
from the ceiling to the black
and the blue wires from the fan. Connect the white wire
(grounded) from the ceiling to
T
E
K
C
A
R
B
I
G
N
the white wire from the fan.
F
R
O
N
A
F
M
connect the white wire
(grounded) from the
ceiling to the white wire
from the fan. Connect the black wire (ungrounded) from the
ceiling to the black wire
from the fan. Connect the
second (ungrounded) wire
from the ceiling to the blue
wire from the fan.
Refer to CAUTION c.1 on pg. 2
Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
7
M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company
Motor Housing
Keyhole
Canopy
Screw
Keyhole
Rubber
Plug
Canopy
Screw
www.HunterFan.com
1.888.830.1326
Place the fan housing over the motor. Align
the keyholes in the fan housing with the
two partially installed canopy screws in the
hanger bracket. Rotate the fan housing to
situate the screws in the end of the keyholes.
The motor housing is not secured until the next step is complete. Do not leave
unattended.
Install the two remaining canopy screws,
found in the hardware bag, into the
holes in the fan housing and into the
hanger bracket. Securely tighten all screws.
Tighten all four screws securely. Install the
rubber plugs, found in the hardware
bag, into the holes over the canopy screws.
8
M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company
Blades
Insert grommets found in the hardware
Lightly attach the blade irons to the
www.HunterFan.com
1.888.830.1326
bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag.
motor with screws found in
the hardware bag, then securely
tighten after both screws are attached.
9
9
M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company
Switch Housing
www.HunterFan.com
1.888.830.1326
Screw two housing assembly screws
from the hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
10
M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company
Insert the third screw, found in
the hardware bag, into place and
then tighten all three screws.
Make sure the upper switch housing is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch
housing xture falling.
Light Kit
Switch Housing Screw
Switch Housing Screw
Notch
www.HunterFan.com
1.888.830.1326
Partially install two of the switch housing
screws found in the bag. Connect
the plugs from the upper and lower
switch housings. Make sure to line up the
colored markings on the connectors.
Want to install your fan without a light kit?
Go to www.HunterFan.com/FAQs and click
“How do I install my fan without the light kit?”
Align the notches in the sides of the lower
switch housing with the upper switch
housing screws. Lift the lower switch housing.
Twist the lower switch housing clockwise
to lock into place. Then thread the fan
pull chain through the hole in the light kit.
M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company
Install the third switch housing screw.
Tighten all three screws securely.
Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all three
assembly screws could result in the light xture falling.
Light Kit (continued)
Metal Plate
Globe
Globe Keeper
Finial Cap
Finial
Light Pull Chain
Fan Pull
Chain
www.HunterFan.com
CONGRATULATIONS!
YOU’RE DONE!
1.888.830.1326
Install a light bulb in each socket.
Note: Globe style and number of
lights may vary.
Press the globe and globe keeper
ush against the metal plate. Thread
the light pull chain through the hole
in the center of the nial cap and
thread the fan pull chain through the
hole in the side of the cap. Finally,
thread only the light pull chain
through the hole in the nial and
screw the nial onto the threaded rod.
M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company
Connect the appropriate pull chain pendant to each of the
short chains coming from the
nial and nial cap. The fan pull
chain controls the speed: high, medium, low, and off. The light
pull chain controls the light
xture: on and off.
12
See next page for fan operation instructions.
Note: In compliance with US federal energy regulations, this ceiling fan
contains a device that restricts its light output. Exceeding the wattage
limit marked on the MAX wattage sticker afxed to the light socket(s)
may result in re hazard or improper operation.
Maintenance, Operation & Cleaning
Turn Power
ON
Metal Plate
Globe
Globe Keeper
www.HunterFan.com
1.888.830.1326
Finial Cap
Finial
Changing the bulbs - unscrew
the nial and remove it from the
threaded rod. Remove the nial cap
and unscrew the globe keeper while
supporting the globe with your other
hand. Carefully remove the globe.
Unscrew bulbs and replace with bulbs of same type and wattage.
Reinstall the globe assembly.
M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company
Reverse
Switch
Changing the direction of air
ow - move the reverse switch
to the opposite position.
13
Cleaning the fan - use soft
brushes or cloths to prevent
scratching. Cleaning products
may damage the nishes.
For questions regarding removing a light kit, call
customer service 1-888-830-1326.
Troubleshooting
www.HunterFan.com
1.888.830.1326
Fan doesn’t work
• Make sure power switch is on.
• Pull the pull chain to make sure it is on.
• Push the motor reversing switch
rmly left or right to ensure that
it is engaged.
• Check the circuit breaker to ensure the power is turned on.
• Make sure the blades spin freely.
• Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram on page 7.
• Check the plug connection in the switch housing.
Excessive wobbling
• Tighten all of the blade and blade iron screws until they are snug.
• Use the provided balancing kit and instructions to balance the fan.
Noisy Operation
• Tighten the blade and blade iron screws until they are snug.
• Check to see if any of the blades are cracked. If so, replace all of the blades.
14
M3504-01 • 02/08/17 • © 2012–2017 Hunter Fan Company
Loading...