Page 1
Installation Instructions
For Hunter Ceiling Fan Light Kits
Preparing for Installation
Aurora Style
CAUTIONS
· Read entire text carefully before
beginning installation and save these
instructions.
· To reduce the risk of electrical shock,
install this light kit only on listed Hunter
ceiling fans type A through Z.
WARNINGS
· To avoid possible electrical shock, before
installing light fixtures, disconnect power
by turning off the circuit breakers both
to the outlet box and to its associated wall
switch location. If you cannot lock the
circuit breakers in theoff position,
securely fasten a prominent warning
device, such as a tag, to the service panel.
· Connect house wiring to the fan before
attaching the light fixture to the fan.
· All wiring must be in accordance with
national and local electrical codes. If you
are unfamiliar with wiring, you should use
a qualified electrician. Professional
installation is recommended.
1. Unassemble the fan switch housing as shown in
Figure 1.
2. Disconnect the upper and lower plug connectors
between the upper switch housing and lower
switch housing.
Note: Do not discard any parts. You will need to
replace it if you remove the light fixture in the
future.
Switch
Housing
Cover
Plate
Upper Switch
Housing
Switch
Housing
Assembly
Screws
Lower
Switch
Housing
Plug Button
Switch Housing
Assembly Screws
Figure 1 - Unassembling the fan switch housing
© 2003 Hunter Fan Company 1 41558-01 3-6-2003
Page 2
Installing the Light Fixture
1. Insert the black wire and white wire from the
light kit assembly through the hole in the bottom
of the lower switch housing. Refer to Figures 2
and 3.
2. Securely tighten the light kit assembly into the
bottom of the lower switch housing. Refer to
Figure 3.
3. Install the nut and washer onto the end of the
light kit assembly inside of the lower switch
housing. Securely tighten the nut and washer.
Insert and tighten the two #6-32 sems light
fixture mounting screws. Refer to Figure 3.
4. Using the wire nuts on the two light kit wires in
the lower switch housing, connect the black wire
from the light kit assembly to the black/white
wire from the lower switch housing and connect
the white wire from the light kit assembly to the
white wire from the lower switch housing.
5. Reconnect the upper plug connector from the
upper switch housing to the lower plug connector
in the lower switch housing. Refer to Figure 4.
Note: Both plug connectors are polarized and will
only fit together one way. Make sure that both
connectors are properly aligned before connecting
them together. Incorrect connection could cause
improper operation and damage to the product.
6. Align the holes in the upper switch housing and
the lower switch housing. Securely tighten the
three switch housing screws assembly screws.
Refer to Figure 1 and 4.
Lower
Switch
Housing
Light Kit
Assembly
Figure 2 - Assembling
the Light Kit
Upper Plug
Connector
Figure 3 - Attached Light
Kit Assembly
Upper
Switch
Housing
Lower Plug
Connector
Figure 4 - Connecting the Plug Connectors
41558-01 3-6-2003 2 © 2003 Hunter Fan Company
Page 3
Installing Globes and Bulbs
Thread the fan switch pull chain through the
grommetted hole in the light fixture bracket. Unfasten
the extra chain looped through the hole in the in the
lower mounting cap and attach it to the fan switch
pull chain. Repeat for light switch pull chain.
Refer to Figures 5, 6 and 7.
1. Install bulbs. Use 60W Max, A-15 bulbs.
2. Thread the fan switch pull chain through the hole in
the metal disk.
3. Place globe on pipe until flush against metal disk.
4. Thread the light switch pull chain through the large
center opening of the globe.
5. Thread the fan switch pull chain through the small
center opening in the globe.
6. Place the cover plate up against the underside of
the globe. Pass light and fan switch pull chains
through the appropriate holes.
7. Thread the light switch pull chain through the
finial and screw the cap onto the pipe end until
tight.
Hole in Lower
Mounting Cap
Figure 6 - Attaching Fan Switch Pull Chain Extension
Fan Switch
Pull Chain
Bulb
Socket
Grommetted
Hole
Lower Mounting Cap
Extra Chains
Figure 5 - Threading Fan Switch Pull Chain through
Grommet
Globe
Figure 7 - Aurora Fixtures
Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38125
United States of America
Pipe
Metal Disk
Light
Switch Pull
Chain
Cover Plate
Finial
© 2003 Hunter Fan Company 3 41558-01 3-6-2003
Loading...