shock, DO NOT use this fan with any
solid-state speed control device.
CAUTION
When using electrical appliances,
basic precautions should
always be taken to reduce the
risk of re, electric shock and
personal injury:
1. Read all instructions before
using this fan.
2. Improper installation may result
in the risk of re, electric shock
or personal injury.
3. To prevent the risk of re and
electric shock, DO NOT use
the unit near windows. Rain
and moisture may create an
electrical hazard.
4. The power plug must be
removed from the power
socket when not in use,
before cleaning, servicing,
maintenance and before
moving to another location.
5. DO NOT put fan in a damp
place or where humidity is highsuch
as a bathroom.
6. The fan should be placed on a
at, stable surface or tabletop
to avoid overturning.
7. Use fan only for intended use,
as described in this instruction
manual.
8. To protect against electrical
shock, DO NOT immerse unit,
plug or cord in water or spray
with liquids.
9. Close supervision is necessary
when any appliance is used by
or near children.
10. NEVER insert ngers, pencils
or any other objects through the
grill when the fan is running.
11. DO NOT operate any appliance
with a damaged cord or plug,
after the appliance malfunctions
or has been dropped or
damaged in any manner.
12. To disconnect, grip plug and
pull from wall outlet. NEVER
yank on cord.
13. ALWAYS use on a dry surface.
14. This product is intended for
household use only and not for
commercial or industrial use.
15. DO NOT operate fan in the
presence of explosive and/or
ammable fumes.
16. DO NOT place fan or any parts
near an open ame, cooking or
any other heating appliances.
17. DO NOT use near curtains,
plants, window treatments, etc.
18. This appliance has a grounded
three-prong plug and is suitable
for grounded receptacle use
only. An adapter is available
for connecting three-blade
grounding-type plugs to two-slot
receptacles. The adapter must
be properly grounded. DO NOT
attempt to defeat the purpose
of this safely feature.
2
Page 3
WELCOMEUNPACKING
Thank you for choosing Hunter’s
12-Inch High-Performance Table
Fan. This manual gives you complete instructions for using your fan.
Here are some the features you will
enjoy with your fan:
• An attractive design that enhances any decor
• A powerful Hunter motor for maximum air ow
• Three speeds to adjust your
comfort level
Before installing your fan, record
the following information for your
records and for warranty assistance.
Model Name _________________
Date Code ___________________
Date Purchased _______________
Where Purchased _____________
As you unpack the fan, save the
carton and packing materials in
case you want to move or ship the
unit in the future.
Carefully remove all items from the
box.
NOTE: It is best to have someone
hold the box while you lift the fan
and the protective packaging out of
the carton.
Make sure all shipping materials
are removed from fan before operating.
Please attach your receipt
or a copy of your receipt
to this manual for future
reference.
3
Page 4
GROUNDING INSTRUCTIONS
Grounded
Plug
Grounding Pin
Grounded Outlet
Box Cover
Adapter
Grounding
Means
Metal
Screw
Grounded Outlet
Cover Box
This appliance is for household use
only and may be plugged into any
120-volt AC electrical outlet (ordinary household current). DO NOT
use any other type of outlet.
WARNING
This unit is suitable for grounded
receptacle use only.
The cord has a grounded plug as
shown in Figure 1. An adapter, as
shown in Figure 2, is available for
connecting three-blade groundingtype plugs to two-slot receptacles.
The green grounding lug extending
from the adapter must be connected to a permanent ground such
as a property grounded outlet box.
The adapter should not be used if
a three-slot grounded receptacle is
available.
LINE CORD SAFETY TIPS
1. NEVER pull or yank on the cord
or the appliance.
2. To insert plug, grasp it rmly
and guide it into the outlet.
3. To disconnect the appliance,
grasp the plug and remove it
from the outlet.
4. Before each use, inspect the
line cord for cuts and/or abrasion marks. If any are found,
the appliance should be
serviced and the line cord replaced. Please return it to our
Service Department or to an
authorized service representative.
5. NEVER wrap the cord tightly
around the appliance, as this
could place undue stress on the
cord where it enters the appliance and could cause it to fray
and break.
6. DO NOT operate appliance if
the line cord shows any damage, if the appliance works
intermittently or stops working
entirely.
FIGURE 2FIGURE 1
4
Page 5
OPERATION
Handle
Oscillation
Pin
Power / Speed
Control Switch
This appliance is for household use
only.
1. Place the fan on a dry, safe, at
surface where it cannot fall or
be pulled by the cord.
2. Plug the fan into a grounded
120-volt AC electrical outlet (ordinary household current).
DO NOT use any other type
of outlet. Make sure that the
rated voltage of the fan is the
same as the power source before plugging it into the power
source.
3. Turn the fan “ON” or “OFF” by
sliding the Power/Speed Control to the up or down. The
power should always be OFF
before unplugging the fan.
4. To select the speed, move the
Power/Speed Control up from
OFF (O) to the desired speed
setting: Low, Medium. or High.
5. To make the fan oscillate, push
the oscillation pin down. To stop
oscillating, pull the oscillation
pin up.
HERITAGE mODEL
FIGURE 3
5
Page 6
MAINTENANCE
Grille Ring
Screw
Grille
Ring
This fan is permanently lubricated
and will not require additional lubrication (oil) for the life of the fan.
This fan requires little maintenance
and contains no user serviceable
parts. DO NOT try to x it yourself.
Contact qualied service personnel
if servicing is needed.
TO CLEAN:
1. Before cleaning, turn fan off and
unplug from electrical outlet.
Wipe off excess dust with a lintfree cloth.
2. To ensure adequate air circulation
to the motor, keep vents located
at the rear of the motor housing free from dust accumulation.
A vacuum cleaner hose can be
used to clean these vents.
3. DO NOT immerse the fan in water or any other liquid.
CLEANING GRILLE AND BLADE:
1. Turn the fan off and unplug from
the electrical outlet.
2. Disassemble Grilles by carefully
removing the Grille Ring Screw
on the bottom of the grille and
removing the Grille Ring. See
Figure 4.
FIGURE 4
3. Grilles and blades may be cleaned
with soft cloth dampened with
mild soap and water.
4. Use a soft, slightly damp cloth to
wipe the remaining fan parts.
5. DO NOT allow water or any other
liquid to get into the motor housing or base.
6. After the Blades and Grilles have
dried completely, reassemble the
fan. Reposition the Grille Ring so
that the Grille Ring Screw is at
the bottom of the Grilles. Carefully align the Grille Ring Screw into
its holes and tighten it so that the
Grille Ring is securely in place.
DO NOT OVERLY TIGHTEN.
7. DO NOT plug fan into an electrical outlet until it has been fully
reassembled.
6
Page 7
STORAGETROUBLESHOOTING
1. Keep the original packaging for
the purpose of storing the fan.
2. ALWAYS store the fan in a dry
place.
3. NEVER store the fan while it is
still plugged in.
4. NEVER wrap the cord tightly
around the fan.
5. DO NOT put any stress on the
cord where it enters the fan, as
it could cause the cord to break.
PROBLEM
• Can not turn on fan.
SOLUTION
• Make certain the fan is plugged
in and that the power outlet has
power.
PROBLEM
• Fan will not oscillate.
SOLUTION
• Push down on the Oscillation
Pin.
If you have tried these troubleshooting solutions and still have
trouble, call 1-888-830-1326 (For
CAN: 1-866-268-1936) or visit our
Web site at
http://www.hunterfan.com.
HUNTER FAN COMPANY
2500 FRISCO AVENUE
MEMPHIS, TN 38114
7
Page 8
8
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.