Hunter Fan 42935-0, 8203, 82030, 82032 User Manual

I n s t a l l a t i o n G u i d e

See page 2

ENGLISH

Vea la página 19

ESPAÑOL

Energy Star Bath Fan Models 82030, 82031, & 82032

READ and SAVE THESE INSTRUCTIONS

1

42935-01 06/04/2007

3 ft. min.
(0.91 m)

Bath Fan

Tub or Shower area

NOTE: This illustration is not
to scale

7 ft. min.
(2.13 m)

W A R N I N G

TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, OBSERVE THE FOLLOWING:

1) Read all instructions before attempting to install or use this appliance. This appliance is for general
ventilating use only. Do not use this appliance for ventilating hazardous or explosive materials. Follow
the heating equipment manufacturer’s guideline and safety standards, such as those published by
the National Fire Prevention Association (NFPA), and the American Society for Heating, Refrigeration
and Air-Conditioning Engineers (ASHRAE), and the local code authorities.
described in this manual. Any other use not recommended by the manufacturer may cause
fire, electric shock, or injury to persons. SAVE THESE INSTRUCTIONS.

2)

Before installing, servicing, or cleaning the unit, disconnect the power by turning o the circuit
breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers
in the o position, securely attach a prominent warning device, such as a tag, to the service panel.

3)

This unit must be grounded.

4)

This appliance is not suitable for tub or shower installation, and must not be installed within a
minimum of 3 feet from the tub or shower opening. See Figure A.

5)

Do not install this appliance lower than 7 feet (2.13 m) above the floor in the ceiling. See Figure A.

Use this appliance only as

42935-01 06/04/2007

Figure A

Continued

2

6)

Never place a switch where it can be reached from a tub or shower. Do not install this appliance in
a tub or shower enclosure.

7)

Installation work and electrical wiring must be done by qualified person(s) in accordance with all
applicable codes and standards, including fire-rated construction codes and standards.

8)

When cutting or drilling into wall(s) or ceiling, do not damage electrical wiring or other hidden
utilities.

9) Do not install this product in a wall. This product is designed for installation in ceilings up
to a 12/12 pitch (45 degrees). Ductwork must point upward.

10)

Ducted fans must always be vented to the outdoors. Keep ducting as short and as straight as pos-

sible.

11) Extreme caution is necessary when any is used by or near children or invalids and when­ever the is left operating and unattended.

12) To avoid motor bearing damage and noisy/unbalanced blower wheel, keep drywall spray,
construction dust, etc. off power unit.

13) Read specification label on product for further information and requirements.

14) Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this
may cause an electric shock or fire, or damage the unit.

15)

Do not use this appliance with a dimmer switch or a fan speed controller.

16) To reduce the risk of fire or electrical shock, do not use this fan with any solid-state speed control
device.

17) To prevent a possible fire, do not block air intakes or exhaust in any manner.

18) If this unit is to be installed over a tub or shower, it must be marked as appropriate for the
application and be connected to a GFCI (Ground Fault Circuit Interrupter)-protected branch
circuit.

3

42935-01 06/04/2007

F

G

H

I

L

M

x2

N

x3

*

*

A

B

C

95044-01-000

97128-01-000

03242-07-133

97118-01-000

x2

D

97517-01-000

74508-03-133

Mounting Rails

Housing

Wiring Cover

Fan Assembly

3/8” Cable Connector

Bezel

Wiring Cover Screw

Check all the parts. If damaged, call

1-888-830-1326 for replacement.

x4

E

Mounting Screws

Fan Mounting Screws

*

NOTE:

Strain relief (not supplied) cable
connector must be installed.

Attachment Screws

97934-01-262

97118-03-000

97118-05-000

J

Strain Relief Bracket

K

Strain Relief Bracket Screw

65827-01-000

74508-53

A

B

Before Installation

Estimated assembly time: 30 to 60 minutes

Included.

Tools Needed. (Not supplied.)

Turn off the power source.

42935-01 06/04/2007

Loosen the fan mounting screws.

4

Remove the fan assembly from the housing.

D

E

C

Remove the wiring cover.

Loosen the wiring cover screw.

Choose Installation Option

For New Construction - attaching to joist, go to step A1, page 5.

For New Construction - suspended between, joists go to step B1, page 7.

For Existing Construction - accessible from above, go to step C1, page 9.

For Existing Construction - accessible only from below, go to step D1, page 12.

5

42935-01 06/04/2007

A1

Section A - New Construction - attaching to joist

5/8
1/2

5/8
1/2

A2

A5

A3

3”

A4

OR

Pop out a wiring access slug.

the joist based upon the the thickness of your sheetrock.

Run the power supply wire through the strain relief, leav-

ing 3” between the end of the wire and the strain relief.

42935-01 06/04/2007

Tighten the strain relief around the wire.

Drive mounting screws (supplied) into joist or framing.Position the correct depth mark at the bottom edge of

Install the wiring and the strain relief into the wiring

access hole you made earlier.

6