Hunter Fan 82022 User Manual [en, es, fr]

La Strada

Bath Ventilator with Light

English

Español

Página 22

Owner’s Manual

Model

82022

Français

Page 43

42929-01
20101026
©2010 Hunter Fan Co.

42929-01 10/26/2010

W A R N I N G

TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, OBSERVE THE FOLLOWING:

1. Use this unit only in a manner intended by the manu­facturer. If you have questions, contact the manufac­turer at the phone number or address listed in the
warranty.

2. Before installing, servicing, or cleaning the unit,
disconnect the power by turning o the circuit break­ers to the outlet box and associated wall switch loca­tion. If you cannot lock the circuit breakers in the o
position, securely attach a prominent warning device,
such as a tag, to the service panel.

3. Installation work and electrical wiring must be done
by qualified person(s) in accordance with all applicable
codes and standards, including fire-rated construction
codes and standards.

4. When cutting or drilling into wall(s) or ceiling, do not
damage electrical wiring or other hidden utilities.

5. Ducted fans must always be vented to the outdoors.
Keep ducting as short and as straight as possible.

6. Acceptable for use over a bathtub or shower when
connected to a GFCI protected branch circuit.

7. Install fan at least 5 feet (1.52 m) above the floor.

8. Never place a switch where it can be reached from a
tub or shower.

9. This unit must be grounded.

C A U T I O N

1. For general ventilating use only. Do not use for
ventilating hazardous or explosive materials.

2. To avoid motor bearing damage and noisy/unbal­anced impellers, keep drywall spray, construction
dust, etc. off power unit.

3. DO NOT install this product in a wall. This prod­uct is designed for installation in ceilings up to a
12/12 pitch (45 degrees). Ductwork must point
upward.

4. Please read specification label on product for fur­ther information and requirements.

W A R N I N G

DISCONNECT

ELECTRIC
POWER SUPPLY
AND LOCK OUT

SERVICE PANEL

BEFORE

SERVICING UNIT

PREVENTATIVE MAINTENANCE

A clean fan provides better service. Disconnect the power supply and clean the fan as listed below.

TO CLEAN GRILLE:
Use a mild detergent, such as dishwashing liquid, and a soft cloth. DO NOT use abrasive cloths, steel wool pads
or scouring powders.

TO CLEAN FAN ASSEMBLY: Unplug motor cord from receptacle. To remove motor plate, find the single tab on the
motor plate (located next to the receptacle). Push up rear motor plate tab while pushing out on the side of the
housing or insert a screwdriver into the slot in the housing (next to tab) and twist screwdriver. Gently vacuum
fan, motor and interior of housing.

METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WATER.

MAINTENANCE

The motor is permanently lubricated and never needs oiling. If the motor bearings are making excessive or
unusual noises, replace the motor with the exact service motor. You should replace the impeller at the same
time.

2

42929-01 10/26/2010

Check all the parts.

If damaged, call
1-888-830-1326

for replacements.

x4

A

B

*

3/8” Cable Connector

95044-01-096

E

95029-01-000

F

77481-01-000

G

03242-01-232

H

95491-06-000

I

74508-03-133

J

77521-01-000

K

C

*

x2

*

D

NOTE:

Strain relief cable connector
must be installed. Not
Included.

Extra Screws

Before Installation

65219-01-000

L

97258-01-000

M

75184-01-092

N

97260-01-000

O

76079-02-481

P

Tools Needed. (Not supplied.)

Estimated assembly time: 30 to 60 minutes

NOTE: Remove all packing materials before installation.

1

42929-01 10/26/2010

Turn off the power source.

2

J

F

Loosen screws.

3

5

3

6

42929-01 10/26/2010

4

I

F

Remove the motor/blower from the housing.

Remove the pre-loaded screw tip covers.

Remove packing material.

Back out the pre-loaded screw tips until flush

with the side of the housing.

7

8

G

H

Remove the wiring cover screw.

4

Remove the wiring cover.

42929-01 10/26/2010

9

10

F

C

B

Pop out the first wiring access slug. Use second if needed. Insert the strain relief (not included) into the housing and

secure with washer.

Choose Installation Option

For New Construction - attaching to joist go to step A11, page 5

For New Construction - suspended between joists go to step B11, page 8

For Existing Construction - accessible from above go to step C11, page 11

For Existing Construction - accessible only from below go to step D11, page15

New Construction - attaching to joist

A11

Position the correct depth mark at the bottom edge of the

joist based on the thickness of your sheetrock.

42929-01 10/26/2010

5/8
1/2

A12

F

5/8
1/2

Screw pre-loaded screws into joist or framing.

5

A13

42929-01 10/26/2010

Route wires through the strain relief.

A14

A15

Black

2 Pin

White

Fan Motor

White

3 Pin

Light

*Option Fan & Main Light Together

Black

*Option

Light

Connect wires as shown.

A16

0

Ground

Green

A

Bare Copper

Black

Main Switch 1 (AC In)

White

Black

Switch 2 (AC In)

F

H

Install the wiring cover plate. Make sure all

wiring connections are inside the box or under

the wiring cover plate.

6

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may need

to be purchased.

42929-01 10/26/2010

0000

A17

A18

0000

I

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

A19

J

Secure the motor by tightening the 2 screws.

Reinstall the motor by inserting the tabs and pushing up

into position. Make sure the wires are not pinched

between the motor and the housing.

A20

Turn on the power source.

A21

Test the motor. If the motor does not run, check the plug

42929-01 10/26/2010

ON

connection.

OFF

A22

Go to step

E1

on page 17

to attach grille.

7

New Construction – suspended between joists

5/8
1/2

42929-01 10/26/2010

B11

B13

F

Slide the mounting rails into brackets.

B12

E

5/8
1/2

Position the correct depth mark at the bottom edge of

the joist based on the thickness of your sheetrock.

B14

F

Mark position of screws by using holes as a template.

B15

1/8” bit

Drill a hole in the center of each outline.

B16

8

Insert screws, leaving space between the screw

head and the joist. Screws are not provided.

Attach the rails onto the screws.

42929-01 10/26/2010

B17

B18

Tighten screws. Route wires through the strain relief.

B19

B20

Black

2 Pin

White

Fan Motor

White

3 Pin

Light

*Option Fan & Main Light Together

Black

*Option

Light

Connect wires as shown.

B21

Ground

Green

A

Bare Copper

Black

Main Switch 1 (AC In)

White

Black

Switch 2 (AC In)

H

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under the

42929-01 10/26/2010

wiring cover plate.

G

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may need

to be purchased.

9

B22

42929-01 10/26/2010

B23

I

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

B24

J

I

Reinstall the motor by inserting the tabs and pushing up

into position. Make sure the wires are not pinched

between the motor and the housing.

B25

10

Secure the motor by tightening the 2 screws.

B26

ON

Test the motor. If the motor does not run,

check the plug connection.

OFF

Turn on the power source.

B27

Go to step

E1

on page 17

to attach grille.

42929-01 10/26/2010

Existing Construction – accessible from above

5/8
1/2

C11

Remove an existing fan and check to make sure the

opening is large enough to accommodate the new

EXISTING FAN

motor housing (8”x 8 1/2”).

NO EXISTING FAN

OR

Use the motor housing as a template to mark position.

C12

F

C13

8”

Cut out an opening for the housing.

8 1/2”

5/8
1/2

E

Slide the mounting rails into brackets.

C14

Position the correct depth mark at the bottom edge of the

joist based on the thickness of your sheetrock.

42929-01 10/26/2010

Mark position of screws by using holes as a template.

11

C15 C16

42929-01 10/26/2010

C17

Drill a hole in the center of each outline. Insert screws, leaving space between the screw head

and the joist. Screws are not provided.

C18

Attach the rails onto the screws. Tighten screws.

12

C19

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may

need to be purchased.

C20

Route wires through the strain relief.

42929-01 10/26/2010

C21

Tighten the strain relief screws.

C22

C23

Black

2 Pin

White

Fan Motor

White

3 Pin

Light

*Option Fan & Main Light Together

Black

*Option

Light

Connect wires as shown.

C24

Ground

Green

A

Bare Copper

Black

Main Switch 1 (AC In)

White

Black

Switch 2 (AC In)

H

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under the

42929-01 10/26/2010

wiring cover plate.

G

I

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

13

C25

42929-01 10/26/2010

C26

I

Reinstall the motor by inserting the tabs and pushing up

into position. Make sure the wires are not pinched

between the motor and the housing.

C27

Turn on the power source.

J

Secure the motor by tightening the 2 screws.

C28

ON

OFF

Test the motor. If the motor does not run,

check the plug connection.

14

C29

Go to step

E1

on page 17

to attach grille.

42929-01 10/26/2010

Existing Construction – accessible only from below

D11

Remove an existing fan and check to make sure the open­ing is large enough to accommodate the new motor hous-

EXISTING FAN

ing (8”x 8 1/2”).

D13

D12

F

Move the housing into position above the ceiling

D14

D15

Route wires through strain relief.

2

1

Attach existing ducting to duct connector. Tape joints.

If ducting does not fit securely,

an adapter may need to be purchased.

Install the housing flush with the sheetrock and secure by

tightening the pre-loaded screws into the joist.

42929-01 10/26/2010

F

15

D16

42929-01 10/26/2010

Black

2 Pin

White

Fan Motor

White

3 Pin

Light

*Option Fan & Main Light Together

Black

*Option

Light

Connect wires as shown.

Ground

Green

A

Bare Copper

Black

Main Switch 1 (AC In)

White

Black

Switch 2 (AC In)

D17

G

H

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under

the wiring cover plate.

D19

D18

I

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

D20

16

I

Reinstall the motor by inserting the tabs and pushing up

into position. Make sure the wires are not pinched between

the motor and the housing.

J

Secure the motor by tightening the 2 screws.

42929-01 10/26/2010

D21

D22

ON

OFF

Turn on the power source.

D23

Go to step

E1

on page 17

to attach grille.

Attaching the Grille

Test the motor. If the motor does not run, check the plug

connection.

E1

N

42929-01 10/26/2010

E2

F

M

Remove the thumbscrews. Connect wiring harness. DO NOT ALLOW THE FIXTURE TO

HANG FROM THE WIRING HARNESS.

17

42929-01 10/26/2010

E3

E4

E5

M

Remove the strain relief bracket screw. Position the strain relief bracket under the

motor as shown.

M

E6

M

K

M

18

Insert the strain relief bracket’s dog-leg tab so that

it hooks over the lip of the motor. Reinstall the

strain relief bracket screw.

E7

N

Attach thumbscrews.

WARNING: To reduce the risk of electrical shock,

all 4 thumbscrews MUST be properly installed.

Align posts A, B, C and D (stamped into motor hous-

ing) with posts A, B, C and D (stamped into light

fixture). Slide light fixture over posts.

E8

Install bulbs (not included).

42929-01 10/26/2010

E9

E10

O

P

Align glass dome and push up.

Complete.

Screw finial into position.

42929-01 10/26/2010

19