Hunter Fan 45057-01 User Manual

For Your Records and
Warranty Assistance

For reference, also attach your receipt or a copy
of your receipt to the manual.

__________________________________________
Model No.

__________________________________________
Date Purchased

__________________________________________
Where Purchased

Type 2 ModelsType 2 ModelsType 2 Models

Owner’s Guide and Installation Manual

English Español

Form# 45057-01
20090624
©2009 Hunter Fan Co.

Table Of Contents

1 • Getting Ready. . . . . . . . . . . . . . . . . . . . . . 4

2 • Installing the Ceiling Plate . . . . . . . . . . 5

3 • Assembling and Hanging the Fan . . . 6

4 • Wiring the Fan . . . . . . . . . . . . . . . . . . . . . 7

5 • Installing the Canopy and Canopy

Trim Ring . . . . . . . . . . . . . . . . . . . . . . . . . 8

6 • Assembling the Blades. . . . . . . . . . . . . . 9

7 • Completing Your Installation With a

Light Fixture . . . . . . . . . . . . . . . . . . . . . . 10

8 • Operating and Cleaning Your Ceiling

Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

9 • Troubleshooting. . . . . . . . . . . . . . . . . . . . 14

Welcome

Your new Hunter® ceiling fan is an addition to your home or oce that
will provide comfort and performance for many years. is installation
and operation manual gives you complete instructions for installing
and operating your fan.

We are proud of our work. We appreciate the opportunity to supply
you with the best ceiling fan available anywhere in the world.

Before installing your fan, for your records and warranty assistance,
record information from the carton and Hunter nameplate label
(located on the top of the fan motor housing).

Cautions and Warnings

• READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING
INSTALLATION. SAVE THESE INSTRUCTIONS.

• Use only Hunter replacement parts.

• To reduce the risk of personal injury, attach the fan directly to the
support structure of the building according to these instructions,
and use only the hardware supplied.

• To avoid possible electrical shock, before installing your fan,
disconnect the power by turning o the circuit breakers to the
outlet box and associated wall switch location. If you cannot lock
the circuit breakers in the o position, securely fasten a prominent
warning device, such as a tag, to the service panel.

• All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualied electrician.

• To reduce the risk of personal injury, do not bend the blade
attachment system when installing, balancing, or cleaning the fan.
Never insert foreign objects between rotating fan blades.

• To reduce the risk of re, electrical shock, or motor damage, do not
use a solid-state speed control with this fan. Use only Hunter speed
controls.

© 2009 Hunter Fan Company

2

45057-01 • 06/24/09 • Hunter Fan Company

Installer’s Choice and Optional Accessories

Support Brace

Standard
Mounting
Style

Standard Mounting hangs from the
ceiling by a downrod (included).

Support Brace

Ceiling
Outlet Box

Angled
Mounting
Style

Ceiling
Outlet Box

12

Understanding Mounting and Installer’s Choice®

Hunter’s patented 3-position mounting system provides you maximum
installation exibility and ease. You can install your Hunter fan in one
of three ways, depending on ceiling height and your preference: Low
Prole, Standard, or Angled mounting. e steps in this manual include
instructions for all three Installer’s Choice mounting methods.

Considering Optional Accessories

Consider using Hunter’s optional accessories, including a wall-mounted
or remote speed control. To install and use the accessories, follow
the instructions included with each product. For quiet and optimum
performance of your Hunter fan, use only Hunter speed controls.

For ceilings higher than 8 feet, you can purchase
Hunter extension downrods. All Hunter fans use
sturdy 3/4” diameter pipe to assure stability and
wobble-free performance.

8

Low Prole
Mounting
Style

Support Brace

Ceiling
Outlet Box

CAUTION: To

reduce the risk of
personal injury, attach
the fan directly to the
support structure of
the building according
to these instructions,
and use only the
hardware supplied.

Angled Mounting recommended for a
vaulted or angled ceiling

45057-01 • 06/24/09 • Hunter Fan Company

Low Profile Mounting ts close to the
ceiling, recommended for ceilings less
than 8 feet high

3

1 • Getting Ready

To install a ceiling fan, be sure you can do the following:

• Locate the ceiling joist or other suitable support in ceiling.

• Drill holes for and install wood screws.

• Identify and connect electrical wires.

• Lift 40 pounds.

If you need help installing the fan, your Hunter fan dealer can direct
you to a licensed installer or electrician.

Gathering the Tools

You will need the following tools for installing the fan:

• Electric drill with 9/64” bit

• Standard screwdriver (magnetic tip recommended)

• Phillips-head screwdriver (magnetic tip recommended)

• Wrench or pliers

• Ladder (height dependent upon installation site)

Checking Your Fan Parts

Carefully unpack your fan to avoid damage to the fan parts. Refer to
the included Parts Guide. Check for any shipping damage to the motor
or fan blades. If any parts are missing or damaged, contact your Hunter
dealer or call Hunter Technical Support Department at 888-830-1326
(In Canada, call 1-866-268-1936).

Installing Multiple Fans?

If you are installing more than
one fan, keep the fan blades and
blade irons (if applicable) in sets,
as they were shipped.

Preparing the Fan Site

Before you begin installing the fan, follow all the instructions in
the pullout sheet called “Preparing the Fan Site.” Proper ceiling fan
location and attachment to the building structure are essential for
safety, reliable operation, maximum eciency, and energy savings.

4

45057-01 • 06/24/09 • Hunter Fan Company

2 • Installing the Ceiling Plate

CAUTION: To avoid possible electrical shock, before installing your fan,

disconnect the power by turning o the circuit breakers to the outlet box
and associated wall switch location. If you cannot lock the circuit breakers
in the o position, securely fasten a prominent warning device, such as a
tag, to the service panel.

2-1. Drill two pilot holes into the wood support structure through the

outermost holes in the outlet box. e pilot holes should be 9/64”
in diameter.

For Angled Ceilings: Be sure to orient the ceiling plate so that the

two tabs are pointing toward the ceiling peak.

2-2. Your fan comes with four preinstalled noise isolators. Check to

make sure all four isolators are in place and were not removed
during shipment.

2-3. Place a at washer on each of the two 3” wood screws.

2-4. read the supply wires from the outlet box in the ceiling through

the hole in the center of the ceiling plate.

2-5. Align the slotted holes in the ceiling plate with the pilot holes you

drilled in the wood support structure. For proper alignment use
slotted holes directly across from each other.

Note: e isolators should be ush against the ceiling.

2-6. Pass the screws through the slotted holes in the ceiling plate into

the pilot holes you drilled.

Tighten the screws into the 9/64” pilot holes; do not use lubricants

on the screws. Do not over tighten.

Toward
Ceiling Peak

For Angled Ceilings: Be sure to orient
the ceiling plate so that the two tabs
are pointing toward the ceiling peak.

Flat Washer

45057-01 • 06/24/09 • Hunter Fan Company

3” Wood

5

Screw

Ceiling
Plate

Steps 2-3 – 2-6